Jump to content


man with many guns

Member Since 11 Oct 2005
Offline Last Active Mar 01 2006 11:10 AM

Topics I've Started

Supermaxx 750 Mod

05 December 2005 - 07:22 PM

All right, so you all know the story with this gun, lets get down to moding it. Hereís the gun stock: Posted Image
Tools needed:
6in. of Ĺ inch cpvc
Phillips screwdriver
Hot glue gun
Hammer
Something to pry/smash the orange caps off

1. Surprisingly, the hardest step. Do what ever you can to get the orange caps off (dremel, file, smash, pry, melt, just whatever you can). Then remove all the screws.
Posted Image
2. Take the pump out, and plug it with your hot glue gun. It should look like this (sorry the pic is low quality): Posted Image
3. Cut the your cpvc with a hack saw, then file the ends. Posted Image
4. Take the cpvc and pound it down in the valve, and place a ring of hot glue around the cpvc, and it should look something like this: Posted Image
5. Place all the internals back in the case.
Posted Image
6. Screw the case back together. Now you have a foamy weapon of doom!
Posted Image

At2k Quad Mod

02 December 2005 - 08:03 PM

AT2K Quaded
The at2k, a great gun once modded, before, not so much. Some of the time the darts donít even leave the barrel. So lets mod this bad boy. Hereís a pic of it un-modded :
Posted Image
Supplies needed
4x6-8 in. of Cpvc
Screwdriver
Hacksaw
File
Hot glue gun
A hand
A working brain ( I know some of you donít have this ;))

1.Remove all screws. It should look like this:
Posted Image

2. Remove the pump from the pump tube and plug it with your hot glue gun. Once your done, place it back in.
Posted Image

3.Remove the turret from the case.
Posted Image

Make sure you keep this piece right here right here, the o-ring:
Posted Image

4. Cut off the end of the barrels with your hacksaw about ľ or1/8 in. from base type thing. You should see springs and junk, keep on going, and in the middle you should hit a medal post, you want to swerve around that, because it would be a lot more work that is necessary to but through it. This is what it should look like:
Posted Image

5.Cut 4 6-8 inch segments, but make them all the same length, as if you donít make them the same length you will get varied ranges.
Posted Image

6.Take your turret, and hot glue your cpvc barrels. The best way to do this is to do it 1 at a time, and glue the turret and the barrels, then stick it on, and then glue around it.
Posted Image

7. Place the o-ring back in the turret back, and place the turret on the valve. It should fit back together perfect.
Posted Image

8. Screw it altogether.

9. ~Enjoy

Knives/swords Collections

26 November 2005 - 04:03 PM

There was a gun topic, so I thought what the heck, why not. Post pictures of your knives/swords here. I'll post my collection: Posted Image
Feel free to post 1 at a time or all at one.

Nf Mod

13 November 2005 - 12:09 AM

A not so good gun stock e-x3, and doesnít use itís full potential. Thatís about to change
Posted Image

1.Remove all screws. There should be 14. Open the gun carfully.
Posted Image

Optional step: 2. remove led light
Posted Image

3. Un-screw the plunger, and throw away the pieces but these:
Posted Image

4. Take the air restrictors, and punch them out, by any means. They should look like this:
Posted Image

5.Place now non-restricting air restrictors on plunger tube.
Posted Image

6. Cut 3Ē inch length of cpvc
Posted Image

7. Hot glue cpvc on plunger tube.
Posted Image

8. Trim case to fit the cpvc.
Posted Image

9.Place all internals in case
Posted Image

Double Shot Mod

11 November 2005 - 10:31 PM

An alright gun stock.
Posted Image

Our main mod is going to be on the shell not the gun
Posted Image
Tools needed
Hacksaw
Needle nose pliers
Cpvc
1. Take your pliers and remove the middle posts
Posted Image
2. Cut off the end of shell
Posted Image


3. File off end
4. Cut a 2" piece of cpvc
Posted Image
5. Place cpvc in shell, with some e-tap on the end or for a more permient effect put hot glue on the seem
Posted Image
6. Enjoy!


Ranges: About 5- 10 more feet than stock