Jump to content

  2. → Viewing Profile: Posts: Shadow the HellJumper

Shadow the HellJumper

Member Since 17 May 2011
Offline Last Active Nov 25 2015 01:04 PM

Posts I've Made

In Topic: Nerf Centurion - Streamline/elite conversion

07 October 2013 - 03:52 PM

I'm glad this kit is out since it's a step in the right direction. But I would rather have a full blown parts replacement kit that has a direct plunger setup and a full smooth bore barrel similar to the setup that Remedy Metal had going. Because to be honest, if this thing doesn't have some sort of full seal breech that also has a nice long barrel to make this thing accurate like a loser platform should be, then what's the real point other than having the most unwieldy and uncomfortable blaster in Nerf history? Plus, I'm not sure if using Elites was the best idea since they are just as inaccurate as streamlines; unless you are using CDDT's or those PAK Desgins darts or of course mad heavy Stefans.....

In Topic: Nerf Mega Centurion Mod

09 August 2013 - 05:07 PM

If I hadn't already bought two of these I would've held off. And I wish this would have come out sooner, because it took me 90 mins to figure everything out explained in this thread. But nice job dude. I just wish they would sell individual clips/magazines since the blaster only comes with one. Now all we need is for someone to figure out how to strengthen the darts up.

In Topic: Nerf Elite Mega Centurion - Preview and Internals

23 June 2013 - 11:27 PM

Reading all the info about this killed my boner....

Reverse plunger? Seriously Nerf?!?!?!?! Haven't we endured enough? And its not only that, but you put fucking SLOTS in the plunger tube?! I was really hoping that Nerf had pulled their heads out of their asses but it turns out we were wrong... Will not be buying this because fixing the issues would be too expensive and time consuming...

In Topic: Nerf Elite Strongarm Clip Mod

11 March 2013 - 10:16 PM

Yeah it's a total of maybe half a centimeter of difference, and it doesn't really need "fixing". I looked at removing it and the turret doesn't come out any further by trimming that piece so there was no point. So yes it technically is "uneven" but I don't think it's anything significant.


Exactly. So it's only truly necessary if you are just VERY OCD about it.

In Topic: Nerf Elite Strongarm Clip Mod

11 March 2013 - 04:41 PM

How hard is it to prime with the 6kg spring? I found it crazy hard, really easy for the priming mech to not catch the plunger, too.


Priming it is a little tricky but manageable. It almost feels like priming an NF with a [k26] equivalent. As for the catch, it catches just fine, no slip ups yet. I did a firing test of 18 shots and the catch held up.

Sweet mod, I will definitely do it once I get another Strongarm. Is this mod detrimental to ranges at all?

Cutting the corner off of the front piece is very helpful, I did 481IceDragon's mod to make the turret drop out more and the turret dropped out unevenly. I cut the front part as you described and now the turret comes out level. Thanks for the guide, good luck with the mod contest!


The only thing this mod affects is how you can load it and how many loaded darts you can carry at one time.

If you followed it correctly it wouldn't have dropped out unevenly..


Unfortunately I will have to correct you. if you noticed that the rear grey piece has a indentation that the front grey piece does not, which is why the turret comes out unevenly; the rear grey piece can open out further than the front piece, by cutting in the same indentation on the front piece, this allows the front grey piece to open out as far as the rear grey piece. hopefully if you review my pics it will be a bit clearer.

  1. NerfHaven
  2. → Viewing Profile: Posts: Shadow the HellJumper
  3. Terms of Service and Privacy Policy
  4. Code of Conduct ·