Jump to content


Photo

Pump Action Reaper Writeup

Quick Cheap Easy

4 replies to this topic

#1 Snoop Doggy doge

Snoop Doggy doge

    Fig you, Van

  • Members
  • 500 posts
  • NerfHaven Subscription Supporter
  • State:New York
  • Country:United States
  • Snoop Doggy Doge on Youtube

Posted 23 September 2016 - 01:31 AM

Godfuckingsamnit NH add a failsafe for closed tabs. Got my writeup closed write before fucking posting, aghhh redoing it *sigh* ahhhhgggg.

T R I G G E R E D as fuck right now, I have so much #salt

"Alright, a pump action stock blaster that doesn't have your stupid recon/retaliator under pump this time Van!"
Well I wasn't even going to after reviewing it, (BTW notice it came up before NH is back post ;) hehe) but I had some 1/4 in PVC and I noticed it was really close to fitting in the front attachment. So I decided fuck it, lets do it. I have spent more time on this writeup than I have building this. 

Also, I didn't even need to open up the blaster past the top slide for this. You can do this to a stock reaper lol. Stock addition maybe. Aeromechs already bitching about it, he'll probably bitch about how I didn't countersink the screws or sand down the grip enough lol. Why am I writing this on a school night?

14407893_971819019607684_276844032_o.jpg

Yea bitch you know you want this. mmmm it'll cost ya like 30$. Photo description BELOW the photo as always.

 

 

WHAT YOU'LL NEED

Spoiler



STEPS
14408186_971818962941023_310423561_o.jpg
Alright so get that 1 in PVC.

14423794_971818949607691_1382253751_o.jpg
Take your grinding wheel and sand about an inch in so it can fit in the front of the reaper for a bit.
Look at all that privilege that's on my arm from dremeling!

14456736_971818956274357_1830107258_o.jpg
It should fit in like this and stick out.

14453874_971818959607690_1838593569_o.jpg
Now cut out a channel like this an inch wide. This is for clearance of the dart tooth

14456848_971818969607689_1830167853_o.jpg
Stick it in, pull the trigger and make sure the dart tooth is unaffected. The 1 in PVC should be like this, look down the barrel and pull the trigger and make sure it works. 
 

14408092_971818982941021_373707259_o.jpg
Now drill holes on both sides, and bolt it in. Make sure the screws don't affect or touch anything inside, look down the barrel again. Make sure the front barrel is at least 7 in from the front nozzle. 

14454081_971818986274354_1627156214_o.jpg
Also, cut out a segment of 1-1/4 PVC that you like gripping as it'll be your pump. It goes over 1 in PVC nicely and 3 in long is a nice pump. 

14339214_971818989607687_129289244_o.jpg
aight so like, get a strip of material like a foot long in a rectangle shape and than connect it from the front pump to slide. Drill, bolt together, sand down, make sure the screws are flush, yadda yadda yadda it's really simple and if you don't understand I can't help you. The arms should be like a foot long. 

14407893_971819019607684_276844032_o.jpg
Screw it all together. 
Boom. It's fucking good to go. Didn't even open it up entirely. 
This is like the most cheap war practical mod.


Overall, it's pretty cheap and should be decently war competitive. Last war I went to, this thing stock was pretty awesome. Now it's pump action and got ROF, I can add a stock so you get a full primary because everyone "Needs a stock" for some reason. I'll test this at the next war I go to, loan it and see, I expect to see other people building this because you really only need a drill screwdriver and sandpaper for this (yea yea sanding the front is a bitch but it works) so like, really easy noob primary. 

more tactical photos and review to be added later. 


Edited by Snoop Doggy doge, 02 October 2016 - 11:24 PM.

  • 0

#2 Snoop Doggy doge

Snoop Doggy doge

    Fig you, Van

  • Members
  • 500 posts
  • NerfHaven Subscription Supporter
  • State:New York
  • Country:United States
  • Snoop Doggy Doge on Youtube

Posted 23 September 2016 - 01:45 AM

this comment is RESERVED for future stuff, probably for adding a stock


  • 0

#3 jwasko

jwasko

    PowerBeard

  • Moderators
  • 1,021 posts
  • Location:Pittsburgh, PA
  • State:Pennsylvania
  • Country:United States

Posted 23 September 2016 - 10:01 AM

Nice work. Looks like a good blaster for beginners. Added to the directory.

You may want to type your writeup in something other than your browser (even notepad), then copy/paste. That's what I've always done.


Edited by jwasko, 23 September 2016 - 10:09 AM.

  • 0

-Jwasko, STILL Sole Surviving member of Steel City Nerf and Sober Sister of the Sex Dwarves
We NERF ON all day, and FUCK OFF all night


#4 Snoop Doggy doge

Snoop Doggy doge

    Fig you, Van

  • Members
  • 500 posts
  • NerfHaven Subscription Supporter
  • State:New York
  • Country:United States
  • Snoop Doggy Doge on Youtube

Posted 25 September 2016 - 12:54 AM

<3 thanks Jwasko! It's pretty decently powerful, though there's not much to do besides throw in a new spring, or removing the lock. 



Yea I might have to look into something but I don't want to forget a hyper link, and adding pics is just, *shudders* a horror  to get correct. 
It's 2016, Phil can't put in a "are you sure you want to leave NerfHaven?" thing when you're making a writeup?


  • 0

#5 Cartaya

Cartaya

    Member

  • Members
  • 112 posts

Posted 04 October 2016 - 09:42 PM

I think that PVC barrel will make a good housing for a sleeper breech barrel system later on, Good work man!


  • 0

....Fear of a Nerf Planet!




Also tagged with one or more of these keywords: Quick, Cheap, Easy

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users