5162 replies to this topic

[Twitch]

This thread needs more pictures of mod'ed guns.

My RF20: The Ruckus
That's an air compressor attached to the back. After making extra drums for darts, and modifying the blaster so I can easily load the gun, I wanted a way to easily fill the bladder. The thing can go from completely empty to fully loaded and primed in just under 8 seconds. (great for the zombie-games).







I've spliced the compressor into the stock tubing, so I can still use the manual pump if the battery dies in the middle of the games.



After the holidays are over and I have a bit more disposable income, I'm going to ditch the air compressor in place of a 3000psi air tank (Thank you Forsaken_Angel24 for the idea.) and splice a 2nd RF20 after the regulator, so I can dual-wield the beasts. (Thanks to CaptainSlug for this idea.)






And my next "integration." This is just the prototype; if I find it manageable enough, I'm going to replace the zip-ties with various bolts and mechanical fasteners so I can disassemble the gun for easier transport. Each gun will be panted a single color, and it shall be named Voltron.











Yeah, I know Voltron was only 5, but I figure the At3k counts as the sword....

Edited by Twitch, 14 December 2007 - 01:28 PM.

[penguin807]

Twitch, those two Nerf guns are simultaneously the funniest and most terrifying things on the planet.


My Maxshot. It needs some touch-ups on the paint, but it'll have to wait until spring, as it is far from good painting weather here.



It has a PEX barrel, and shoots modified stock darts (I forget what they're called) about 90ft flat.

And yes, I know my barrel is too short.

Edited by penguin807, 17 January 2008 - 10:43 PM.

[Xinion]

Ok first this is my BBB. Its b00m13's version of Angel's clip/breach mod.
And Im soon going to give it a silver/black paintjob
*and No the trumpet is not part of the mod



Next is my NF. I need to shorten the barrel.

Edited by Xinion, 14 December 2007 - 08:49 PM.

[xNFx 37]

http://img209.images.../img6090zn5.jpg

That's my first 3K. It Kicks ass.

http://img204.images.../img6092fa8.jpg

That's my first and only paintjob. I think it sucks but...

http://img204.images.../img6094ro3.jpg

And finally my coupler'd NF.

I do have at LEAST 10 more guns. 2 are being re-modded (BBB, First shot) and the rest I was too lazy to put up

Edited by xNFx 37, 15 December 2007 - 05:54 PM.

[Twitch]

Thank you all for the compliments. To answer some questions, cocking the BBB is no different than otherwise
and I hold it pretty much the same way as a normal BBB, except holding a magstrike handle instead of the Bow's foregrip.


The BBB at rest

and primed

The handle of the BBB slides right between the tank-shells of the magstrikes.
While it's not really heavy, it gets tiresome hauling the thing around for four hours, holding it at shoulder height. To fix this problem I'm constructing a wheeled tripod to hold it, so I just push it around the hallways like a mobile artillery installation.

I can even carry The Ruckus along, if so inclined.

The shoulder strap lets it hang right at my waist, so all I have to do is drop my hand to the trigger.


I have decided upon a paint job; each gun will be painted a single color (black, red, green, blue, and yellow) in honor of it's name: Voltron.


As for my inspiration....well,

may have been involved.


And lastly, the sight that seems to send all the tyros running.



Thanks again, and sorry for kinda hi-jacking such a large portion of the page, and if the pictures are blurry/large, et cetera.

[joeyaglr444]

You thought the other one was sexy.

Edited by joeyaglr444, 17 December 2007 - 06:40 PM.

[Maeric]

Here is my contribution. My newly painted Longshot intalled with an Angel Breech, two stephan compatible clips, and an after-barrel.

Edited by Maeric, 21 September 2008 - 01:54 PM.

[DeceitfulSteve]

And by the way, that little turtle mod thing on there, not my fault, my little kid brother drew that on there. The worst part is, he drew it in purple sharpie!

I've heard rubbing alcohol and nail polish remover will get permanent marker off plastic. People have suggested both acetone and non-acetone nail polish removers, but I've never had to use either.

Whatever you decide to try, it might be a good idea to do a spot check before you attack the permanent marker, but I imagine the plastic these guns are made of will stand up to any of those three options.

[One Man Clan]

I should ban at least 3 people in this topic. Instead I just opted to delete their useless posts. Use this thread for what it is.

DO NOT QUOTE USELESS SHIT IN HERE (or anywhere for that matter).

[penguin807]

Maeric, that's a nice paintjob. I usually don't like cut down Longshots, but yours is nice.

I painted this one at night (Who could tell?). It's an old picture though. I got rid of the front part of the scope and the foregrip, and gave it a decent barrel a while back.



Edit: fixed the link (not like anybody noticed though).

Edited by penguin807, 19 December 2007 - 11:11 PM.

[dadude778]

This was my first paint job but my friend took it to a war so it got beat up. basic ar removal with cpvc coupler and I glued the ammo holders to the bottom.

I use this "clip" like thing thing

I don't know where I saw it or what it is called but I like it

Over all it was my first mod it gets about 70' and thats with luck
accuratley its about 55'

[precisionnerfer]

My version of an arrowstorm:

I had it in a sale thread, but might as well stick it here.

