- NerfHaven
- → BloodMoon's Content
BloodMoon's Content
There have been 88 items by BloodMoon (Search limited from 04-January 97)
#64930 At2k Tank Expansion
Posted by BloodMoon on 02 October 2005 - 10:32 PM in Modifications
I have never enlarged a tank before myself...I don't see a ton of benifit, but I'm just waiting to be proven wrong on that.
#66184 The Hornet
Posted by BloodMoon on 20 October 2005 - 08:32 PM in General Nerf
I'd really like to get my hands on a Hornet, but I'm not about to buy a N-Strike, considering that they're $40 and I don't want/need the Titan or the Scout (nevermind anything else the N-Strike comes with). If they were sold individually, I'd gladly pay $15 for one, but I'm not motivated enough to find one to buy online.
#65110 Performance Problems With Airtech 3k
Posted by BloodMoon on 05 October 2005 - 05:05 PM in Modifications
#65131 Performance Problems With Airtech 3k
Posted by BloodMoon on 05 October 2005 - 08:24 PM in Modifications
#66764 Tagger Mods?
Posted by BloodMoon on 29 October 2005 - 04:47 PM in Modifications
#64929 At3k Help
Posted by BloodMoon on 02 October 2005 - 10:27 PM in Modifications
As far as a good barrel replacement:
If you're looking to single the AT3K (I have one singled because the rotator broke) you can replace the barrel with pretty much anything that you have lying around that fits your darts, it doesn't have to be PETG.
The reason that most mods are PETG is because you're limited on room if you want to keep the six rotating barrels. PETG fits nicely, but you can also use 9/16" OD Brass for very similar performance. Crayola barrels would probably fit nicely (I plan on trying that out on an AT3K that I have lying around). Anything with a bigger outer diameter, like PVC, will be a pain to fit in the six barrel slots, if it's even possible.
I'm sure there's a restrictor removal somewhere, but I don't remember seeing one...a barrel replacement will most likely be a lot easier.
#65076 At3k Help
Posted by BloodMoon on 04 October 2005 - 09:50 PM in Modifications
#66712 Styling Glue Help
Posted by BloodMoon on 28 October 2005 - 05:56 PM in Modifications
#66186 Tool Prerequisites
Posted by BloodMoon on 20 October 2005 - 08:42 PM in Modifications
I don't know if you count this as a tool, but I use a vice all the time, for letting stuff dry and holding things that I need to drill/sand.
Something that I can't get enough of that hasn't been mentioned is Electrical Tape (also called Vinyl Tape or E-Tape). My main use for it is that wrapping pipe/tubing with it increases the outer diameter. I've also seen it used for added holding strengh and better grips for your guns. If nothing else, it makes things black (or whatever other color of E-Tape you'd like to buy).
#66089 Air Tank Mod
Posted by BloodMoon on 18 October 2005 - 09:31 PM in Modifications
When I range tested, I got between 100' and 123' consistantly, with no mod to the tank itself (only the trigger). I thought that was a little high. In reality, I found out that my while the coupler is centered side-to-side, it angles the barrel upward. With a level shot, the range will be less.
Unlike you, I can't say that I've found this gun to be very accurate. With my 12" barrel, which works better than the 8" one I had before, I only shoot at people 60' away, closer if they're moving fast.
Here's some pics of my LBB:
#64925 Rf20 Problems
Posted by BloodMoon on 02 October 2005 - 10:11 PM in General Nerf
#66763 The Firefly, How Do We Modify This Monster...
Posted by BloodMoon on 29 October 2005 - 04:41 PM in Modifications
the Renegade FireFly Mod
#66027 Gun Idea
Posted by BloodMoon on 17 October 2005 - 06:55 PM in Modifications
In general, I don't think it's a good idea to start a new topic when you don't really care about the results (you're not even going to TRY to build one).
#66426 Airtech 3k Tubing Blown!
Posted by BloodMoon on 23 October 2005 - 03:54 PM in Modifications
#66357 Airtech 3k Tubing Blown!
Posted by BloodMoon on 22 October 2005 - 10:12 PM in Modifications
#66427 New Home Made Darts
Posted by BloodMoon on 23 October 2005 - 03:56 PM in Modifications
#63645 What Size Pipe
Posted by BloodMoon on 14 September 2005 - 07:48 PM in Modifications
If you want to use a ramrod/breech/bolt/nested barrel, I'd take poo's suggestion on the the 1/2", Sch. 40 PVC.
EDIT: 1/2" Sch. 40 PVC has an inner diameter of 5/8"...I don't know what the outer diameter is, but it's not as important.
#65792 New Stefans And Shotgun Idea
Posted by BloodMoon on 14 October 2005 - 06:46 PM in General Nerf
#65816 New Stefans And Shotgun Idea
Posted by BloodMoon on 15 October 2005 - 10:32 AM in General Nerf
#67496 1" 200 Psi Pvc
Posted by BloodMoon on 11 November 2005 - 10:43 PM in Homemades
As for the places that DO carry the pipe, Lowes is a haul for me, but they carry more types of PVC than anywhere else I've been to, thin-wall included. I get most of my thin-wall from a locally-owned store called Wentworth Lumber Yard. Just see what kind of places in your area.
