Modification and Paintjob Pictures
Posted 16 December 2014 - 06:28 AM
next is the DTB which is phase one integrated into the long shot it also has a spring replacement and a 1/2" cpvc barrel replacement.
Posted 18 December 2014 - 07:32 PM
1/2" CPVC barrel (obviously)
New catch spring (from the clip retainer in the stock of my LS)
dremd out the catch slot on the bolt
Spring replacement (includes stock spring a vulcan spring and a random spring i had laying around)
Im going to give this gun to my little brother for x-mas along with a singled LS that i will post soon.
Posted 24 December 2014 - 04:34 PM
Posted 26 December 2014 - 04:19 PM
LPL (Lock Panther Load):
Work in progress. The pump shaft on the back of the LBB tank is almost the exact diameter of the pass-through hole for the turret system on the Mad Hornet:
Unholy Three: DUPLUM SCRTA, DUPLUM PROBLEMA (2009)
But Zeke guns tend to be like proofs by contradiction
Theoretically solid but actually non-constructive
Posted 28 December 2014 - 06:47 PM
As far as I know the first Nerfed-Boom Co. Blaster. I introduce you to the Nerf Farshot.
Mods I have done to it are:
Replaced the barrel with Cpvc, and then some
Added a barrel extension thing just because I can(not recommended unless you have a spectre barrel)
Integrated a nerf handle on to it (Because I am like 5'10-ish, the handle was comfortable, but too small for me)(I used a demolisher handle for this.)
Nerf rail added, Going to add another on the other.)
Tech Target Spring added(And originally I had a spring I salvaged off of a party popper, Kind of a spring hoarder when it comes to this stuff)
And priming handle removed, but replaced with a keyring.(not shown but I later added some E-tape for some comfortability when I prime it)
A Demolisher rocket launcher That was comepletely rebarreled for any micros, I give you the "Rockin-launcher"
Mods I did to it are:
Cpvc Barel replacement
Silver and Gold Paintjob(made it look sort of rusted on the handle, with some silver accenting in the divets)
Mods need to be done:
Cpvc Elbow, to make firing the thing less akward
I know. I was just busting your Muttonchops. It's just what I do.
Posted 01 January 2015 - 09:49 AM
The Maverick has dropout mod, AR removal, and a few pennies behind the spring.
The Stryfe has some RM2 motors, a 2s lipo in the jam door, and completely re-wired.
This is my current project. It's a Lanard First Shot. I re-barreled it with cpvc, improved the seal on the o-ring, and it shoots 70ft flat pretty easily with elites (I don't have any steffans, but hopefully that'll change soonish) It will be mostly silver, with neon green accents and tip to make it look like an alien blaster.
I've got a lot more on the way.
Posted 04 January 2015 - 10:40 AM
LED lights up when primed. Then goes out when fired.
The tactical switch is actived by the the rotating turret mechanism.
The turret has had the barrel pins removed and back cut out for rear reloading. Also I cut the side of the turret off to expose the barrels.
The trigger has been cut out just for aesthetics.
Side by side with my stock strongarm.
All logos have been removed along with the loop/strap things on the bottom and back of the gun.
I went with bright green and black with sliver rubb n buff on the paintjob.
And here's my jolt I did at the same time.
I changed the spring for a tex 6 spring I love this little blaster.
I've left the AR alone on these two Im not sure if I should do it. Some say it's better some say it's worse. I just don't know
Edited by Joey Skylark, 04 January 2015 - 10:45 AM.
Posted 07 January 2015 - 11:40 AM
so obviously the AT3K is singled but what i find unique is that i have replaced the original pump (leaving it intact) and put in a bycical pump now I know meany people have done this but i have yet to see someone intagrate a big blast into the the side of the gun and it is powered by the original AT3K pump and i used a long shot charging handle held in with epoxy putty to prime it.
Edited by pwr1, 07 January 2015 - 11:42 AM.
Posted 09 January 2015 - 07:28 PM
Posted 18 January 2015 - 01:57 AM
I decided id make him a nice one x3
After purchasing a couple of second hand guns i went to work and ended with this
(This is my first attempt ever xD so it may be a tad rough )
-Air restrictor removal and Bleed hole cover
-secondary mainspring added (from another nerf gun)
For those who like distances best i can say is that it shoots about as faf as a stock 07 recon (thats with the loser barrel on, im too scared to pull it off xD
Edited by Xene451, 27 January 2015 - 09:25 PM.
Posted 19 January 2015 - 06:48 PM
Posted 23 January 2015 - 08:39 PM
The purple connector piece is a BIC pen cap.
Nothing crazy, but first mod in 5+ years for me. Feels good getting back into it
Posted 27 January 2015 - 11:45 PM
Name: Barbecue Chicken
Mods Done: Level 4 modifications; Priming bar reinforced, spring rest reinforced, catch reinforced, rebarreled with a setup that allows me to use mega and elite darts via 1/2" cpvc and 3/4" cpvc couplers.
Integrations: N/A At this time; Splitfire (much wow, very original) and AT3k planned.
Comments: Found this baby on eBay and I finally had some cash on me, much to the wife's dismay. I didn't touch her for a while, wanting to keep it pristine and stock (she only had a small crack in the bow arms and was missing the bowstring when I found her) as long as possible. I finally started attending some weekly wars and decided I needed to bust her out and spruce her up. First couple wars, she stayed stock; using only a 1/2" cpvc barrel for elites e-taped and crammed into her original barrel. The week after, I decided I needed to actually bring her up to standards.
After fixing her up, I'm quite pleased and plan on completely gutting her internals and doing a full custom set so she's perfect. Needs a little more reinforcing at that point, but that'll come whenever the internals do.
As for the name, I go by Coleslaw at my wars. I figured, "Hey, what goes great with coleslaw? Barbecue chicken!" and so the name was born and embedded into her heart. Now all she needs is a couple secondary pistols (Forky and Spoony) to complete the set.
Posted 28 January 2015 - 09:51 AM
Posted 07 February 2015 - 01:53 AM
Posted 14 February 2015 - 06:35 PM
ps: first post =p
Edited by dialga949, 14 February 2015 - 06:36 PM.
Posted 19 February 2015 - 12:59 AM
Edited by Xenon131, 19 February 2015 - 01:07 AM.
Posted 28 February 2015 - 03:57 AM
Posted 07 March 2015 - 03:03 PM
It is Complete to MY standards, which incude:
Mega to micro Conversion (with CPVC)
Various Spring Additions, which I finally settled on an OMW 5KG Retaliator Spring. (just because I didn't feel like buying an EAT, Rampage, or Retaliator just for their springs.)
tweeking the catch with a shortened OMW catch Spring
and Skeletonize the barrels
and Lock Removals
There was one problem when I modded it though. The first time I modded it, I thought a certain white piece on the prime was a lock, so I took it out. After I did that, It wouldn't rotate consistently. So after a couple of hours of trying to fix it, after I lost that piece, I got pissed and Just decided to open that part up, and goop it in place.
And while I was at it with the goop, I just reinforced the rotation mech.
Sorry for the last pic being bad. Had a cell phone the whole time taking these pictures.
right now, in unnoficial ranges, the farthest it shot a hotglued Elite was somewhere between 200-300 Feet at the biggest angle I could maximize the shot. on a level shot, again, unnoficial, It reached 150-ish feet.
I know. I was just busting your Muttonchops. It's just what I do.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users