Edited by CaptainSlug, 22 March 2010 - 06:31 AM.
Modification and Paintjob Pictures
#2976
Posted 21 March 2010 - 11:23 PM
#2977
Posted 23 March 2010 - 02:14 AM
-
-
-
Is it a bit plain or does it look OK?
#2978
Posted 23 March 2010 - 11:39 AM
I think the ammo belts are much more useful for holding alternative ammo rather then darts. Each clip band holds 2 arrows. If you pull out the stitching between the clip band and it's spacer
you can hold a Titan missile. If you pull out the stitching of every other single dart holder it fits an arrow perfectly (that every other as in alternating, don't pull out all of the stitches!). For those that don't know a Longshot faux barrel is actually perfect for shooting arrows with (and pretty good for shooting megas too). So its very easy to setup a Lanard hand cannon or other high powered blaster to shoot arrows with.
TetraStrike with some short brass barrels and a better pump. The pump is from some Air Hogs thing and I plugged it up. It can get about 3-4 pumps in before it gets too hard to bother with more.
Shoots both stock darts and stefans about 70', so it could probably use longer barrels.
Airsoft shotgun I got from Ax-Man. The only really cool part about this mod is that I did it all without opening up the blaster. I think it was getting about 50 feet but the seal is horrible. It is also...
...rearloading, which is pretty sweet. The seal is mostly just silicone sealant that I let dry while the plunger tube was held back. I did something similar with my doubleshot, which worked
awesomely, but this one didn't turn out. Part of the problem is that the seal relies on you pulling and holding the pump forward, since nothing else is holding the plunger tube against it.
Oh no, VelveetaAvenger broke his one blaster that was actually kind of cool! Not so fellow Nerfers! I just finally figured out how easy it is to remove the turret, if you have a long enough
screwdriver. It's held on by a single screw in the exact center of the turret, I just had to drill into the top with a spade bit to get at it. This means I can put a turret full of looser barrels on
it for the summer, when darts heat up and expand. I also sliced off the old o-ring seal and gooped on a (hopefully) superior foam seal. The foam came from one of those blank cd things you buy.
Edited by VelveetaAvenger, 23 March 2010 - 11:43 AM.
#2979
Posted 23 March 2010 - 05:06 PM
Edited by nate the great, 24 March 2010 - 02:22 PM.
2 slingshot weights is basically a steel bullet with a foam sabot
-Mr BadWrench
You have a tampon on your gun. There's your problem.
-Hi Yah!
Join the Revolution!
#2980
Posted 23 March 2010 - 10:25 PM
Fully modified "Pullback" PAS.
Contract Wes7143 if you want an awesomely modified blaster/a paint job of amazing quality.
Edited by Noodleownz, 23 March 2010 - 10:29 PM.
#2981
Posted 23 March 2010 - 11:04 PM
Who needs a workbench when you have McDonald and Taco Bell trays.
Edit: And by Pistol Splat I of course mean Wipeout.
Edited by cheyner, 23 March 2010 - 11:43 PM.
Beaver's post claiming Kane's post claiming Demon Lord's post is correct is correct is correct.
Canadian Nerfers-R.I.P.
#2982
Posted 23 March 2010 - 11:29 PM
sub-optimal breech, yo.
OH WHAT SHOTGUN?
Unholy Three: DUPLUM SCRTA, DUPLUM PROBLEMA (2009)
But Zeke guns tend to be like proofs by contradiction
Theoretically solid but actually non-constructive
Rnbw Cln
#2983
Posted 23 March 2010 - 11:30 PM
Featuring a titan tank shit ball projectile system, phallus air input operation, and spinal tap launch preparation valve.
Also, place holder for more mods pics.
Edited by Split, 30 March 2010 - 12:28 AM.
#2984
Posted 23 March 2010 - 11:59 PM
First:
Draconis homemade trigger, Rev. 2 Slug breech and extended stock for big boy comfort. No internal modifications done yet.
Next:
Extreme overhaul here. Long barrel, PETG breech, custom wood grips, pump replacement and relocation.
And the breech open. Pretty sexy if I do say so myself.
#2985
Posted 26 March 2010 - 03:03 AM
-
#2986
Posted 26 March 2010 - 06:41 PM
The first gun I modded; shotgun fore grip, power stock, ar removal, and black and hot pink paintjob -ed recon.
