Find content
This is a snowboard video me and my friends made
click right here
Im the one in green pants
oh, and if you got a snowboard video post it up
forgot to ask if anyone has the spinning thing down. I can 10 and 360 but im still working on getting a 540
nat
Member Since 27 Jan 2008Offline Last Active Dec 26 2011 11:23 PM
Topics I've Started
New Hornet Mod
03 January 2009 - 11:48 AM
Well, after seeing CaptainSlug's MASS project it inspired me to create this.
materials:
Hortnet
Dremel sanding wheel
Vacuum
6 pvc endcaps
9" of pvc
Jb weld two part epoxy
Ok here we go
1 Open up your hornet and take a good look at the intimidating internals.
2 take a sanding wheel and move it in a up and down motion on every blast chamber until theres a 3/4" hole in them.
3 now cut 6 1.5 inch segments of pvc.
4 smother one end of it in pvc cement and slap a cap on eveyone of them.
5 once your done with that take your sanding wheel and round the end of your pvc segments to match the curve of the blast chambers.
6 Now take your epoxy and litely dip the rounded end of pvc into the epoxy and stick it on a last chamber
7 Do step 6 to all the cambers and cut the shell so theres room for the extensions and your done.
you get props if you dont get frustrated during this mod
finished product
Edit- thanks imaseoulman for helping me understand how blast chambers work
materials:
Hortnet
Dremel sanding wheel
Vacuum
6 pvc endcaps
9" of pvc
Jb weld two part epoxy
Ok here we go
1 Open up your hornet and take a good look at the intimidating internals.
2 take a sanding wheel and move it in a up and down motion on every blast chamber until theres a 3/4" hole in them.
3 now cut 6 1.5 inch segments of pvc.
4 smother one end of it in pvc cement and slap a cap on eveyone of them.
5 once your done with that take your sanding wheel and round the end of your pvc segments to match the curve of the blast chambers.
6 Now take your epoxy and litely dip the rounded end of pvc into the epoxy and stick it on a last chamber
7 Do step 6 to all the cambers and cut the shell so theres room for the extensions and your done.
you get props if you dont get frustrated during this mod
finished product
Edit- thanks imaseoulman for helping me understand how blast chambers work
Pump Action Shotgun Cpvc Mod
01 September 2008 - 06:35 PM
Om' I wanted to do a mod on my Ertl shotgun like angel, But my parents wouldn't let me buy some brass. So I give You this.
step 1: Cut off the Ball shooting thing.
Step2: Sand out the Inside Of the orange part out until a PVC coupler fits In It.
Step 3: Epoxy that coupler In the orange part. Get It as strait as possible.(Sorry no picture)
Step 4: Cut one side of a cpvc coupler up to the ridge in the middle.
Step 5: Put a cpvc pipe through this brown piece. Put a coupler on the end pull It against the brown piece and put hot glue aroung It.
Step 6: get a 1' piece of cpvc put E-tape around an Inch or so away from one end and put somemore on the other end and slide some Thinwall pvc over It.
And your done!
Finished product.
A Look down the front.
step 1: Cut off the Ball shooting thing.
Step2: Sand out the Inside Of the orange part out until a PVC coupler fits In It.
Step 3: Epoxy that coupler In the orange part. Get It as strait as possible.(Sorry no picture)
Step 4: Cut one side of a cpvc coupler up to the ridge in the middle.
Step 5: Put a cpvc pipe through this brown piece. Put a coupler on the end pull It against the brown piece and put hot glue aroung It.
Step 6: get a 1' piece of cpvc put E-tape around an Inch or so away from one end and put somemore on the other end and slide some Thinwall pvc over It.
And your done!
Finished product.
A Look down the front.
