5162 replies to this topic

[Boris99]

This is just a basic singled Titan, I call it "Her Majesty." All I did was plug the excess tubing and hot-glued a 1/2" CPVC coupler to the end of the barrel. It still shoots the missle but there is no dead space and darts will hit 250ft with a 15 inch speed-loader. However I have a 20 inch single barrel displayed, wich is more accurate but does not shoot as far.

Edited by Boris99, 25 March 2014 - 06:59 AM.

[stoicclown]

Some of my modded guns:

THE TITAN MONKEY WRENCH: Just the tool for most any job. Barrel has been modded to allow standard darts to be muzzle-loaded and fired straight from the barrel, while still allowing the big honkin' missile that the Titan came with to be loaded onto the barrel and fired.



Also has a scatter shot attachment that slides over the barrel for a 7-shot spread.





As well as a barrel extension for those handy-dandy long-distance shots.






THE OLD WEST COLLECTION: My pair of modded Mavericks, AKA my REV-6 Peacemakers. Standard air restrictor removals and Russian roulette mods. And the companion sidearm to the REV-6 Peacemakers... the REV-5 Peacemaker's Revenge (Sweet Revenge with a Western facelift, no internal mods.)




THE TACTICAL RAIDER: Raider modded to feel more like a tactical shotgun, with pump shotgun style fore grip/slide, extended muzzle, and Barrel Break tactical dart holder. Standard air restrictor removal and 5kg spring upgrade.




THE MIDNIGHT RECON: Barrel extension has been shortened for a stubbier look. Internals completely upgraded with an Orange Modworks steel Unleashed Kit.






And finally, my most recent project, my modded Sledgfire, which I have dubbed the SLEDGE-MARITAN. I wanted to remodel the feel of the Sledgefire to be more like a really big pistol instead of a shotgun. And since this would make a massive handgun with break-open action, I decided to use Hellboy's big friggin' revolver, the Samaritan...



... as my aesthetic inspiration.







So far no internal mods have been done, except for plugging up the air release holes on the plunger. But with a slugfire shell from Lasergnomes inserted into the barrel, it can blast out single elite darts with some pretty impressive power and ranges without the need to do alot of modding to the internals. Next I'm going to see if I can mod a slugfire shell to accommodate mega darts. A big hand cannon needs to fire equally big darts, if you ask me.

[TheNerfingFlamingo]

Working on a retaliator and switchshot now. posting pics later.

USER WAS WARNED FOR THIS POST

Edited by Zorns Lemma, 30 March 2014 - 10:37 PM.

[gehaga]

SalvoStrike: semi-auto big salvo tank hooked up to a magstrike bladder.

No official ranges yet.
Shot #: Result (without pumping between shots)
1: FRICKIN' LASERS
2: pew pew pew pew
3: wowie zowie
4: pew pew
5: 1.5x pew
6: (insert Colonel Prescott's famous Bunker Hill order here)

[Cyan Darts]

Buzzbee Double Shot I painted to look like a TF2 Soda Popper. haven't taken the air restrictors out yet, that'll come soon.




EDIT: Don't know why my pics aren't showing here..

Edited by Zorns Lemma, 30 March 2014 - 10:29 PM.

[RedFear]

Picture of my brass barreled longshot, no brass breech for this one due to lack of rigidity in brass for that application (14kg spring from blacktactical+OMW longshot upgrade spring. It has a reinforced composite bolt sled (xpower boltsled with aluminum reinforcement plates), an xpower bolt handle set, metal rail fitted, metal trigger, double catch springs, extended outer barrel, a paintjob (hyundai pearl mica black and Kyrlon pumpkin orange), all locks removed, airseal work done on the bolt, matching sling, and a red dot sight (scopes on nerf blasters are kinda pointless vs open-frame RDS sights.)