Edited by precisionnerfer, 20 December 2007 - 11:16 AM.

[Anima]

A commission I took recently for a steampunk Nerf gun.









The alchemic injector assembly screws off for easier carrying. Air restrictors removed, Russian Roulette mod completed.

[angelof DEATH182]

A commission I took recently for a steampunk Nerf gun.



The alchemic injector assembly screws off for easier carrying. Air restrictors removed, Russian Roulette mod completed.

The left half looks just plain awesome, But the back half of the above pic could use a touch-up or maybe even a complete repaint, But other then that i like it.

[bobafan]

This is my first paintjob, and I think I did fairly well.







The worse side


front


It is supposed to look like there are water droplets on it.
The mod. The only thing I did differently was to use a piece of sintra plastic to cover up the hole in the front instead of hot glue.

[penguin807]

Holy raindrop looking NF batman! That's a very nice paintjob, especially for your first.

My scout. Not the prettiest thing on earth, but it gets the job done.



I wonder if anybody has realized that I only have 2 kinds of paint...

Edited by penguin807, 17 January 2008 - 10:42 PM.

[sn1per]

I guess i'll finally throw some stuff up here...


My crappy old tek 10


My custom NF



What you see before you get shot my me


what i see before you get shot by me


My TTG (yes, it's just a shell)


My mav (AR removed, screwed up barrel release thing)


Awesome angle view of my mav


and thats about it for now!

EDIT:Sorry for the random sizes again...

Edited by sn1per, 22 December 2007 - 04:06 PM.

[BustaNinja]

cool, but let's keep these types of posts to the minimum, okay?

Do you acctually post pictures in here, or just get your underware in a bunch? Stop the backseat modderating, I know this sounds hipocritical but really. It annoys people.

So this post isn't useless

Behold my second paint job. My minimized and completely screwed Firefly. It sucked when I got it and that didn't change. I learned a valuble leson about painting, You really need to paint the whole thing. Covering part of it with tape leads to a bad paintjob. Cover the whole thing in paint then touch up with other colors.

[bobafan]

I've been asked how I got the water droplets, so here ya go.

I used a technique I saw on the show "how it's made" to make the droplets. You basicly paint the base layers, then spray on some water from a spray bottle. After that, lightly mist the piece with white. The paint will be collected in the droplets and flow to the bottom of each drop, because paint is heavier than water. After that, put the piece near a heat source and wait for the water to dry.
Voila! water droplets.

Edited by bobafan, 23 December 2007 - 01:06 AM.

[keef]

My titan from Ebay bought NIB.
Its a CPVC breech, and has the pump plugged, firing pin fixed, and the tilt things removed. Gets 140 feet+ with a streamline with a BB in it.


My titan missle has a 1" PVC endcap duck taped on. I shot a box and it DESTROYED it. Gets 60 feet with 20 pumps.



My SS2. Everyone says the valve is "finicky" but mine is PERFECT. Has a plugged pump too.I can pump it 28 times and shoot through 2 sides of a box. OMC's PETG with etape around it to fit at2k pump tube. Gets around 100 feet with taggers at 12 pumps.



Edit: SS2 is plugged, and please excuse the foot and the retainers.

Edited by keef, 23 December 2007 - 09:38 PM.

[Wisey]

This is my first paintjob, and I think I did fairly well.

Thats a pretty f**king cool paintjob. How did you do it?


This is my first post in this topic, and I'd just thought I'd share some of my friends paintjobs (I can never be arsed to paint guns, just mod them. Plus, I'm rubbish at painting).







I think the NF is the best by far out of them all, but the Fireflys pretty cool too. As for mods;
*Longshot - intergrated side arm, AR's removed, NF spring and a locked stock.
*Firefly - AR's removed
*Brown NF - AR's removed, very nice spring replacement (bought modded from ebay..)
*Gray/Black/Red/Green NF - AR's removed, laser sight partical removed, half a gate bolt spring replacement and banding

EDIT: I've just noticed the darts in the NF XD need to take them out before the get miss-shaped.

Edited by Wisey!, 24 December 2007 - 08:54 AM.

[n-strike]

This is my minimized CPVC coupler modded Big Blast.

[Thomas]

Well, I have acumulated a fair amount of guns over the course of...4 months? I haven't modded a few, so I'm leaving them out. Here's like, 7 of my guns.

Shell of a LnL


First primary, my LBB


This little guy got me thinking about modding. My Hidden Shot.


my twin At3ks


Modded at2k


Arctic Shoc, super soaker conversion. Decent range, about 80 ft. Gave it to my brother as a christmas present


Sharpied up, minimized NF. PETG barrel




Sorry if the pics are oversized, if they are I'll get to fixing them immediately.

[Blasphemy]

I found a Max Shot at my local Ocean State Job Lot for $9.99. I snatched it up, relubed it and slapped a coupler on there:

Soon to have a 12" CPVC speedloader once I make a trip to Lowes in order to get more of the stuff.