13 replies to this topic

[darkness]

i cant get the trigger to work after i opened up the gun and took out the plunger and did some work on the gun

[Chewbacca]

Can we get pictures? You also have to elaborate on the description. Can you cock it? Does it stay cocked? Can you pull the trigger, but nothing happens? Or will the trigger just not budge?

Edited by Chewbacca, 13 June 2007 - 07:42 PM.

[darkness]

it wont lock up when i cock it

[l337n3rf3r]

Step 1: Throw TTG against wall.
Step 2: Drive to Toy Store.
Step 3: Buy a NF.

~l337

[Gengar003]

You have most likely done one of the following:

1.) Replaced the plunger upside-down.
2.) Added a stronger spring, such that the catch spring cannot keep the gun cocked
3.) Lost the catch spring when you opened the gun.

It is also possible, though HIGHLY unlikely, that your gun is actually broken.

Please post a picture of the internals (inside of the gun), to receive a certain answer.

Edited by Gengar003, 13 June 2007 - 08:04 PM.

[Retiate]

Open the gun back up. Check to see if either 1) The catch spring is missing. Or 2) The catch is in the wrong spot.

And, unline 1337, I like the TTG. My friend prefers his to the Nitefinder.

[darkness]

i dont know where the trigger hits the plunger thats the problem

if i cant get this to work i might put my night finder internals in the case for the ttg and the ttg internals in my night finder

and my cell phone wont connect to my laptop ( i have vista) and my cam is out of batterys.

[Carbon]

i dont know where the trigger hits the plunger thats the problem

The trigger doesn't hit the plunger. When the trigger moves backwards, it pushes the catch up out of a slot on the plunger.

From the mods section:

Another possibility from what Gengar was saying is that if you added a stronger spring, the plunger may not move back far enough to get the slot by the catch.

Edited by Carbon, 13 June 2007 - 08:32 PM.

[z80]

Also, make sure the catch plate is facing the right way. THe side with the flat tooth should be towards the back.

[bpso86]

Step 1: Throw TTG against wall.
Step 2: Drive to Toy Store.
Step 3: Buy a NF.

~l337

Blasphemy. I think you need to throw yourself against a wall, drive to store and buy yourself a brain.

My modded ttg gets great range and accuracy (actually, all of them do). Not to mention, they look and feel much better than nightfinders. They also fit in your pocket easier.

To the OP: As previously stated, spring replacement may need some trimming to fit properly. The plunger shaft could also be upside down. Look at the picture carbon posted and see if yours is facing the same direction as that one.

[hierarchy]

i dont know where the trigger hits the plunger thats the problem

if i cant get this to work i might put my night finder internals in the case for the ttg and the ttg internals in my night finder

and my cell phone wont connect to my laptop ( i have vista) and my cam is out of batterys.

That probably because vista sucks. Go mac's.

i cant get the trigger to work after i opened up the gun and took out the plunger and did some work on the gun

Ya I'm preaty sure that the catch is misplaced.

Step 1: Throw TTG against wall.
Step 2: Drive to Toy Store.
Step 3: Buy a NF.

~l337

Ya to bad the TTG is better than the NF.

[skate 4 life]

http://nerfhaven.com...t/TTallback.jpg

You see that little spring (in the pic above) up near the plunger? That probably flew out when you opened the gun up, it has happened to me numerous times. If you can't find it them you can get one out of a ball-point clicky pen. Those usually work.

Hope your gun turns into a beast!

-SKATE 4 LIFE

Edited by skate 4 life, 13 June 2007 - 11:47 PM.

[Pineapple]

darkness,
Your member account at NerfHaven has been temporarily suspended.

No one reads the warnings we post, so we've already started cleaning house. May we suggest this site to carry on from here.

Your account will not be functional until October 27, 2034 7:15pm HST (depending on your timezone). This is an automated process and you do not need to do anything to expediate the unsuspension process.


Board Address: http://nerfhaven.com/forums/index.php

[nerfer909]

Step 1: Throw TTG against wall.
Step 2: Drive to Toy Store.
Step 3: Buy a NF.

~l337

1337n3rf3r a little support for the guy would be nice, you dont have to be so harsh.