5162 replies to this topic

[Puppylayer]

Sorry for the post w/o pic, but I do have a question that is intrigueing me...

BlackSunshine- for the viper, I am intrigued as to how you painted the "skin". Did you, by chance, use some sort of net?

Thanks for the "No pic" tolerance,

-P§

[VACC]

No picture gets you a suspension. Honestly, how difficult would it have been to PM him?

Also, since you, apparently, were aware of the requirement, I'm not going to be overly lenient.

[smeagolsaur]

[Salindin Naz]

Hi again, just though I'd show you guys my recently finished Firefly, and my silly Recon barrel mod. That's if you can even call a few small cuts and some Plumbing Goop a mod. Hope y'all like .















Salindin

[serpent sniper]

Colors are a bit off from the flash.

[rokor]

The GNBK. I already posted the main thread, but I haven't posted much in this one so I might aswell.




EDIT: Wrong picture, haha.

Edited by rokor, 08 January 2009 - 09:01 PM.

[sputnik]

Latest rebirth of Hrothgar.

[bamblack2000]

Well here's something I recently finished.



Up close on front:


And the last thing you will see:

[koree]

The thread has been dead for a few days here so I thought I'd post something I made a while back.



Industrial Spring, better seal around the plunger, reinforced plunger, cushioned plunger, coupler attached so i could quickly swap out barrels, not for loading. (I only load from the top on nitefinders, its a secondary, if i want 100 feet I'll throw it at my target.) Also put some batteries in there to give it a better "feel."

Painted and attached one of my airsoft red dot sites for the picture. I get a consistent range.

Thanks for looking,

Koree

[Echnalaid]

Breaking in my new Dremel with this

PETG in the stock barrel, sorta. The plunger head was Dremeled to fit PETG, and then the top part of the barrel.

New Recon that was a late Christmas present. I don't have pictures of the internals, but the plunger tube is padded with foam, to not relive the horror of my last Recon's plunger tube's cap flying right off. The hole is e-Taped up, as was a hole I made during my hour of hammering the AR out.

And then here's my Quick Switch Clip mod.

[Coop]

My Firefly. This was mostly a test-run. It was my first attempt at hand painting. I think I did fairly well, but it could be cleaner.

[Renegademilitia15]

My latest barrel atatchment



6 in. barrels.

Ironically, the only thing it doesn't work well on is my couplered 2k.

[bensklm767]

1st post This is my first piece of work: a regular old nitefinder. I did add in some ideas of my own, though. Did the regular mods, used a marker nested barrel into a 3 1/2 inch aluminum barrel (all the store had).




added some ammo holders from an old, busted up firefly.



also added an old, gutted out LED flashlight part.



May not be the best, but hey, its the best I can do with a pathetic attempt at a True Value store.
Range: 69' flat average

[Jedijoe9]

Working on some decent loaner guns for wars. I had a busted longshot that I singled and frankly, I was suprised at how effective it is. For fun, I attached a drop-clip maverick to the front. Two other two guns are a RSCB at2k and a spiderman gun I bought from Lynx for $1.

[jerm78]

[Daniel Beaver]

Here are a few of my workable mods:



An SM750 integrated into an NF shell. I find this much more comfortable than the SM750 shell.




An NF with an AT2k integration. The NF has a new spring, a better O-Ring and an internal CPVC coupler. The AT2k has a PVC coupler, airflow mod and a plugged pump. The trigger fires both guns. The NF gets around 75'. I haven't range tested the AT2k. I thought about cutting down the pump, but I think its more practical with a full-sized pump (although it looks more silly).




My main primary and sidearm. Nothing too fancy here.

[Gas Mask Guy]

WIP pump-action Recon. I had 2 functional and 1 non-functional Recons, so I decided it was cobblin' time.



Note: the bottom is attached via an N-Strike fastener, so the whole thing will be removable.

[MrDelish]

I know it's kind of a repeat, but here's the Plasma Cutter with some finishing touches and a shiny overcoat:





plus a tech demo; the soundtrack is 100% original:

[Shrub]

Brassed 3K


Brassed Crossfire

Edited by Longshot Wielder, 16 January 2009 - 10:03 PM.

[Salindin Naz]

Here's another of my Recons. It was sitting in a box in my apartment, half painted and all sad and lonely looking, so I finished her off and felt like I should post it (so it didn't feel too left out).





That double mag looks a bit tacky, got a bit over-zealous with the glue, might have to give it a new one.


Salindin

Edited by Salindin_Naz, 17 January 2009 - 12:12 AM.

[Gears]

I want these to make it out to people who will mod and use them...

I wouldn't want to upset OMC now, would I?
-This entire mod was done without opening the gun.


I really wish I took pictures along the process and made a write-up. There is an extreme lack of SM(1/2)K mods.

Barrel setup was inspired by rawray7's crossbow coupler system.\


(Yes, the pump is crooked. I assume the previous owner was pretty rough with it)

Edited by Gears, 17 January 2009 - 05:46 PM.

[Merzlin]

Here's my Nitefinder

Mod's done:

• AR removal
• Spring Replacment (Ace #49)
• Catch Spring Addition
• PETG ammo holders (Battery Deposit+Front original holders)
• Cosmetic front IRON SIGHT.
• Goop'd PETG nested into 1/2" PVC for support barrel-4" to be exact
• TONS of dremeling work

EDIT-The barrel is slightly crooked..Will be fixed in version two.

Edited by Merzlin, 17 January 2009 - 10:25 PM.

[Salindin Naz]

Just finished off my Dart Attack Longshot sidearm integration. I did what Forsaken_Angel24 did with the fishing wire (I used a 0.017 gauge guitar string) tied to the main trigger, plus all the usual mods.




I did just a little dry-brushing on this one, just to spice it up a bit. Haven't gotten to the scope or clips yet, but they'll be coming along sometime.


Salindin

**edit** Crap. I see a few spots on it I never touched up. I'll post new pics when I finish.

Edited by Salindin_Naz, 18 January 2009 - 08:00 PM.

[Blacksunshine]

Fresh off the bench.




And yes you will find it on Ebay once I get around to making a video for it.

[jerm78]

The Professional 2K