#1
Posted 11 August 2007 - 10:39 PM
-----------------------------------------------------------------------------------------------------
Ok first step open up the Tek 10. Be careful about the cocking slide it doesn’t come off very well, or at least mine didn’t.
-----------------------------------------------------------------------------------------------------
Marvel at the odd insides for a second. Take your time taking off the turret there are three pieces that are part of it and the spring falls off and you could lose it.
-----------------------------------------------------------------------------------------------------
Once you have the turret off. Look at the front of the gun’s turret there is a small screw holding a bracing piece in. Remove the Screw and the brace should come off easily.
-----------------------------------------------------------------------------------------------------
Now take your time and pry off the turret housing from the base of the turret. Take your time and it will come off with out breaking. I used a knife blade to pry it open, just be careful if you use a knife to pry on the turret.
-----------------------------------------------------------------------------------------------------
Once you get it all pried off you will have the base with the pegs, and the turret housing. It should look something like this.
-----------------------------------------------------------------------------------------------------
Then toss the turret housing aside your not going to be needing it any more. Take the turret base and cut the pegs off of it. Try to make them relatively flush.
-----------------------------------------------------------------------------------------------------
Then reattach the brace piece you removed a little bit ago using the same screw. Make sure it is aligned properly to match up with the barrels you will be adding. Then start gluing your barrels to the gun . Use the brace as a guide. I would recommend gluing the barrel to the brace as well as the base of the turret for added strength. Be careful not to leak your glue into the inside of the turret where the spring goes. If you do take the time to clean it up, other wise the rotation mech will not work right because there is not enough resistance on the pieces for them to catch and turn.
-----------------------------------------------------------------------------------------------------
It should look something like this when you get all done.
-----------------------------------------------------------------------------------------------------\
Now just put the turret back into the gun the same way it was when you took it out.
-----------------------------------------------------------------------------------------------------
Ranges after I CPVCed this gun were astounding to me. It averaged out to about 54 Feet! Again I paced so I may be off just a little bit. I just couldn’t believe the power this has for a spring powered turret gun. It is a little bit big for a secondary but I would be tempted to use it in a war if I could get it away from my brother long enough.
Questions and comments welcome.
#2
Posted 12 August 2007 - 11:15 AM
Props
-Butt
This contest may have some flaws, as people can simply be a deuschbag over the internet. By Lying.
A war-like setting/invitational would be better...
#3
Posted 12 August 2007 - 11:30 PM
Great mod, I was never sure how to open the barrel assembly. I'm always wary of prying things apart.
#4
Posted 12 August 2007 - 11:35 PM
#5
Posted 13 August 2007 - 12:03 PM
DarkShrimp is the next Piney.
"Ignorance can be fixed. Stupidity is forever."
#6
Posted 13 August 2007 - 12:38 PM
Nice, Do Tek 10's barrel turns automatically? If it does, does it go farther than the DartTag's when PVCed?
Yes it turns automaticly, when you cock it rather then when you fire it like the Mav.
I don't own a dart tag gun so I cant tell you for sure.
#7
Posted 01 September 2007 - 10:32 PM
AWESOME NITEFINDER
#8
Posted 01 September 2007 - 11:48 PM
Edited by the beast, 01 September 2007 - 11:50 PM.
#9
Posted 02 September 2007 - 12:29 AM
Lynx dont post on a 6 month old topic you idiot.
Are you retarded?
#10
Posted 02 September 2007 - 09:42 AM
#11
Posted 03 September 2007 - 10:43 AM
Edited by the beast, 03 September 2007 - 10:44 AM.
#12
Posted 03 September 2007 - 10:56 AM
Plus i trained me mind to not think school is coming. Sorry again Lynx.
Psssh tell me about it. But school is tomorrow for me .No more waking up at 9:30.Anyway the mod will probably be better if you make your darts a bit smaller because the cpvc is a tight fit for most darts.
"Daaaamn. That's one fine looking man"
Yeah. It was scary.
#13
Posted 16 March 2008 - 06:34 PM
#14
Posted 16 March 2008 - 06:39 PM
Edited by xNFx 37, 16 March 2008 - 06:40 PM.
-Chief
#15
Posted 16 March 2008 - 06:40 PM
#16
Posted 16 March 2008 - 09:08 PM
How come all these new people dont read the coc and keep posting in old topics?
Your posts were utter shit until a few days ago so I would suggest not making worthless posts in topics you don't care about, just to complain about new people not following the rules.
Just a little advice.
#17
Posted 16 March 2008 - 09:20 PM
And what's with that FoamForce guy? He posts complementing your mod, and then gets himself banned because of his topic stating "Nerf sucks? I do not understand.
#18
Posted 16 March 2008 - 10:00 PM
This guy can see the future!
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
#19
Posted 17 March 2008 - 04:51 PM
I pitty you foo! ~MR. T
#20
Posted 17 March 2008 - 05:24 PM
Okay...
hi im new to nerf and i was wondering what size cpvc i sohould use because i have a tek 10 and was thinking of modding it
If you are using micro-sized darts (that is, ones that are about the same size as the ones that come with just about every blaster these days), then 1/2" CPVC is what you are looking for.
Really, though, you should just use whatever fits your darts well and is appropriate to the blaster and modification. For a Tek 10, that means a relatively tight fitting barrel...it should be hard to get your darts in, but not so hard that you have to jam them in. CPVC may be a little too tight, but it's not a terrible barrel material for something like a Tek 10.
Important
Also, use the shift button and punctuation! It is a rule here that we must use proper spelling and grammar. See here, and I highly suggest that you read this as well.
It's for your own benefit that you follow all of those rules.
Edited by jwasko, 17 March 2008 - 05:27 PM.
-Jwasko, STILL Sole Surviving member of Steel City Nerf and Sober Sister of the Sex Dwarves
We NERF ON all day, and FUCK OFF all night
#21
Posted 17 March 2008 - 05:31 PM
This guy can see the future!
hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns
#22
Posted 13 April 2008 - 11:37 AM
I pitty you foo! ~MR. T
#23
Posted 13 April 2008 - 11:42 AM
Also, do try to use proper capitalization. Remember, I don't make the rules, I just enforce them.
Here is a Tek 10 mod. It looks like you just unscrew the front of the turret, and then slowly pull it out, being careful to avoid losing the springs or any of the other small parts to the gun.
~ompa
#24
Posted 13 April 2008 - 04:51 PM
http://i126.photobuc...10/OpenCase.jpg
I pitty you foo! ~MR. T
#25
Posted 13 April 2008 - 04:59 PM
Without a circled picture on your part, I really can't help you much more than that. The mod pretty much tells you how to take it apart piece by piece.
And what part about proper capitalization did you not understand? Please use it. Do not force my hand. The CoC is there for a reason. I enforce it, and right now, you're really not doing a good job of following it.
You're on strike one, two more and you're gone. I will happily rescind strikes if you show a marked improvement.
~ompa
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users