Javascript Disabled Detected

You currently have javascript disabled. Several functions may not work. Please re-enable javascript to access full functionality.

KainZero0133's Photo

KainZero0133

Member Since 16 Jan 2012
Offline Last Active Jan 08 2013 12:00 PM

Find content

About Me

Good day all, well for starters I'm 23, in college for Architectural drafting/design, and after ill go back for 3D graphics design...with that said I'm also a professional magician. As far as Nerf goes I have a decent arsenal I'm rather happy with, most of which having been modded in some way, mostly ar removal and repainting. I guess this is the fun part where I tell you about them a bit.

I'll go on and list them in the order I purchased them:
-- Maveric -- mostly dark green repaint, barrel extension, ar removal, spring stretch.
-- Buzz Bee's "Ultimate rapid Blast" -- No mods
-- Nerf Vulcan -- Complete repaint.
-- Buzz Bee's "Ultimate missile Blast" -- slimmed the frame down, need to reseal it to fire correctly though.
-- Nerf Recon -- repaint of stock and barrel attachment, no mods to main gun yet.
-- Nerf Titan -- unity attachment clips, spare trigger and ball bearings removed. plan to do vent removal
-- Nerf Scout -- repaint, attached nitefinders light withought light (cosplay prop) and white/grey repaint. Also ar removal
-- Nerf Hornet -- didnt work no matter what i did...scrapped for parts.
-- Longstrike -- repaint only -- black + khaki for star wars cosplay (went with nitefinder for tusken raider costume)
-- Longshot -- repaint only -- black + green. no repaint on front gun yet.
-- Nitefinfer -- Ar removal + white/khaki repaint for star wars costume
-- buzz bee Double shot -- now sawed-off. repainted with black and silver, and ar removals to gun and shells.
-- Nerf Raider -- black + dark khaki repaint. stock too.
-- Nerf Barricade -- grip left alone as far as repaint went. liked the color. the rest was a worn metal + dark red. trigger, on/off switch, barrel, jam door and very end of barrel (wider segment with holes in it on end of barrel) are left orange.
-- Star Wars Captain Rex Electronic Blaster -- just bought, working on planning for cutting the stock off, salvaging electronics in one group to be reused maybe. I'll be using this gun as an under barrel attachment using the recon scope mount.
-- Buzz Bee Hawk -- stock removal (yes i know, the not-so-hidden compartment gets removed.) and assessment of internals for possible modding and finished with a good painting...also need to see about making it not use shells...i like it but i dont but i do...figure that one out

for my current work I've been using OMW's forums. this is a link to the under barrel work, the second link is my already painted projects:
http://orangemodwork...1326859816/0#12
http://orangemodwork...?num=1314052181

Community Stats

Group Members
Active Posts 16
Profile Views 4,518
Member Title Member
Age 36 years old
Birthday July 29, 1988

Posts I've Made

In Topic: New Member from Florida saying Hi

04 February 2012 - 11:46 PM

All good, I honestly had no clue where to put that stuff, but on a compleatly non-nerf topic I wanted to share my acrylic cane project. Took a good 45 min to heat the 1" wide rod at the end o where I could bend it correctly. I applied the "sit on long end, wear gloves, wrap a towel around hot end and pull up and until a nice curve is achieved" method. That took a few min plus or minus time for reheating it to make corrections. After that it had to be held in place. Today I took the (already spray painted) pvc pipe section I had and fit it onto the handle after cutting the handle down and some of the bottom to get it to the right height. Put the pvc on with a 2 part epoxy, once it set a bit I took super glue and an inch of celcro (the furry part only) and fit it to the indide of the pipe (furry sode facing inward). Strange as it may sound, it was than used o fit my flashlight to the pvc. The velcro allowed a tight fit and with. Bit of twisting it can be safely removed. Oh, and the light has 2 buttons, red for the red light, and black for the white light.

Posted Image

In Topic: First Homemade project.

04 February 2012 - 11:34 PM

Well I found a nice bike pump with a pressure gauge. Working on making it fit/connect.

Posted Image

Also, I used some electric tape to make a pipe fit into a larger pipe so I coul make a barrel attachment. The wide end is the end of the barrel.

Posted Image

In Topic: First Homemade project.

03 February 2012 - 12:03 AM

Well, i didnt notice that before...its in a ziplock with some of the other parts from that gun...i kept most of it i think.

In Topic: First Homemade project.

02 February 2012 - 11:19 AM

Well I suppose I could do that, have it latched to the gun, use it as a stock and than use its hose that normal bike pumps use and attach it to the hole on the guns front so I dont have to make any unneeded cuts/holes. Ill consider this idea too vs the double action pump, if I got that it'd be mounted to the front of the gun under the barrel and probly epoxied ot something to it with possibly a tube between them if theres not enough space. I like the stock and pump idea, but (go figure) I like the foreward pump action/grip.

In Topic: First Homemade project.

02 February 2012 - 12:39 AM

I was thinking the same, especially since its a good price. Now to see where I want it, depending on its size in person it may make a difference on how I mount it...I did also consider a homemade one but at this price and I can get it by fri/sat. I may just get the dual action one. As it goes, I felt it was better to ask first, and besides, if it fails, I can still go to Ace Hardware...

KainZero0133

About Me

Community Stats

User Tools

Posts I've Made

In Topic: New Member from Florida saying Hi

In Topic: First Homemade project.

In Topic: First Homemade project.

In Topic: First Homemade project.

In Topic: First Homemade project.

Sign In