- NerfHaven
- → MindWarrior's Content
MindWarrior's Content
There have been 105 items by MindWarrior (Search limited from 16-December 96)
#276632 Semi-auto Shotgun
Posted by MindWarrior on 02 June 2010 - 01:31 AM in Homemades
#274552 At3k Singled Crayola Barrel
Posted by MindWarrior on 11 May 2010 - 06:40 PM in Modifications
PETG barrel: 12 inches.
More air is used efficiently to push the dart forward.
#288908 Happy Turkey Day!
Posted by MindWarrior on 25 November 2010 - 06:59 PM in Off Topic
#281449 Homemade Airtanks?
Posted by MindWarrior on 28 July 2010 - 01:17 AM in Modifications
#266262 Simple, Cheap And Effective Dart Mitre Box
Posted by MindWarrior on 21 February 2010 - 12:06 AM in Homemades
#266260 Simple, Cheap And Effective Dart Mitre Box
Posted by MindWarrior on 20 February 2010 - 11:55 PM in Homemades
Materials
From the following picture:
You'll need:
1. A glue gun
2. Some flat, hard, plate or surface, I used a CD case
3. A box cutter blade
4. Two segments of your airgun barrel material cut to the size you want your darts, make sure that they have straight, right angle cuts. I used Schedule 80 cpvc I had lying around, which has a VERY loose fit on my darts, and cut them to 1.5' and 1' segments. You can easily use OMC petg if you wish.
Construction
STEP 1
First, take your blade and slip it so it goes about 6/8ths in between the two CPVC segments as shown:
With the little bit of CPVC that does not have the blade covering, you can use to allign and straighten the two barrel pieces.
STEP 2
While tightly holding the two pieces of CPVC with your fingers, making sure not to off center the barrels, hot glue the bottom of the CPVC barrels and press it tightly on the plate or surface your using:
Ignore the cuts on the CPVC, I took this picture after I was done. You should waight, 10-15 seconds before letting go, this will let the hotglue expand the distance of the CPVC slightly, allowing very little wiggle room for the blade for a smoother cut. BTW, it LOOKS like theres a lot of space between the blade and barrel stub, but there isn't, I was pretty sloppy using a table saw and got some of the edges off the CPVC, but the barrels are still cut with a perfect 90 degree angle.
STEP 3
Now draw a cutting guide on your CPVC like so:
and use it as a guide for your dremel to get this:
And your done!
How to use:
Its actually pretty simple, just slip the foam through the opening until its flush with one end of your mitre box. The place one finger on each opening, on top of the foam, and lightly stretch it to help straighten the foam. Then, Place your blade on the slit, and cut!
I've learned that minimizing the amount of swipes for each cut should be minimized to two quick swipes to ensure a perfect cut.
At first when I first cut my first batch, they looked slightly off, but after heating my blanks the were or was near perfect. Hope this helps!
#278000 The Ak-47 Equivalent?
Posted by MindWarrior on 18 June 2010 - 02:47 PM in General Nerf
#266343 Simple, Cheap And Effective Dart Mitre Box
Posted by MindWarrior on 21 February 2010 - 05:25 PM in Homemades
@flipoffacliff: Good Idea.
#279891 Angel Breech Question
Posted by MindWarrior on 10 July 2010 - 02:45 AM in Modifications
#269728 Magstrike Problem
Posted by MindWarrior on 20 March 2010 - 11:40 AM in Modifications
#277185 Bike Pump Fittings?
Posted by MindWarrior on 08 June 2010 - 05:52 PM in Modifications
The bike pump
Product description: 6063 aluminum barrel with two tone T handle for better grip. 7" alloy barrel with dual action pumping for higher efficiency. Reversible Schrader/Presta thumblock. 120 psi.
I was wondering if there are any specific brass fittings that can be used on this pump for 1/4 or 3/16 ID vinyl tubing?
EDIT: Sorry, Meant 1/4 Outer diamter and 1/8 Inner diameter.
#277199 Bike Pump Fittings?
Posted by MindWarrior on 08 June 2010 - 09:13 PM in Modifications
EDIT: Shit, I meant 1/4 OUTER diameter, and 1/8 Inner diameter.
#277788 Bike Pump Fittings?
Posted by MindWarrior on 15 June 2010 - 09:29 AM in Modifications
#277218 Bike Pump Fittings?
Posted by MindWarrior on 09 June 2010 - 12:37 AM in Modifications
#275299 Angel Breech Catching Issue
Posted by MindWarrior on 19 May 2010 - 12:18 PM in Modifications
EDIT: For what SGnerf said above me, you could also reinforce your boltsled to prevent bending, I've seen some people use pieces from a coat hanger or Carbon fiber to reinforce them.
#270298 At3k Tank Replacement
Posted by MindWarrior on 25 March 2010 - 02:54 PM in General Nerf
Have you tried using dual action pumps? Should cut your number of pumps down quite a bit a, You can definitely fit a pump like that in an At3K.The AT3K can easily fit a small bladder in the rear cylindrical "stock" on the back of the gun. I've done it to one of mine. A cut down RF20 or Magstrike bladder will work, but you must band it heavily or you won't get very good ranges, 70' at best.
To make sure the air doesn't leak out all at once, you'll have to limit it somehow or put a valve in between the tank and bladder. The RF20 / Magstrike trigger works. I wanted it to refill "automatically" so I plugged the air output on the bladder with epoxy, and then poked a needle through it before it hardened. The result was an airtank that refilled in about 2-3 seconds, and the cool part is the liquid gauge shows when it is full.
Be aware that you won't be able to get all six shots off unless you lengthen the back stock somehow. I glued two AT3K stocks together to lengthen the chamber and put an entire RF20 bladder in there. I can hold 9 shots now but it takes like 50 pumps.
#264517 Sonic Bazooka, Micros And Megas
Posted by MindWarrior on 06 February 2010 - 05:45 PM in Modifications
#267509 Auto Vacuum Loading Tagger Gun
Posted by MindWarrior on 01 March 2010 - 07:04 PM in Homemades
#269511 Nf Plunger Assembly Problem
Posted by MindWarrior on 18 March 2010 - 11:29 AM in Modifications
#265254 Happy Chinese New Years(eve)
Posted by MindWarrior on 13 February 2010 - 05:51 PM in Off Topic
#272640 The At2k Turret "gear"
Posted by MindWarrior on 18 April 2010 - 11:15 PM in Modifications
Pics (taken from RyanMc#s rearloading AT2K Thread:
Its the center gear between the barrel stubs with a wavy-like pattern.
#273595 So Yeah
Posted by MindWarrior on 28 April 2010 - 03:28 AM in Off Topic
#276222 Shot Blast Airtank
Posted by MindWarrior on 28 May 2010 - 02:59 AM in Modifications
Pic taken from Bob's Nerfhq thread:
#281774 Help On Solvent Welding On An At2k Turret
Posted by MindWarrior on 01 August 2010 - 03:00 PM in Modifications
#276349 Shot Blast Airtank
Posted by MindWarrior on 29 May 2010 - 03:32 PM in Modifications
- NerfHaven
- → MindWarrior's Content
- Terms of Service and Privacy Policy
- Code of Conduct ·