Quilan Fett's Content

#159712 Longshot Troubles

Posted by Quilan Fett on 19 June 2008 - 11:25 AM in Modifications

The ID of the LS PC is Slightly larger (millimeters) than the ID of 1.25" PVC. But since the stock plunger chamber is thinner, 1.25" PVC probabally won't fit. I'd try thinwall 1" and a new plunger head.

#162333 Two Questions About Homemades

Posted by Quilan Fett on 11 July 2008 - 12:50 AM in Homemades

As Carbon said, the brass fits. Also, soe PVC cement only works for one kind, but some work for both 40 and 80.

#151352 Magstrike Problem

Posted by Quilan Fett on 15 April 2008 - 08:39 PM in Modifications

Does this by any chance start after twenty or so pumps?

#148933 Well, April 1st Has Come And Gone?

Posted by Quilan Fett on 02 April 2008 - 08:03 PM in Off Topic

I think that April Fools should last the whole month. The way it is now, iti si so obvious that it is a joke.

I missed your x-bow thread, but I had planned to do the same with a SuperTech 9000. I chickened out because I figured I'd get banned.

#147602 What Parts From A Maverick?

Posted by Quilan Fett on 28 March 2008 - 09:29 PM in General Nerf

Is the outer tube or the inner tube broken. The outer has the same ID as 3/4" Sch40 PVC, I think. As for the inner, you can just cut the back and front off and splice a different tube in.

#176559 +bow Addition

Posted by Quilan Fett on 11 September 2008 - 09:11 AM in Modifications

if this is improving the ranges, you did not do the rest right. Try putting some e/teflon tape under your O-rings.

#166695 National Geographic Gun Problems

Posted by Quilan Fett on 05 August 2008 - 12:40 AM in Modifications

You can flre it flat stock by pulling the trigger halfway at 45 degrees then leveling it.

#212860 Ebay Question

Posted by Quilan Fett on 16 February 2009 - 06:56 PM in Off Topic

http://www.mailinator.com/

If you don't let e-bay send you any credit card numbers or paypal passwords (Not sure if this is possible (I don't use e-bay)), you should be fine.

#212049 Night Finder

Posted by Quilan Fett on 13 February 2009 - 06:30 PM in Site Feedback

^ Pot calling the kettle black?

#202891 Expanding Brass Half-pipes

Posted by Quilan Fett on 12 January 2009 - 06:41 PM in Modifications

I usually use a dremel with a cutting wheel to cut it.

What cutting wheel are you using? If it is a wood/plastic, tile, anything other than a thincut metal wheel, you WILL have these problems. If it is, then the brass may be bad. Get it from Hobby People, they have wonderful brass.

I used a standard non-reinforced and it cut fine. By the time I was done with the breech, the wheel was the size of a mini-marshmallow though.

#213820 Roto Rocket Mod

Posted by Quilan Fett on 20 February 2009 - 10:26 PM in Modifications

Nope. See, the barrel is part of the tank. So don't cut it.

#214300 Snowskate Help

Posted by Quilan Fett on 22 February 2009 - 08:39 PM in Off Topic

Register on a Snowskate forum.

#149598 Plunger Tubes

Posted by Quilan Fett on 06 April 2008 - 01:00 AM in Modifications

http://www.cabelas.c...equestid=104729

#151335 Firefly Shotgun

Posted by Quilan Fett on 15 April 2008 - 08:00 PM in Modifications

Redially avaliable at Target.

#149575 Plunger Tubes

Posted by Quilan Fett on 05 April 2008 - 10:41 PM in Modifications

Thinwall 3/4" PVC is said to work.

#156234 The Latest From N-strike: Coming Fall 2008

Posted by Quilan Fett on 19 May 2008 - 01:00 AM in General Nerf

This reminds me of this dream I had many months ago where someone posted about a nerf gun just like this one. Then again, I also remember that the day after, purple monkeys invaded my school. It's possible I am confusing my dreams and reality. But good find.

#197031 Spring Replacment

Posted by Quilan Fett on 18 December 2008 - 07:12 PM in Modifications

What makes a bigger difference than the material is the thickness and length of the spring. If aluminum has any advantage over steel, it would be impossible to measure since steel is denser, so more aluminum would have to be used to make up for it. At that point, you could just add a little more and make it stronger. Even if you manage to get two springs of different materials that have the exact length and spring rate, the only factor would be how fast they un-compress. I think it would be more worthwhile to experiment what effects different spring rates have and talk about the law of diminishing return.

#146486 Missing Nf Catch Spring

Posted by Quilan Fett on 23 March 2008 - 06:46 PM in General Nerf

Just use a pen spring.

#159901 Morg Writeup

Posted by Quilan Fett on 21 June 2008 - 11:25 AM in Homemades

It was actually a very comfortable gun, especially with a stock attached. But this gun is now dead, so its thread deserves no more replies.