[Cyan Darts]

Picture of my brass barreled longshot, no brass breech for this one due to lack of rigidity in brass for that application (14kg spring from blacktactical+OMW longshot upgrade spring. It has a reinforced composite bolt sled (xpower boltsled with aluminum reinforcement plates), an xpower bolt handle set, metal rail fitted, metal trigger, double catch springs, extended outer barrel, a paintjob (hyundai pearl mica black and Kyrlon pumpkin orange), all locks removed, airseal work done on the bolt, matching sling, and a red dot sight (scopes on nerf blasters are kinda pointless vs open-frame RDS sights.)

That looks sick!

USER WAS WARNED FOR THIS POST

This thread is for pictures only

Edited by Zorns Lemma, 30 March 2014 - 10:30 PM.

[RedFear]

Some modification on my rayven project, codename Howler.
donor-blaster for extra motors and flywheels: stryfe.
uses 54t normal motor armatures inside high torque ball bearing motor casings for the front 2 motors and standard elite motors for the rear. 14.8 lithium polymer power for front motors, 7.2v lithium polymer power in rear.

Edited by RedFear, 31 March 2014 - 02:01 PM.

[tango down]

I'm still new to painting. I am inspired by many of the great projects here. This is a basic Maverick repaint with penny mod for an eight year old family friend. Nothing awesome, just trying to get a decent paint job. She liked it anyway.

[nine]

Finally modded something new:

It's a wrist mounted blaster that remains useable when using another blaster.



How it fits on the arm:



Close up of the trigger system:



And a video outlining the Effeminateness of the blaster:

http://www.youtube.com/watch?v=9nNaMchXvKQ

[dog green 1]

Another finished.

[KrazykilIa]

I'll start just by putting this up.
It's a modified nerf spactre.
Mods:
-added nerf longshot barrel Handel
-ARs removed in barrels
-paint job

I've left all the orange tips and buttons orange and there is a faint blue tone in some of the details in the paint job. The handle is epoxy puttied on to the spectre. Both the barrel and stock are removable.







This Gun is for sale if anyone would like to make an offer just shoot me a PM!

Edited by KrazykilIa, 27 April 2014 - 02:54 PM.

[Duke Wintermaul]

Full album

[archangel24]

Not too flattering pictures but will do a good photoshoot soon to show of the gun p0rnz...


New SM1500


Need to paint this Arrowstorm soon.


What was that about SuperSoakers being banned?

2K tank inside!!!

[RedFear]

The Howler Rayven, freshly painted in my normal paintscheme with its fresh aluminum plating (to protect/hold batterypacks) and 2-stage motor setup.
intermediate barrel: 19/32 brass
finishing barrel: standard nerf barrel
rear motors: elite stryfe motors run on 7.2v lithium polymer
front motors: AtomicRC High Efficiency vented ball bearing neodymium motor casings on 54t motor armatures run on 14.8v lithium polymer
Chrono reading: avg 128fps
paint colors used: Krylon oil-rubbed bronze and pumpkin orange

[Trajarian]

New here, figured I'd post some pics of what I'm working on.
My collection:

Maverick with straw mod and AR removal and reinforced Recon stock and minor mill-work. Stock bars will be wired-wrapped. Foam melee blades for the front are cheap and easy to replace. Absolutely a close range sidearm, with a range less than 10' no matter what I do to help it.




'Smooth-Cut 2x4' with extensive mill-work to remove tac-rail and body lines. Almost ready for paint.


Firestrike, before and after milling. Almost ready for paint.


Most everything else has basic mods like AR removals and seal improvements. Proton has safety locks removed and spring relocation.

[Trajarian]

Working into the wee hours of the morning to craft a stock for my Recon to replace the one I cannibalized for my Mav. Went ahead and cut down the shielding on the barrel extension too. Kept the bottom tac rail to use the flashlight as a slide to make it a pump-action.

[stoicclown]

Success! Following up on my previous post where I shared pics of my modded Sledgefire, or my "Sledge-maritan", I finally worked out a mod to allow the Sledge-maritan to fire the new Mega darts, but the mod is reversible, allowing me to switch back and forth to shooting either standard elites or megas from the same gun. I was able to accomplish this using the #2044t45 plastic tubing others have recommended, and a "slugfire" 3D printed shell made by Laser Gnomes. If you haven't gotten one of these for your Sledgfire, I highly recommend it (please consider that an unsolicited endorsement from a very satisfied customer). I simply bored out the hole in one of their slugfire shells with a 3/4" drill bit and nested in a 4.5" piece of the #2044t45 tubing.





