5162 replies to this topic

[T-REX]

1st post! Hoping I posted the images right.....
My BBB/Tetra Strike, because this site needs more blatant rif-offs of the Guru. Ranges are about 80'-85' with the BBB(Essentialy coupled and with a stock+NF spring combo) and the Tetra Strike is stock (i.e. 15'-ish) I play in wars usually only inclusive of stock ammo soI don't need amazing range.
"Rex Bow"? Name suggestions welcome ......

Edited by T-REX, 05 January 2011 - 11:45 AM.

[Scooter1]

Rear loading 2K, with six inch barrels, because I ran out of PETG.




A ball shooting Cobra. Shoots a single Target foam practice golf ball out of 1.5” PVC barrel about 45’ flat, but oddly enough, if I load two golf balls in it, it fires the front most golf ball 55’-60’.


Modified PAS, shoots about 100’ and has a lot of stuff done to it that you probably don’t care about.


Here is a WIP project, a rear-loading FireFly. I didn’t take pictures along the way, so I’ll probably never make a write up. As of right now, the turret seal is pretty poor; I had to remove the stock spring-loaded turret seal and replace it with a piece of foam, because of the widened holes at the barrel’s base for rear-loading.

Here’s a closer view of the rear-loading slot.

Here’s a view of the turret itself, with a view of the foam used for turret seal behind the turret (I ran out of barrel material, another reason I haven’t pursued this further).
Feel free to steal this idea and make a write up.

[RVMVTVProductions]

Man... its been a LONG time. Nice to be back into the Nerf Scene.

Useful Arsenal (whole shot)

The Primaries are leaned up on my wall, and their corresponding sidearms are on the floor.

The Maverick needs no picture:
It has an AR removal, increased seal using an AR spring, and the cylinder pops out a bit further. Nothing special.


Bagsfinder. I got it used and in a state of... oldness at Geddon '09. I finally got around to couplering it.
Has 1st Gen spring, Cpvc coupler, and a minimization. Nothing big.


The Paintball-ammo cylinder clip from the Pistol Splat Magnums makes for a nice belt hook. Someone else should try it; I took it on a morning run to see how many times it fell. It didn't (for me, at least).


Red BBB; I kinda messed up on couplering this, so the plunger stop isn't present.
Other than that, it has plunger padding, increased seal, new lube, CPVC 3/4 to 1/2 coupler, an Everbuilt spring, and an extra catch and trigger spring to accommodate for it.


Christmas gift: a Predator Magnum. CPVC couplered. nothing much, but I really like Pistol Splats and their variants.


Barrel is straightened by the use of an LSFG Front Barrel jammed into the orange muzzle.

[Pic spacefiller]
Here's one VERY useful tip for reassembling a Magnum. There are two screws connected to the metal priming rod section of the lever action. Unscrew it before reassembling. Then, halfway prime it (there are two sections on the plunger "rod") and screw it back on. Incredibly helpful and shortened reassembly time from 10 minutes to 2 minutes.


I know these pics aren't the best, but they should do....

EDIT: Oh yeah, I am in need of Orange Tape; the E -Tape being black isn't the safest thing in the world.

Edited by RVMVTVProductions, 06 January 2011 - 11:18 PM.

[pjotrkuh]

I built an RSCB..... out of copper 'n' brass........Shall I dare to call it a PRSCB?....

[random11mason]

I've decided to forfeit my right to post in these forums via a display of my illiteracy. I will no longer post in this thread without posting my own original image of a modified or painted nerf gun....because I'm banned.

[c0rrupt10n]

my first LS mod

Edited by c0rrupt10n, 09 January 2011 - 09:51 PM.

[NimbleFellow]

Old Primary/Secondary


New Primary/Secondary

[louiec3]

I painted it clear. Lucian told me how.

[cheyner]

Joined the 2k club.

Standard stuff done.

Iron Man SS

Everything done should be pretty obvious.

PAS


Warthog

17/32 Brass barrels.

[Kid Flash]

BigDTG? I need to get a pump in there somehow (suggestions are more than welcome) and then I need to toss some barrels on there. I might just toss the stock turret on there for now though. I expect some pretty good ranges, and roboman told me a hornet blast button wouldn't fit. I proved him wrong. I think this will be primary worthy once it's done.

[BritNerfMogul]

That's it man, game over man, game over!



WIP Pulse Rifle

@Kid Flash - I say call it the BlastCannon

[Kid Flash]

Update on the BlastCannon.

done:


quick slip connector, so that i can attach a pump/pvc tank/hpa rig:


holes where the tubing comes out are pretty clean:


EDIT:

well, last night I decided (with the encouragement of TaerKitty) to build my SalvoFly, BigFly, FireSalvo, etc (I personally like SalvoFly the most).

Edited by Kid Flash, 12 January 2011 - 07:01 AM.

[BritNerfMogul]

Winchester 1887/ RFR to come soon...

[Kid Flash]

A little update... Should have this finished later today, since I can't sleep and I just found some tubing.




Since I took these pictures, I have changed the tubing location around a little, and added a piece of plastic to the priming bar. I will be posting final internals later, when this is finished. Once this is done, I will start working more on my MS bladder backpack. I just need to buy some 4 inch PVC and 4 endcaps to go along with it. The backpack will be using 2 MS bladders, unless I don't get a good amount of shots off, in which case I will be adding another.

[Lucian]

What do you do when your retarded neighbor wants to get his Tacti-cool on? YOU GIVE HIM WHAT HE WANTS.






Lulz.

[thedom21]

My first post here


First up my WIP primary. I still need to put a breech on the ls. IT is a LS firefly integration. I got both at a thrift store for a combined total of 3.50






My current primary,






My stampede with an ar removal and an AT2K inside a recon laser light with a recon handle.










My raider,



My PETG sspb



My nf,



My crossfire



And where it all happened

[thesoxfan1234]

Picture troubles. Please delete. Sorry.

Edited by thesoxfan1234, 16 January 2011 - 12:36 PM.

[LT DAN ICE CREAM]

First modification, based off of ahtanie's Recon/Big Salvo modification. (olol NREV.)







Big Salvo tank, hell yeah.

[Salindin Naz]

Here's a Lancer I did as a commission piece for a fellow member here at the Haven.

[Jtest]

RSCB PAS used for a post apocalyptic larp.

Edited by Jtest, 16 January 2011 - 08:48 PM.

[iDrag0m1r]

PAS balls fit nicely in 1.5 PVC



Even with a ton of deadspace its shooting 35 feet.



Finally got around to AR modding my Stampede

[mysterio]

Nerf on Buzz Bee Action.

[Lucian]

Coming soon to a reality near you:

[utahnerf]

Ultimate Missile Blast, PVC couplered, pump plugged. Picked this up at Target today for $10. The tank is very interesting, it's larger than a Mega Missile tank, but smaller than a BBBB tank. Achieves 115' flat with a 5 dart hopper with a 13" Sch. 80 barrel and 7 pumps. Damn straight homie.

Edited by utahnerf, 17 January 2011 - 10:47 PM.

[durka durka]

A little something I'm working on:


The glue is still drying, so I haven't tested this yet. Note the coupler glued into the follower. The coupler is pushed back onto a 1/2" cpvc barrel to allow the use of 1/2" cpvc barrel attachments.

A QUICK EDIT: Obviously there's a lot of deadspace in this thing. The titan only has enough output to launch the balls about 25-15 ft. I'm going to have to do a tank expansion, most likely using the tubing for the "pressure gauge".

Edited by durka durka, 19 January 2011 - 07:51 PM.