#190614 Rapid Fire 20 Question

Posted by Quilan Fett on 18 November 2008 - 08:44 PM in General Nerf

The material of the bladder itself is rated to 500PSI. The Nylon fittings however are rated to 150PSI. The stock pump can only fill the stock bladder to about 60PSI.
The points of failure involved are the end caps of the bladder not being secure, or using a hose clamp without padding, causing it to cut into the bladder.

Also, FA24 pumped his 80 times:
http://nerfhaven.com...indpost&p=91496

#145947 Newbie Needs Help

Posted by Quilan Fett on 20 March 2008 - 09:26 AM in Modifications

You might have gotten a bad seal, or it jus might not have helped range. Some mods don't actually work as well as people say they do.

#107434 Nite Finder Mod Messed Up

Posted by Quilan Fett on 24 May 2007 - 06:14 PM in Modifications

OK, i think i'm going to ditch that barrel and get a pvc.
(now i just gotta remove about 3 sticks of hot glue from my nite finder

PVC is also too big for 1/2 in stefans.

#107419 Can This Be Modded?

Posted by Quilan Fett on 24 May 2007 - 05:00 PM in General Nerf

I can get it too go over 50' easy. One missile topped over 60'.

So it's medium-ranged crap. Why not just carry a chimp to throw its own shit at your opponents then?

This once got me banned from a war.

#128417 Homemade Gun Shells

Posted by Quilan Fett on 03 November 2007 - 12:36 PM in Homemades

I think there was a thread about this before, but to use it to copy the manta ray.

#124195 Extended Rfr/clip Tek Clip?

Posted by Quilan Fett on 26 September 2007 - 04:18 PM in Modifications

I am on the edge about buying a clip tek and I want to know wether it is possible to extend the clip to hold more shells like Captian Slug's Longshot mod.

#115273 Power Trip

Posted by Quilan Fett on 10 July 2007 - 03:29 PM in Articles

That being said, these powerful weapons can give you the upper hand in a long range fight without hurting anyone. At the war on Saturday, a titan, sm5k, and my rocket man shooter were all used.

Can you tell us what a rocket man shooter is?

#107438 Nite Finder Mod Messed Up

Posted by Quilan Fett on 24 May 2007 - 06:35 PM in Modifications

http://denoffoam.tripod.com/id59.html

#135343 Fun Free Online Games

Posted by Quilan Fett on 08 January 2008 - 10:58 PM in Off Topic

I play MechQuest and AdvetureQuest.

#138375 How Many Times Have You Been Sigged?

Posted by Quilan Fett on 03 February 2008 - 12:05 PM in Off Topic

Never.

#145327 Maxshot Questions...

Posted by Quilan Fett on 15 March 2008 - 11:44 PM in Modifications

Why don't you just do one side for the telescoping effect?

#145870 What's This?

Posted by Quilan Fett on 19 March 2008 - 08:10 PM in General Nerf

How about a link to the review?

#145173 Who Has Some Money They Want To Blow?

Posted by Quilan Fett on 14 March 2008 - 11:18 PM in General Nerf

Transformers blaster for $10.

http://www.amazon.co...05554654&sr=1-1

#144922 Plunger Tubes

Posted by Quilan Fett on 12 March 2008 - 08:52 PM in Homemades

Just use PVC. Follow Carbon's SNAP writeup.

#142072 Morg Writeup

Posted by Quilan Fett on 22 February 2008 - 10:31 PM in Homemades

This gun is based off of Carbon's SNAP and uses FA_24's Deoderant clip. It is not all mine. This being said, I compiled it myself and I think my breech is original. It can be made with about $20 and works great. Also, for the sake of this write-up not being terribly long, I have linked to other write-ups to follow for more details.

Ranges-

35
42
60
61
62
65

With 6" barrel extention

45
50
67
68
69
69

I used a variety of dart thickness for these, hence the wide variation. Also, these tests show that I should have chosen a longer barrel- perhaps 4" longer. That is for my darts, though, which are loose enough to use CPVC.

Without further adoo-

MORG

The gun itself
Posted Image

Uncocked

Cocked

The Trigger

Posted Image

Uncocked

Cocked

Breech partway open

Posted Image

Size comparison

Posted Image

Specs

Description............Multi Shot Primary
Designation..........................MORG!
Release Date.....................Jan 2008
Caliber..............0.54" (Micro Stefans)
Operation...............Pull-Push Foregrip
Propulsion...................Spring Plunger
Magazine............Detachable Top Feed
Mag Capacity................................6
Overall Length.......................25.5 in
Weigh.....................................2.3lb
Barrel Length...........................14 in
Max Rate of Fire.........................N/A
Max Range.................................70'
Effective Range...........................55'
Accurate Range...........................40'
Intended Use........................Primary

Materials:

For Plunger

1' 1.25" PVC
1x Clothespin
1x Nail (for trigger)
2x 1.25" PVC coupler
2x 1.25" to .5" PVC reducing bushing
1x Angle bracket (for trigger)
1' 1" PVC (for spring guide)
1x .75" PVC endcap
.5' .75" PVC
2x Handyman 9713 Spring
1x .75" to .5" PVC reducing bushing
1x .5" CPVC endcap or coupler

