Helio

[img]http://lh5.ggpht.com/_iB45nYl6EXY/TCj_1E-IoWI/AAAAAAAAAA8/bNGE-h8KMIQ/s640/SSPX0756.jpg[/img

Every single one of your end tags is broken the same way.
That's really not very helpful. Inside a set of CODE tags there's no reason to leave anything half-done.

I did that because it won't let you post it with the tags closed. it says:
You are not allowed to use that image extension on this board. A valid format is: http://www.domain.com/picture.gif, an invalid format is: http://www.domain.com/picture.one.gif

Today we are going to make this:

[img]http://lh5.ggpht.com/_iB45nYl6EXY/TCj_1E-IoWI/AAAAAAAAAA8/bNGE-h8KMIQ/s640/SSPX0756.jpg[/img

You need what's in this picture:

[img]http://lh5.ggpht.com/_iB45nYl6EXY/TCj__AEYhvI/AAAAAAAAABc/3Alr_SB6A8E/s640/SSPX0766.jpg[/img

[b]Supplies:[/b]
DUAL ACTION AIR PUMP
tape
scissors
2 lengths of 1/2 in. PVC (connected with a ball valve)
rubber bands

First, wrap tape around the air outlet thing
[img]http://lh5.ggpht.com/_iB45nYl6EXY/TCkABIpvxzI/AAAAAAAAABg/ZodpjOjqALg/s640/SSPX0767.jpg[/img

second, cut the two ends of the pipe about an inch from the ends:
[img]http://lh4.ggpht.com/_iB45nYl6EXY/TCkAB1EfIOI/AAAAAAAAABk/bl8vfx1GT2A/s640/SSPX0768.jpg[/img

third,put the "quick release" side of the cut pipe on the outlet you marked with tape:
[img]http://lh6.ggpht.com/_iB45nYl6EXY/TCkACu7KlQI/AAAAAAAAAB0/3qJtatj-k4E/s640/SSPX0769.jpg[/img

Put the short end of the PVC into that:
[img]http://lh6.ggpht.com/_iB45nYl6EXY/TCkAD68hQGI/AAAAAAAAAB4/JOK3TnEyDZU/s640/SSPX0770.jpg[/img

Fourth, use the rubber bands to keep that in place:
[img]http://lh4.ggpht.com/_iB45nYl6EXY/TCkAFlposkI/AAAAAAAAACA/vlni13xPZss/s640/SSPX0772.jpg[/img

Fifth, cut the "sports" fitting off the end of the pipe:
[img]http://lh6.ggpht.com/_iB45nYl6EXY/TCkAHj9mcRI/AAAAAAAAACI/ogHtrvJ-kNk/s640/SSPX0774.jpg[/img

put that into the remaining end of the pipe:
[img]http://lh3.ggpht.com/_iB45nYl6EXY/TCkAIibHkWI/AAAAAAAAACM/0mNy2n-IU0s/s640/SSPX0775.jpg[/img

And you're done!

Oh, and remember this?:
[img]http://lh3.ggpht.com/_iB45nYl6EXY/TCkAIibHkWI/AAAAAAAAACM/0mNy2n-IU0s/s640/SSPX0775.jpg[/img
put that onto the end of the PVC to make it into a water gun!
(in "water gun form" try tightening and loosening the ball vavle to make the stream go further(Insert your own joke here))

(P.S. my darts all got torn up due to my friend's dog so I can't get ranges at the moment.)

Code for you.
Use [img] URL of IMAGE /img] tags for images. Just edit you're post to what I edited for you and see what feedback comes.

You are not allowed to use that image extension on this board. A valid format is: http://www.domain.com/picture.gif, an invalid format is: http://www.domain.com/picture.one.gif

What is that? and end the brackets ] so the links work...
Spent wayyy too much time on that.

Ok, now I see what you're doing.

Its not acrylic, but .030 Petg sheeting. I am very much aware that I need to get the corners sharper, do you think setting the toaster to 500 degrees and using a shop-vacc would solve the problem?

And I think that might be too hot for the SS2, but (I think) it would solve it if it didn't melt the SS2.

That is extremely neat, but how do you plan on getting the plastic back to the shape of the SS2, since right now it is slightly larger?