5162 replies to this topic

[firesflame4]

This is one of the two Lanard Shotguns I'm taking to Apoc.



It will be getting a paint job tomorrow. The homemade pvc wye is basically a placeholder until my shipment from flexpvc.com comes in.

[NerfRogue83]

My MegaMissleStorm revised a bit.......

I swung the pump to the opposite side---way more comfortable, improved the turret seal, and replaced the 3k pump with a BasketBall pump.






A Contract LS for A New Rage.......PETG+17/32 breech, powerfull springs, pvc'd stock, mega-reinforced Boltsled, beefy catch, superb plunger seal, ultra deadspace removel. 90's easy.

[firesflame4]

Here is the paint job.

The white paint I had wasn't very good so that looks like crap, but it's better than being stock colours.

[baghead]

Thanks for posting my pictures of your guns Lucian.

Here's a couple commissioned paintjobs on Crossbows for Nerfer9 and HOTH

N9's Bow: "Hostage"











^ worth noting, metallic camo doesn't work as well with Red/Yellow there is an "orange" but its only noticeable in person and in direct sunlight

HOTH's Bow: "Stockholm Syndrome"







This would be the one he made This Thread about... Cleaned up the shell, gave it a classy metallic black (with textured glitter metallic) and royal blue traditional Crossbow scheme.

-Bags

PS: Yes, the names are jokes due to circumstances I won't go into.

Edited by baghead, 31 July 2010 - 10:19 PM.

[cheyner]

That is amazing work Baghead, I really need to start painting.
At least this has some nice faded character to it. I found it at a garbage dump in perfect working order.
I give you Second Chance, my rescued SuperMaxx 1500



Butchered rear loading slot:


Craft foam for the turret seal.
Plugged pump.
Cleaned so many times I lost count.

[trogdor65]

Just something I was working on this weekend to keep me busy, I really like how it turned out. (Although the pictures do portray the green in an odd shade.)

It was originally an airsoft gun given to me by a friend, I believe it is modeled after a G36C or something along those lines. I gutted the original internals and replaced them with two big salvo air tanks and pump as well as a hornet blast button. Both barrels fire simultaneously with one pull of the trigger. The barrels are composed of SCH 40 1/2" PVC pipe with short sections of 9/16" brass pipe nested inside.

This gun has a folding stock, tactical rails (for a flashlight mostly), and the sights on top are not extremely useful but semi-cool/fun to have and use.

Overall really like how this gun turned out and had a lot of fun making it.

Enjoy!

[hawkshot]

First documented modified CLEAR deploy on NH and NR(I don't check nhq);

Hoppered LS, shoots very well:

[louiec3]

Venom and I overhauled a 3k.

It's super 1337.




Tacticool gauge

Giant rearloading slot.




We ran out of petg so we used aluminum.

[Zack the Mack]

Super Soaker Iron Man + 3K + bike pump + 5-dart breeched hopper + 14" brass barrel + 7" breeched barrel + N-Strike Rail + Pinpoint Sight = My Apoc primary.



Super Soak that ho.



The red dot sight isn't just for tacticool overkill - because of the air tank's orientation, it's impossible to aim down the barrel. The blaster's accurate enough for the optics to work.

[westpyroairsoftboy]

Zack, 'm SOOOOOOOOOOOOOOOOO fucking jealious. Nice Work. Here's some of my latest:

Pistol Splat w/Shit PJ:


Compromiser V1.0:


Old Original Painted NF:

[ZimZam93]

thats is my baby, my first modded gun, AR removal, double springed, and red tiger for kicks



This is my longstrike, i dont use it for wars, cuz the rages are awful, but i like the paintjob and extras i put on for looks





this is my raider, its one of my favorites, good ranges, and cool paint job
sorry about picture quality, using my webcam is much easier then my real camera

[louiec3]

Its a pulsator with extended mags. Snake wanted more balls for his.

I would post a link to the write-up, but I'll just save VACC some time.

http://nerfhaven.com...p?showuser=1034

[NerfRogue83]

Lou-- no Nrev links, LULZ.

Anywho, thanks for the upgrade Jake.

[firesflame4]

This in my AT3K integrated into an Alpha Trooper.

I left the original air tube because I like the way it looks.

Here is the breech.

The air tank location.

I would be taking this to Apoc, but I need to work out a trigger problem and I don't know if I will have time to do that with me finishing my Hopper clips which the Wyes for them come in the mail tomorrow.

