Jump to content


THIRST

Member Since 28 Jun 2003
Offline Last Active Jun 28 2016 08:58 PM

Topics I've Started

Hinged Double Barrel Pump Action Shotgun

19 May 2009 - 05:55 PM

Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Action
2 Darts
4 Darts
6 Darts
8 Darts

2 Darts: 90 feet
4 Darts: 80 feet
6 Darts: 70 feet
8 Darts: 60 feet.

Theres variation among the dart ranges within each set, (ex. 6 darts: 1 got 93, 2 got 60ish, etc), but those are the averages. Every 2 darts added decreases range by 10 feet approxamately.

Noob Asking About Long Shot

22 September 2006 - 06:31 PM

Hey, I'm new around here so cut me some slack please...Sorry I couldnt search due to my excessive exhuastion...So how is the long shot in general, and how much does it cost?

Double Barrel Nf Writeup

06 April 2005 - 04:02 PM

I had this for awhile, found it floating around, so here you go.

Double Barrel NiteFinder Mod

Posted Image
This is the NiteFinder, its a good secondary, and there is a lot you can do with it. For $6, it's a must. This mod show you how to mod your NiteFinder to be double barreled. While it must have both barrels loaded to fire, it still gets 50-60 feet, and its damn intimidating to be shot at by a pistol tht shoots two shots eh? I made this mod because I thought it would be fun, but the gun itself turned out quite useful.
Posted Image
This is one of the air restrictors that you must keep, you can throw out the top one.
Posted Image
Cut two peices of 17/32 vinal tubing, about 1-2 inches each.
Posted Image
Take the air restrictor that you kept, and file, dremel, or cut it so its much wider, like this. The 2 peices of vinal you cut must fit in here, though leave as little room on the sides as possible, it makes your life easier.
Posted Image
Glue the two peices of vinal in the air restrictor...Load on the goop, and make sure its aritght. When this dries, just glue two brass/cpvc
barrels over it. You will find that its quite secure, no reinforcement is needed if you really goop it up.
Posted Image
A nifty trick Ninjz invented, wrap 3 layers of electrical tape around the plunger head. Despite any rumors you hear, it is in no way bad
for the gun, and makes it more air efficient. You will get better ranges doing this. An alternate way to do this is to get a sla fo small sized inner tube, and put it in the space where the o-ring goes, with the o-ring over it. I foun it to work even better than electrical tape, but its a matter of finding a small sized inner tube.
Posted Image
Close your gun all up, and you should have one beast of a gun.
Posted Image
Its intimidating to have such a small gun with two barrels. Its even more intimdating to know it performs. Its pretty accurate too, the velocity is as good as ever. I hope you enjoy!

THIRST

The Tclip

24 October 2004 - 01:01 PM

Alright, well yesterday I was working on a dart that would work in a tube clip, hadnt designed the tube clip yet, but I designed the dart...Lefty and BluearchNerfer put me up to it. Then I designed a clip, and wanted to test out my darts, so I built the clip, and its more reliable, cheaper, and easier to make then the rcsb barrel. It also has a bettr rof. The clip ended up working fine with regular darts, better even.

I call it the Tclip because it uses a T coupler as its base, and T stands for THIRST.

It rarely jams, and can hold many darts. It works better with brass, copper, and petg becaus the darts fit in there better than in cpvc. It can work in mildly powerful guns, 2k, blast bazooka, possibly mshot...

In these pictures I used cpvc, and brass. The brass worked better.
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image

THIRST

Clip Friendly Dart

23 October 2004 - 06:19 PM

Alright, southpaw(lefty) here put me up to the challene of making a tube clip friendly dart. After my first few designs failed, Arcanis did too. What a coincedence. I wuld take a picture, or make a diagram, but the computer with the nessaary programs is under reformatting-atation, so I cant do anything. Basically, I cut a 3/4" long peice of fbr, and in the middle of it(not at the ends) I made a small hole with a screwdriver, and lenght-widened it by sticing it in a bit more at an angle. I then put a bb in, pushed to to one side, another bb in, and pushed it to the opposite side. I added sme hot glue, and made it the ma eshape as the dart so it would work, and whalla. It can work in a 1/2 pvc tube clip, but gets a bit less difference. By about 10 feet. A small price t pay, since tube clips are used on already powerful guns. It doesnt need shells! if someone would plea emake a diagram sine I can, that would be great. Gawd I feel helpless withoulassotoshop!

[bb=-=bb]

[ is the ends, bb is the bb, = is the foam, - is the small hole which is sealed by hotglue. The ends are foam, not hotglue, to clear it up.

THIRST