Modification and Paintjob Pictures
Posted 23 May 2013 - 09:15 PM
All locks removed , volt meter installed on back end cap, D.I.Y. GLOW IN THE DARK add on, 9 volt conversion.
Posted 24 May 2013 - 08:56 PM
So far, I have only taken her up to 50 psi. It takes about 12 seconds to get there and I can fire off about 6 good shoots.
I don't care (if you ate sceptors and air compressor powered blasters... especially combined) I love it.
PA POWER Clan Is that all ya got?
Posted 25 May 2013 - 10:53 PM
I modified this Lanard First Shot quite a long time ago.
As you can see in the above photos, a shorter shutter speed gives more clarity in details such as writing on the blaster and shadows made by it. A longer shutter speed (Up to a certain point, that is. After that it just start becoming progressively more washed out.) makes truer colors on the blaster, but lacks a slight amount of detail in shadows and writing. Unfortunately, Photobucket robbed my pictures of some of their clarity, so you can't really see the shadows anymore. It is a shame that almost, if not all photo hosting sites compress your photos. They basically cut out light and detail to minimize the photo's size.
I really like this type of photography: it gives better focus, and there is no glare on the subject from the flash.
Edited by DartSlinger, 25 May 2013 - 11:04 PM.
Posted 26 May 2013 - 12:04 AM
It uses the boltsled and the original priming handle to push the barrel assembly backwards.
The return spring is inside the blaster and the boltsled is bolted through the wye and the cpvc.
Hopefully it holds.
Comments/questions are always nice in a PM
Posted 26 May 2013 - 12:13 PM
CPVC barreled, party popper spring + stock spring, AR removed, seal improvements. I tried to keep it as stock looking as humanly possible. I was expecting the usual maybe 60 feet, but this one surprised me..... it's got to be getting at least 75 feet. It left welts on me at close range from Elite darts.
Posted 28 May 2013 - 11:48 PM
Writeup here: http://www.nerfrevol....php?f=8&t=6000
(Selling it if you're in the mid-west, 9 pounds is not fun to ship)
Made purity seals for it:
Also made a small shield to use too!
Edited by hummer, 29 May 2013 - 10:16 PM.
Onto the anvil of war!
He parkours over flat land while yelling tactical orders at no one. Demon Lord is the most legit ballsy nerfer of all time.
Posted 29 May 2013 - 06:01 AM
I based this splat on Blitz's here http://nerfhaven.com/forums/index.php?showtopic=5250&st=3765
MIne has a few changes. Mine is using 1 1/4 in thinwall pvc for the plunger, everything is also mechanically fastened, and it houses a k45+K31 combo up in the front. This ridiculous spring power, coupled with the already diddle spring in the blaster, allows it to hit upwards of 95 feet.
Edited by Birch, 29 May 2013 - 05:55 PM.
It's like a Hurricane ate a Tornado and shat out a Monsoon!!
Posted 29 May 2013 - 04:54 PM
Whilst hunting zombies at night during https://www.facebook.../DarkTempusLarp, I discovered a slight problem with my retaliator, in that to use my torch I either had to lose my vertical grip or lose my sight. So I went all COD on it and fixed it.
QUAD RAILS BABY!
Edited by BritNerfMogul, 29 May 2013 - 04:59 PM.
Posted 30 May 2013 - 05:50 PM
Long live Crossbows.
I'm about 5 years late to this party... YOLO!
Mods Done: Level 5 (You've probably never heard of it before).
Integrations: +Bow, Mad Swagger, Dildo.
Ranges: Farther than your Crossbow.
Comments: After neglecting my Crossbow for close to two years, I finally decided to modify it for war use. The archived modifications for Crossbows are largely subpar for actual war use. I looked to Coop's recent Crossbows and started from scratch with similar techniques.
A common problem with replacing the plunger tube on a Crossbow is that a +Bow sized plunger tube (1.5" OD) is slightly too large for the shell, leaving a 1/8-1/4" gap. This has lead to smaller plunger tube replacements to avoid this gap, with losses in range and hopperability.
Fuck that, I went with the +Bow plunger tube. With adequate additional screws this gap can be closed across the shell quite easily.
Securing the plunger tube into the shell was accomplished by two screws in the rear spring rest of the plunger tube. This bypasses the need for a screw through the front bushing, and by proxy the need for a plunger tube housed entirely within the shell. This allowed me to achieve a greater length of draw with a +Bow length of plunger tube (11 and 1/2 inches); A tad over 6 inches of draw.
Before I started this project I debated the practicality of modifying a Crossbow in this day and age of the NIC community. I doubted whether or not it would fill a useful niche along with my +Bow or pump-action dick guns.
It does. It shoots as far if not farther than my +Bow, is mad comfortable, compact, and obviously swagnificent. If anybody ever tries to tell you that Crossbows are overrated, they're wrong. So very, very wrong.
Edited by Xellah, 30 May 2013 - 06:16 PM.
it cant be as bad as reloading an ak-47 on the run
Posted 31 May 2013 - 10:48 PM
Posted 04 June 2013 - 06:03 PM
Posted 04 June 2013 - 06:12 PM
Drop clip Strongarm
Singled Big Blast
On the other hand, the guy who posted before me used the word 'fuck' a lot so he probably knows what he's talking about.
Posted 05 June 2013 - 12:33 AM
Slytherin style Maverick
Loving these things
Got just over 9 coils of [k26] in each, not about to let them break....
Edited by archangel24, 05 June 2013 - 12:42 AM.
I would much perfer a game that's free of KY. I like it rough. Right, Vacc?
"She went all Ghetto Fab on you."
Posted 05 June 2013 - 08:28 PM
Posted 06 June 2013 - 09:15 AM
Edited by BrianSTR, 06 June 2013 - 09:15 AM.
Posted 06 June 2013 - 11:24 AM
Recon pump action mod.......works quite nicely & goes through the 18 dart clip in bout 15 seconds.
Edited by MightyAP, 06 June 2013 - 11:33 AM.
Posted 07 June 2013 - 07:46 AM
The pair after.
Customer wasn't thrilled about the blue so it got changed to black
after that first one this my second creation The scope didn't survive, the weight threw off the slide action.
I did the AR removal MOD and the extended swing out mod
Thanks for viewing
Posted 07 June 2013 - 08:05 AM
A Halo 4 railgun-inspired Rayven:
Edited by Tigadee, 07 June 2013 - 08:09 AM.
Posted 08 June 2013 - 12:33 AM
1 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users