nerfnrg

I have put together a list of McMaster-Carr parts number list because I know many of you do not know how to navigate through the search engine because it is very specific. If you have any part numbers that you believe to be useful in Nerf mods or homemades, PM me with the part number and what section you believe it to be useful in. Please do not clutter the thread. Thanks.

Zorn's video tutorial on how to use McMaster-Carr:


Function

+ Bow Parts:
2522A717 – General Purpose High-Speed Steel Hand Tap Plug, 6-32, H3 Pitch Diameter, 3 Flute
85805K28 – Polycarbonate Sheet 1/4" Thick, 12" X 12", Clear
85805K26 – Polycarbonate Sheet 1/8" Thick, 12" X 12", Clear
8538K18 – Black Nylon 6/6 Rod 1/2" Diameter (5 feet)
8585K43 – Polycarbonate Round Tube 1-1/2" OD, 1-3/8" ID, Clear
4880K314 – Std-Wall (Schedule 40) White PVC Pipe Fitting 1" X 1/2" Sz, Pipe End Male X Socket Fem, Hex Bushing
90131A104 – 1/2" Screw Size, 1-3/8" OD, 1/8" Thick Large-OD Extra-Thick Reinforced Rubber Washer
92510A700 – Aluminum Unthreaded Round Spacer 1/2" OD, 1/8" Length, #6 Screw Size
9637K26 – Continuous-Length Compression Spring Spring-Tempered Steel, 11" L, .844" OD, .08" Wire
9657K39 – Steel Compression Spring Music Wire, 1" L, 1/4" OD, .020" Wire Diameter
90309A154 – Zinc-Plated Brass Unthreaded Round Spacer 3/8" OD, 1/4" Length, #6 Screw Size
91780A125 – Aluminum Female Threaded Hex Standoff 1/4" Hex, 3/8" Length, 6-32 Screw Size
91780A131 – Aluminum Female Threaded Hex Standoff 1/4" Hex, 3/4" Length, 6-32 Screw Size
91780A337 – Aluminum Female Threaded Hex Standoff 1/4" Hex, 1-1/2" Length, 6-32 Screw Size
90402A144 – Zinc-Plated Steel Pan Head Phil Machine Screw External Washer, 6-32 Thread, 1/4" Length
90402A146 – Zinc-Plated Steel Pan Head Phil Machine Screw External Washer, 6-32 Thread, 3/8" Length
90295A075 – Nylon 6/6 Flat Washer #6 Screw Size, .140" ID, .313" OD, .057"-.067" Thk
98637A155 – MIL Spec Alloy Steel Cup Point Set Screw Cadmium Plated, 6-32 Thrd, 3/8" Length, MS51963-24
90631A007 – Grade 2 Hex Nylon-Insert Locknut Zinc-Plated Steel, 6-32 Screw Sz, 5/16" W, 11/64" H
90272A159 – Zinc-Pltd Stl Pan Head Phillips Machine Screw 6-32 Thread, 2" Length
90272A155 – Zinc-Pltd Stl Pan Head Phillips Machine Screw 6-32 Thread, 1-1/4" Length
90272A151 – Zinc-Pltd Stl Pan Head Phillips Machine Screw 6-32 Thread, 3/4" Length

Valves
7757K41 – Polypropylene Spring-Loaded Ball Check Valve Buna-N Seat, 1/8" Barb X 1/8" Barb (Same as 7757K11)
2987K21 - FDA-Compliant Nylon Check Valve for 1/8" Tube ID, 1-5/16" End-to-End
Length
6790T41 - Brass Push-button Valve, 10-32 Unf, Normally Closed, Projecting Style (Valve can be used for the 4K)

Barrels:
9245K25 – PETG [Same I/D and O/D as ½” CPVC(1/2" ID and 5/8" OD)]
8859K33 – Formable Brass (Alloy 260) Round Tube, ½” OD, 1’ Length
8859K34 – Formable Brass (Alloy 260) Round Tube, 17/32" OD, 1' Length
8859K35 – Formable Brass (Alloy 260) Round Tube, 9/16" OD, 1' Length
8859K36 – Formable Brass (Alloy 260) Round Tube, 19/32” OD, 1’ Length
8859K38 – Formable Brass (Alloy 260) Round Tube, 21/32” OD, 1’ Length
9056K673 – Multipurpose Aluminum (Alloy 6061) Tube 5/8" OD, .509" ID, .058" Wall Thickness, 1' Length (Same as 9056K67)