Edited by firesflame4, 04 August 2010 - 09:40 PM.

[sci-olyrocks]

I just picked up an Alpha Trooper this morning. It preforms great for a stock gun(~30 ft.), but I thought I would make it better buy preforming some basic mods.




First of all, I removed the AR by drilling it out. It took me a while because there was some new piece inside the tube that I have not seen in other clip system reverse plunger guns. (That piece is not pictured)


I then covered up the little hole in the tube with a little piece of duct tape.


And finally I put duct tape around the plunger tube for better spring compression.


I also made made it possible to move the jam door at any time. It is the same as on the longstrike.
It now gets 40+feet, and I've seen it get 60, but that is because streamlines are crazy darts.

Edited by sci-olyrocks, 06 August 2010 - 08:30 PM.

[taerKitty]

Got more work done on my Cluster-Eff of a 4B:

Unsure if this is anything new / newsworthy, but what SublimeDom77 on IRC dubbed the SpeedHopper.

Topmost dart sometimes falls out of it. It also falls when I point the blaster above 45-degrees, but when would that happen?

===

MuttonChops' Chopper, lowest profile I can manage. I used 1" thinwall PVC on the outside to join it. It's tight enough to solvent weld holds it to the wye. More solvent weld to attach the elbow to the wye. I needed to wrap the 45-degree elbow in some e-tape to get it seat properly. That's not airtight, and I don't trust the solvent weld itself, so there's a ring of hot glue top and bottom.

Biggest win: bigger throat leading to the wye into which for the dart to fall. I prime it by moving the blaster back and forth - that's enough to jostle the dart into the wye, but I did have one misfeed. Maybe I had the blaster tilted slightly back when I was pumping it.

Ball valve on the back to load, with a ring of 1-1/4", with a 120-degree chunk cut out, to stabilize it. The wye + Chopper come off the blaster as one piece. The three-quarter 1-1/4" ring stays on the blaster. I guess it works as a sight. I just added it, so I'll have to see come next war.

===

Close-up of the connection. (Also, a ring of CPVC dart holders. Nothing special about that; I just wanted to explain the purple stuff (primer) in case anyone was wondering.)

===

There's a nub of PVC on the blaster that stays. The barrel detaches, so each wye is pretty much dedicated to its own magazine system.

[Ice Nine]

We had a neutered NIB war yesterday.



I made a Berserker.



Many crayolas and barrel pegs died to bring this gun to usability.



ZOMG WE'RE AT APOC.



Tacticool.

[zer0metal]

My RSCB'd Nite Finder.





I can use the barrel either by itself or on the Rscb.




I removed the original pcb with the light on it and cut the tube down so i could fit the lazer in.




I still have some work to do, remove some deadspace, pad the plunger head and some bodywork and a paint job.

[NerfRogue83]

Super BoltSled!...lol

Well, I felt I should share a few pics from after this weekends war. When not properly reinforced with insanely strong springs added ,the Boltsled breaks. My sleds+ internals are ALWAYS up to the task......too bad the METAL priming bar was not---LOL

[archangel24]

Finally got my quad-shot back from Shrub.
I gave it a worn-snow-camo PJ


Right Side View


Left Side View


The turret that was in BadWrench's writeup (given to me by shrub)


Plunger Draw Extension (done by shrub)



Sloppy Rear-Loading Slots (done by me)


9" turret that i did rushing without proper tools at a friends house the night before a war:



Barrel Spacer:

[Soccerman]

I've been lurking around this forum for at least two years now, and thought it was about time I gave back to the community which has helped me numerous times.



My Scout with a black and gold paint job.

[archangel24]

A WIP that I have been working on for over a month now and I just recently installed it into a mav.

I call it the VMT.
Volley-Mav-Titan:

[meierboy97]

singled ls w/ integrated singled hyperfire (both had broken parts) made entirely out of 1/2 pvc for barrel which is all i had or else i woulda used 1/2 cpvc... hyperfire has a basic string onto key ring trigger... btw this is my first post.picpicpicpic

[archangel24]

Lastnight I was unhappy with the performance of my Quad-Shot and decided to do more stuff.

Catch Reinforcement:



Draw Extension:


Now goes far enough back for the 8th catch but slips gets around 100' flat with streamlines.
Working on getting it to go to the 9th catch. Has a stock spring and blue ls spring.

Stock Addition WIP!

Edited by archangel24, 11 August 2010 - 02:35 PM.

[BritNerfMogul]

Will be receiving a PJ when my paint arrives