#66358 Springs
Posted by BloodMoon on 22 October 2005 - 10:18 PM in Modifications
For all of the hardware stores I've been in, there's been a wall of springs somewhere. Just ask someone who works there...unlike some items (like brass), springs are really common, and the people working at your hardware store should know where they are. As far as the three stores nearest to me, however, I've been unable to find any good springs for use in cocking guns, so I'm going to try to get ahold of some AR15 springs, as per Boltsniper's Homemades.In what section of your hardware stores do you find the springs?
#65979 At2k Stock
Posted by BloodMoon on 16 October 2005 - 10:49 PM in Modifications
#63146 7/16 Backer Rod?
Posted by BloodMoon on 05 September 2005 - 08:47 PM in Modifications
#66354 New Silencer
Posted by BloodMoon on 22 October 2005 - 09:56 PM in Homemades
Just a question on the function of your silencer...I'm assuming that the noise reduction is really only an issue for pump guns, seeing as in a spring gun the sound of the spring colliding with the end of the plunger tube is louder than the dart firing (though I may be wrong)?
#67615 The Soloution To Glue Dillema
Posted by BloodMoon on 13 November 2005 - 10:07 PM in Modifications
#69951 Chewbacca's Mauser
Posted by BloodMoon on 27 December 2005 - 12:14 PM in Modifications
#66182 Paper Darts?
Posted by BloodMoon on 20 October 2005 - 08:26 PM in General Nerf
I can't imagine that any darts made out of paper are as good as stefans. For starters, they have to have almost no wieight...which poses problems if you want to shoot over five feet. Next, how can they possibly make a good seal with the barrel? As they must be easily bent, I doubt that there's any good barrel for them.
#65478 Simple Lbb Mod
Posted by BloodMoon on 10 October 2005 - 06:46 PM in Modifications
Could you pump the gun less because it is only firing stefans instead of bulky foam missiles? Yes, you can. But in a war, unless you're really desperate, you're going to want to pump it that many times because that way you'll get greater range.
#66518 Barrel Selection
Posted by BloodMoon on 24 October 2005 - 06:03 PM in Modifications
If you can't get brass, that I can assume that you also can't get PETG. The other barrel materials to consider are Sch. 80 PVC (haven't used this, but some people claim it works) and Crayolas. Crayolas might be a good, slightly less constricted alternative to CVPC for your guns.
In general, if you have a spring gun (or any gun with a high air volume / slow air delivery), you will benefit from a constriction.
#66618 Barrel Selection
Posted by BloodMoon on 26 October 2005 - 07:42 PM in Modifications
#63591 Buzuca
Posted by BloodMoon on 13 September 2005 - 07:59 PM in Modifications
If you take a look at the NF innards, you'll see that pulling the trigger lightly brings two metal pieces together, completing the circuit to lite the NF light. Now you have to figure out a way to install these metal pieces in your other gun (which I'm guessing is not easy, if it's even possible). Then you'll have to find a way to cut the battery case out of the NiteFinder grip...and then unscrew the laser light, snip the wires, and then rewire it up again correctly in the new gun.
If you have your heart set on one of these things, your best bet is to go to Wal Mart and buy a 'Daisy Electronic Point Sight' or the like. They are about $8 ea, and then you can either make your own dovetail mount or just take some e-tape and tape it to the top of your gun (or the side, if you prefer).
#69053 Question About The Far
Posted by BloodMoon on 11 December 2005 - 07:33 PM in Homemades
I'm thinking that it would be actually cheaper to buy a springer than to try and get all the parts for building a homemade one.
Also, I'm not sure the FAR is the best place to look for ideas on this. The FAR was designed with bulky foam ammunition in mind, so I don't know how much of Bolt's design is going to be relevant to what you're trying to do. The FAR is a good primer for a project like this, but I think that you're going to have to redesign the magazine system to work with the BB's, which will be no small feat.
#66771 Dart Tag Firestrike In Stores!
Posted by BloodMoon on 29 October 2005 - 08:14 PM in General Nerf
#67077 Size Of Pvc For Homemade Gun
Posted by BloodMoon on 03 November 2005 - 07:01 PM in Homemades
I measured some 1", and that chart seems about right, so I'd say it's pretty safe to assume that the chart is correct for the rest of the pipe sizes.
Unfortunately, it doesn't list ID's and OD's for thin wall PVC (for example, 230 PSI 3/4" PVC or 200 PSI 1" PVC), which you may want in your design.
#64360 New Clip
Posted by BloodMoon on 25 September 2005 - 10:25 PM in Homemades
As far as the M1 clip, I won't have a good idea about it for sure until I try to build one. I don't think it would be all that bad to make a clip that fits inside the mag (so to say). In my mind, I'm just tring to think about ompa's clip and then what parts of it would have to be in the stationary mag and what parts would be in the removable clip. In the M1 clip idea, would you have to have a section of the barrel attached to the removable clip, that the bolt would go in? Or would you not have to worry about that?
#64309 New Clip
Posted by BloodMoon on 25 September 2005 - 11:49 AM in Homemades
#64810 Do You Search?
Posted by BloodMoon on 02 October 2005 - 09:16 AM in General Nerf
site:nerfhaven.com "your-search-here"
into the search bar.
- NerfHaven
- → BloodMoon's Content
- Terms of Service and Privacy Policy
- Code of Conduct ·