Air Guns/Air Gun Tubing:
5229K58 – Air-Gun Tubing. ¼” I/D and 3/8” O/D
5006K53 – Air-Gun Tubing. 1/8" ID 1/4" OD
38105K31 - Miniature Gauge - 5% Full-Scale Accuracy 29/32" Dial, 1/8" NPT Center Back, 0 - 60 PSI (Same as 38105K51)
5116K18 - FDA White Nylon Single-Barbed Tube Fitting, Coupling for 1/8” Tube ID
4379K51 - FDA Acetal Ball Valve 1/4" Tube OD

Adhesives:
7528A13 – PETG Adhesive. Also Works on Butyrate, Acrylic, Polycarb, and Polystyrene.
75215A511 – General Purpose Glue Stick, 1/4" X 4", 1-lb Pack (For Mini Hotglue Guns)
7518A711 – General Purpose Glue Stick, 1/2" X 4", 1-lb Pack (For Standard Hotglue Guns)
7518A714 – General Purpose Glue Stick, 1/2" X15", 1-lb Pack (For Standard Hotglue Guns)
7518A731 – HI Performance Glue Stick, 1/2" X 4", 1-lb Pack (For Standard Hotglue Guns)
7518A771 – Electric Hot-Melt Glue Gun High Performance Glue Sticks 1/2" X10", 1# Pack (For Standard Hotglue Guns)
7518A751 – HI Performance Glue Stick, 1/2" X 15", 1-lb Pack (For Standard Hotglue Guns)
7524A13 – Epoxy in Squeeze Tube Begins to Harden @ 20 min, 5-Ounce, Clear
1813A221 – Loctite® Hysol 1C Epoxy Adhesive, 4 oz Kit (Bonds metal, plastic, and wood. Temperature range is -65° to +300° F.)
1813A351 – Loctite® Hysol 608 Epoxy Adhesive, 2.8 oz Kit (Sets quickly; provides optical clarity. Bonds metal and plastic.)
74765A63 – Loctite® Prism Super Glue Surface-Insensitive, No. 401, .10 oz Tube, Clear (Surfaces require less surface preparation with these adhesives.)
74765A73 – Loctite® Prism Super Glue Impact Resistant, No. 411, .10 oz Tube, Clear (Provide strong bonds with higher impact and peeling resistance than other instant adhesives.)
75445A71 – 3M Scotch-Weld Super Glue #CA-4, 0.07-Ounce Tube

Replacement Plunger Rods:
8732K13 – Nylon 6/6 Square Bar 3/8" Size (For NF's)

Replacement Plunger Tubes:
8585K62 - Polycarbonate Round Tube 1-1/8" OD, 1" ID, Clear(For NF's)

Darts: (Note: McMaster FBR is known to be somewhat inconsistent.)
8771K1 – ½” Felt Stickers (CS Darts)
91083A009 – #8-32 Washers (CS Darts)
95495K121 – 1/2” Molded Domes (Bowler Darts)
77605T422 – 3/8” Foam Backer Rod
93295K43 - 1/2" Foam Backer Rod
77605T442 – 5/8” Foam Backer Rod
77605T462 – 7/8” Foam Backer Rod

Reinforcement Materials:
89015K37 – Multipurpose Aluminum (Alloy 6061) .063" Thick, 12" X 12"

Lubricants:
9463K32 – Barium Based, 4-Ounce Tube O-Ring Lubricant
1380K29 – Multipurpose White Lithium Grease 10.25-Ounce Net Weight Aerosol
1409K29 – Mold-Release Lubricant Silicone for Rubber, 10-oz Net Wt

O-rings and Rubber Washers:

Metal Washers:

Springs:
9637K26 - [k26] Springs or +bow/SNAP Spring
9637K25 – [k25] Springs
96565K36 – Useful Catch Springs
9637K19 - K19, nests over [k26]

Materials:

Acetal:
4379K51 - FDA Acetal Ball Valve 1/4" Tube OD

Acrylic:
85635K462 - Fluorescent Cast Acrylic Sheet .118" Thick, 12" X 12", Amber (Same as 85635K421)

Aluminum:
1658T49 - Architectural Aluminum Tube (Alloy 6063) 5/8" OD, .527" ID, 8' Length
89015K37 – Multipurpose Aluminum (Alloy 6061) .063" Thick, 12" X 12"

Brass:
8859K33 – Formable Brass (Alloy 260) Round Tube, ½” OD, 1’ Length
8859K34 – Formable Brass (Alloy 260) Round Tube, 17/32" OD, 1' Length
8859K35 – Formable Brass (Alloy 260) Round Tube, 9/16" OD, 1' Length
8859K36 – Formable Brass (Alloy 260) Round Tube, 19/32” OD, 1’ Length
8859K38 – Formable Brass (Alloy 260) Round Tube, 21/32” OD, 1’ Length
7757K41 – Polypropylene Spring-Loaded Ball Check Valve Buna-N Seat, 1/8" Barb X 1/8" Barb (Same as 7757K11)
6790T41 - Brass Push-button Valve, 10-32 Unf, Normally Closed, Projecting Style (Valve I used for the 4k)

Delrin(Type of Acetal):
8573K13 - Delrin Sheet 1/8" Thick x 12" x 12", White
8573K15 - Delrin Sheet 1/4" Thick x 12" x 12", White
8627K57 - White Delrin Tube 5/8" OD X 1/2" ID, 5' Length
8573K14 - White Delrin Sheet 3/16" Thick, 12" X 12"

Nylon:
8539K13 - Nylon 6/6 Sheet 1/8" Thick x 12" x 12", Off White
8539K15 - Nylon 6/6 Sheet 1/4" Thick x 12" x 12", Off White
2987K21 - FDA-Compliant Nylon Check Valve for 1/8" Tube ID, 1-5/16" End-to-End Length
8538K18 – Black Nylon 6/6 Rod 1/2" Diameter (5 feet)
90295A075 – Nylon 6/6 Flat Washer #6 Screw Size, .140" ID, .313" OD, .057"-.067"
Thk
5116K18 - FDA White Nylon Single-Barbed Tube Fitting, Coupling for 1/8” Tube ID


Polycarbonate:
85805K28 – Polycarbonate Sheet 1/4" Thick, 12" X 12", Clear
85805K26 – Polycarbonate Sheet 1/8" Thick, 12" X 12", Clear
8585K43 – Polycarbonate Round Tube 1-1/2" OD, 1-3/8" ID, Clear
87225K21 - Tinted Polycarbonate Sheet 1/8" Thick, 12" X 12" (slightly cheaper polycarbonate than clear stuff)
87225K61 - Tinted Polycarbonate Sheet 1/4" Thick, 12" X 12"

~Nrg

I was uploading a video for something so that I could send the link to others for them to view and when I tried uploading, it uploads, but then I can't see it anywhere in my albums. Please help. This is pretty urgent.

~Nrg

I am doing a mod for a friend that involves cutting a +bow spring. Does anyone know how to cut those spring? I tried wire cutters already but it barely made a cut mark. Thanks for your help.

~Nrg

I am modding my Titan to have multiple attachments but I am using the stock barrel attachment part thingy. I have searched but I have not found what size adapter to use for that. Thanks.

~Nrg

My friend and I were talking about Nerf guns and his airsoft Fa-mas the other day and when I told him that a fully modded Titan is way better than his Fa-mas and he wanted a video of a Titan's damage. Can someone make me a video of them shooting a regular stefan with hotglue tip or Slug style dart into sheet metal or polycarbonate or another plastic? Also please zoom in to the sheet after the shooting or walk to it and show the damage done. Thanks.

~Nrg

PS: If you guys think this is stupid, then admins, you can close or delete this thread.