This allows me to insert the new modded mega-slugfire shell instead of one of the standard orange tri-dart Sledgefire shells, then all I have to do is breech-load a Mega dart directly into the shell and barrel and fire it.





Of course, in order for the larger plastic tubing to fit in the barrel, I had to cut off the tips of the lower points of the clover-shaped cutout midway into the barrel and also remove the shell ejector lever.



This makes it possible for my Sledge-maritan to become my... SLEDGE-MARITAN MONKEY WRENCH.



Having no shell ejector trying to throw out my shells every time I break open the barrel to cock and load the gun is not a bad thing. With the shell ejector removed and the shells staying solidly in the barrel, I can now either insert a judiciously dremeled orange tri-dart shell and straight breech-load and fire 3 elite darts for that triple-dart shotgun blast, OR I can insert my unmodded slugfire shell and straight breech-load and fire a single elite dart with alot more range and power than the 3-dart blast gets, OR I can insert my Mega-modded slugfire shell and straight breech-load and fire a larger caliber Mega dart (which is more satisfying coming from a mondo-sized pistol).



I'm a very happy camper.

[Gunyboy007]

This is my first primary integration mod.
I introduce to you, "Sweet Justice".


The Rampage has the AR removed, added a slightly stronger spring, and i re-lubed all the internals.
The triad has the vacuum holes on the bottom and the prongs taken out the chambers.


The stock is comprised of the main part of the stockade stock and the back butt of the praxis stock.
It is now the perfect length for me plus it now is super comfortable and super sturdy.

Edited by Gunyboy007, 12 April 2014 - 01:11 AM.

[Draconis]

I don't post in here all the time, but when I do, I reach for Dos Blasteros!



Nothing special, Spy Gear Rocket Launcher with a hopper and pump replacement. The only really helpful things I found are:
1) The tanks are a round profile, lacking the flat spot that the 4B version uses, so with a little widening of the hole in the shell for the top intra-tank support, you can rotate the assembly 120 degrees and have hose inlet point downish to the right or left.
2) The tank inlet can be tapped to accept 1/8" NPT fittings, which is quite handy.



Again, nothing special here, just a Marshmallow Crossbow with a hopper. After testing with just the bow arms installed, I was still only getting 60-ish feet with Slugs. That just isn't acceptable, so I added a length of green Theraband as well. Now it is hitting century-mark children all day.

If anyone else is interested in using Thera band, this chart is helpful for determining what kind of strength you get from it. Also, I have tons, because I keep finding it at Goodwill.

Edited by Draconis, 30 April 2014 - 08:12 PM.

[stoicclown]

Not sure if anybody has specifically done this yet, but I can't recall seeing anything so here it is. Easy mod converting a standard 6-shot quick clip into an 8-shot clip. The hardest part was getting my clip to open up. Once I did that, I took out the dart slide and cut it in half (from about 1" deep to about 1/2" deep) which easily makes enough room for 2 extra darts. Also enlarged and extended the view slit on the one side of the clip and cut another to match on the other side to improve the view of how many darts are in the clip. Just thought I'd share.

[Majestic]

My Air Max 10's











The first version has two tank expansions and a single action pump. The second has a single expansion and a dual action pump.
Both have all mods covered in the write-up.

[bum]

Another Bandit style Borderlands gun. I call it Irwin

Edited by bum, 20 April 2014 - 01:44 PM.

[Xenomorph1320-D]

Plasmacaster Stampede!:

Inline Longshot:

[232524z]

Here is my Nerf long shot with a semi custom paint job. Pictures first, details after.

Upgraded 5k OMW spring
All locks removed
Base coat of black with white stripes

Edited by 232524z, 22 April 2014 - 03:13 PM.