Jump to content


Photo

Auto Vacuum Loading Tagger Gun


4 replies to this topic

#1 KaneTheMediocre

KaneTheMediocre

    Belligerent Asshole

  • Members
  • 613 posts

Posted 01 March 2010 - 08:08 AM

So, a few people have asked for a writeup on the autoloader at the end of my youtube vid:



I don't think that it's particularly wise to recreate this, as it is rather complicated, and very picky about the darts you put in it --malformed taggers can get stuck in the magazine, causing misfires. Also, if the plunger is held down for long after firing, an extra dart can fall into the breech area, and cause a jam. There is no reason to hold the plunger down after firing, but for some reason it's my natural instinct. Both of these problems are usually solved simply by firing the gun a few times, but it's still far from a reliable weapon. I understand that it's cool to have a semi-auto nerf gun that shoots taggers. I also think that it's probably the best combination of range and ROF available for tagger darts, but that's kind of like being the coolest kid on the short bus. Anyways, here are the basics of how it works and how it's put together


Posted Image

The HAMP motion is used to open the breech, and is mechanically linked by PEX tubes inside PVC tubes. A rubber band returns the breech to the closed position. This requires a low friction seal between the magazine and barrel breeches, and the breech covers. I know of no readily available material that does this on EMT as shown here--These were made from some Walgreens blowgun toys I bought a few years ago on a roadtrip. Rarely, thinwall PVC will be loose enough to slide freely. A steel pin connects the bottom (barrel) breech cover to the PEX tube, and the top (magazine) breech is simply taped to the bottom breech.

Posted Image

In order to get a dart above the breech in the magazine, all of the darts in the magazine are sucked back by pulling out the plunger. In order to prevent the darts from being blown out of the magazine by pushing in the plunger, a fairly high airflow one way (check) valve is used. It was salvaged from an REI marshmallow gun, but I know know how to make a high airflow check valve with a PVC connectors, and some cut up rubber sheet. In order to prevent the air from being sucked in through the barrel (which would prevent the magazine from functioning), the next dart in the chamber seals the barrel fairly well, and is held from being sucked further back by the breech cover pin. This DOES mean that the magazine has trouble loading the next dart, when there is no dart in the chamber, so one misfire usually leads to a few more before a dart drops in.


The barrels are EMT steel tubing, the clear dart-retention cover is from a plastic spinach box, and the rest is PVC connectors, duct tape, and a HAMP, which you can find here:

http://nerfhaven.com...showtopic=18962

And here's a couple more pics showing the breech and plunger, in open and closed positions:

Open breech, plunger in:

Posted Image

Posted Image

Closed breech, plunger out:

Posted Image

Posted Image

Edited by KaneTheMediocre, 01 March 2010 - 08:10 AM.

  • 0
RAINBOW CLAN FTW
I'm Purple

My Half-Baked MHA Site

#2 MindWarrior

MindWarrior

    Member

  • Members
  • 152 posts

Posted 01 March 2010 - 07:04 PM

I'm surprised nobody has commented yet. I really like this, and how it employs simple concepts together to make this. Ingeniou yet simple. Looking forward to building one of these!
  • 0
QUOTE(Ryan201821 @ Jan 2 2010, 03:20 PM) View Post

Seriously, no penis pumps or dildos on your Nerf blasters.

REVOLUTION BABY!

#3 wardrive

wardrive

    Member

  • Members
  • 66 posts

Posted 09 March 2010 - 09:19 PM

I saw the Youtube video, I really liked the durability factor. No springs, no triggers, no air pressure...
I do a lot of running at my most of my wars so I'm curious how they handle?
  • 0
It's not called incompetence, We call it Leadership.

#4 KaneTheMediocre

KaneTheMediocre

    Belligerent Asshole

  • Members
  • 613 posts

Posted 09 March 2010 - 10:52 PM

I saw the Youtube video, I really liked the durability factor. No springs, no triggers, no air pressure...
I do a lot of running at my most of my wars so I'm curious how they handle?


Most of my HAMPs could be drop-kicked off a cliff and survive. One was left out in a forest preserve for a month, during spring, where it was rained on every other day. Once the mud and bugs were shot out of the barrel, it worked, but never with quite the efficiency it originally had. The autoloader is probably the least durable due to it's complexity, and I suspect the first part to break will be the rubber bands.
  • 0
RAINBOW CLAN FTW
I'm Purple

My Half-Baked MHA Site

#5 durka durka

durka durka

    Member

  • Members
  • 364 posts

Posted 10 March 2010 - 12:59 PM

Thanks for posting this. This gave me some ideas to apply to my newly constructed HAMP. It's the basic build right now, but I'm working on shortening the loading process like this autoloader.
  • 0
"The warrior who cultivates his mind polishes his arms"


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users