Rest of Gun

1' .5" PVC
1' 19/32" Brass
11" 9/16 PETG (lengthen for dart tightness)
1x .5 PVC tee
2' Threaded metal rod
4x Nuts to go on rod
2x Angle brackets to go on rod
.5' 1/2" Brass
1x Rightguard gel deoderant stick
1x Dead 9v battery
1' 1" PVC (for handle)
1x .75" PVC coupler
.5' .75" PVC

Tools

Epoxy Putty
Plumber's Goop
Wire cutters
Hacksaw/PVC cutters
PVC cement
Hammer
Complex $50,000 specialty machine that no one actually owns

To start, this gun uses the build of Carbon's Snap 1 with a few tweaks.
http://www.boltsnipe...ap-1/SNAP1.html

I used a O-ring plunger instead of a washer. Though the linked wirte-up is made for thinwall 1' PVC, it is pretty similar.
<a href="http://nerfhaven.com...showtopic=6934" target="_blank">http://nerfhaven.com...wtopic=6934</a>
I used a 3" CPVC plunger rod. The spring fits well over it.
I used a small peice of 1' PVC to support the spring. It fits in the back of the plunger tube and is just short enough not to interfere with the plunger.
I put a coupler and 1.25"-.5" PVC reducing bushing on the front and back. If you want a cleaner look, you can put an endcap on the back, but you will loose the ability to attach a stock. Note:don't glue the front reducer on yet
For the plunger head assembly, put the o-ring in a slot in the .75" PVC endcap. Inside of the endcap, put the .75" to .5" PVC reducing bushing. Inside this, place the CPVC fitting with the CPVC inside it. You will then need to sand down the endcap and bushing to let the nail reach the catch slot.

Now that you have your main body, we can start the actual writeup.

To start, take the front 1.25" to .5" PVC reducing bushing and glue half of the .75" PVC coupler in the inside of it with the loose end facing away from the .5" side. Now cut a 1" peice of .75" PVC. Next, cut a 5.5" peice of 19/32" brass. Glue a 5" peice of 1/2" brass inside it. Glue the end of the brass with the glue in it in the peice of .75" PVC that you just cut and put it in the gun with the brass sticking out of the front bushing. I also recomend gluing some FBR onto the peice of .75" PVC to help silence the gun.

Cut a 4.25" Peice of .5" PVC. Now, glue one end into your .5" PVC tee. Now, using FA_24's guide, put the deoderant clip as close to the tee as you can.
When making your clip, keep the peice that attaches to the screwey part that pushes the gell down. Sand this peice dawn so that it slides easialy in the clip and use it as your feeder (peice that pushes darts down). Put your 9v battery on top of it to weigh it down.
Note: this is the time at which you will have the choice to make a foregrip (like I did) or a side bolt (like the Longshot). For the foregrip, put your clip on opposite the tee. For a side bolt, put the clip on perpendicular to the tee.

Clip write-up
http://nerfhaven.com...showtopic=6370=

Once the clip is done, glue the 19/32" brass in the .5" PVC just behind where the dart will load and on the side without the tee.

The clip
Posted Image

You are almost done.
Next, take your peice of PETG and put it in the brass. Now hold it still and cock your gun. Mark where the dart will load once it is fully cocked and cut the breech opening. Make sure that the brass sufficently covers the opening when it is in the forward position.

Now, drill two holes in your front reducing bushing the size of your metal rods. Screw the rods into the holes you just made. Now screw two nuts, a bracket, then two more nuts onto each rod on the end. Make sure that the PETG barrel in place so that it is open when the priming handle is back and covered when the priming handle is forward and glue it onto the angle brackets.

Other Construction Specs

Length of 1.25" PVC with both couplers glued on - 12" exactly
Distance from end of front 1.25" coupler to trigger catch - 6.5"
Ammount of hot glue used - 20lbs

Again, I can't stress enough how much credit goed to Carbon, ForsakenAngel_24, and Gyrvalcon for doing my write-ups for me.

#142091 Morg Writeup

Posted by Quilan Fett on 23 February 2008 - 12:00 AM in Homemades

I am actually taking suggestions for a new name, since MORG stands for Mostly Opperational Rof Gun and it is now fully opperational.

Also, for all who were wondering, Mead Me Homy Fern Gnu is an anagram for "My homemade nerf gun". Also possible, "Famed Gunnery Eh Mom", "My Foamed Gunner Hem", "Famed Rogue Men Hymn", "Deaf Gunner Eh Mommy", and "Fanged Her One Mummy"

If you are still confused, a gnu is a wildebeest, so Mead me homy fern gnu basically means, "meet me homie fern wildebeast".

It's called a Pistol Splat. I don't know where you can find them though. But it is indeed a paintball gun without co2.

http://www.pwpaintba...istol_splat.htm

By content type

See this member's

Sign In