Couplered Reactor
Rapidfire 20 and backpack tank
Nite-finder (spring addition and ar removal) and Pistol splat (barrel replacement)
Double-barreled Maverick
CPVCed Big Salvo
Wayne Tech Tri-fire blaster with 4x the RSCB goodness
Couplered Sonic Bazooka
ar-removed and painted Crossfire
painted Double-Shot (I know it looks realistic, but I'll never bring a stock double-shot to a war)
Edited by Coal Ten, 26 March 2010 - 07:29 PM.
#2987
Posted 27 March 2010 - 12:37 AM
#2988
Posted 27 March 2010 - 03:27 PM
But I discovered an extremely easy and effective way to replace the turret seal. Using the stopper from the front of the plunger.
Mini-writeup:
1. Take the stopper off the plunger. (Stole the pic from badwrench's writeup)
2. Widen the stopper's hole: Take a piece of brass. Center it over the hole and hit it with a hammer.
3. Put a couple layers of etape around the orange piece on the plunger tube.
4. Put the stopper of the plunger tube like so. Perfect new seal.
Edited in the Tetra Strike. It's a nice little gun.
Edited by oodalumps, 27 March 2010 - 05:49 PM.
#2989
Posted 27 March 2010 - 08:35 PM
Bags painted my 1500.
I got an Eliminator, for Don't Get Eliminated!!!11!!1
And a Secret Shot 2.
I got a ton of Man Cannon kills today.
UNHOLY THREE CONTRACT: A STOCK, PERFECTLY FUNCTIONAL SUPERMAXX 1000.
Unholy Three: DUPLUM SCRTA, DUPLUM PROBLEMA (2009)
But Zeke guns tend to be like proofs by contradiction
Theoretically solid but actually non-constructive
Rnbw Cln
#2990
Posted 28 March 2010 - 12:55 PM
#2991
Posted 28 March 2010 - 03:18 PM
Dart holders, made out of some scrap plastic.
The usual blessing.
#2993
Posted 28 March 2010 - 05:09 PM
The newest in trying to replicate the function of the crossbow. My now back up primary thanks to ASON I have an actual Xbow!
01:01 N9 I must make it clear though...I don't do cocaine.
#2994
Posted 28 March 2010 - 10:45 PM
It's a work in progress but so far I've done the AR removal and I'm integrating a chainsaw into the foregrip. I've given it a little paint job too and some LED's. Still needs about three or four more weekends of work till it's ready to go to a convention.
Here's a shot of the LED's lit up. And yes that's a toilet seat in my shed and no it's never been used.
My Long Strike
I've also done the AR removal on this one and I integrated the bi-pod from my longshot onto the extension. I'm planning to shave off the bottom part that sticks out and then plexiglass and bondo the gap between the bi-pod and the main body. I'm planning on doing an arctic digital camo paintjob for this once I'm finished with the Lancer-shot. And I'm planning on doing the light up optics mod for the scope as well.
Here's the view from the back. I think it kind of looks like an intervention from this angle.
#2995
Posted 29 March 2010 - 06:29 PM
This is my first painted gun, an old NiteFinder with the ARs removed.
I may put a CPVC/PETG barrel on it when I get around to getting the stuff.
DON'T! GET! ELIMINATED!!!
#2996
Posted 30 March 2010 - 09:20 PM
Check back to this post for updates
Contact me for design consultation relating to 3D Printing, CNC Machining, and Laser Cutting. I am always happy to collaborate on viable Open Source projects and/or business ventures.
#2997
Posted 30 March 2010 - 10:12 PM
My 1500 has rear-loadinz.
It's impressive how quickly this thread goes through a page.
#2998
Posted 30 March 2010 - 10:18 PM
Yessssss! Finally reinforced properly.
#2999
Posted 01 April 2010 - 03:30 AM
Quadshot with PVC and CPVC couplers nested under the PVC couplers. Barrels pictured are 5" PVC barrels for stock darts.
#3000
Posted 01 April 2010 - 10:14 AM
Last mods for these is to remove the bend at the end of the plunger rod and add an extension so I can put a proper handle rather than a key ring and paint.
Edited by popatachi, 01 April 2010 - 10:15 AM.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users