IPB

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> Ttg Modification
hierarchy
post May 8 2008, 08:41 PM
Post #1


Member


Group: Members
Posts: 354
Joined: 28-April 07
From: Port Orchard, WA
Member No.: 6537
This mod is made to relocate the plunger tube and too do other basic modifications to the TTG.

What you will need is:

thick walled PETG
PVC
1/2 inch FBR
dremel
plumbers goop/epoxy
hot glue
hot glue gun
ruler
screwdriver


Now lets get started.

First you are going to want to open your gun up and throw away the barrel and air restricter parts. You are also going to want to through away this part.
IPB Image

Now you need a barrel. So cut off a 4 1/2" segment of PETG and goop or epoxy it onto the plunger tube. It should go right over the nub on the end of the plunger. To make sure that the barrel is strait befor you glue use a little bit of hot glue to hold the barrel on strait when the goop or epoxy is drying.

While your barrel is drying it is time to work on the shell of the gun. You are going to need to dremel out the notches in the shell in the places shown below.
IPB Image

The next step is to put ammo holders on the gun. You are going to want to cut a 2 1/2" and a 2 1/4" pice of PETG. Now hot glue the larger of the two pieces into the top ammo holder spot. Then glue the smaller piece into the lower ammo holder. Now cut two 1 1/4" piece of FBR and shove them into the ammo holders. This way the darts don't go to deep into the gun on accident. It should look like this.
IPB Image

Now that your barrel is done drying you are going to want to cut a 4 1/2" section of PVC. Now dremel the inside of the PVC a little so the PVC can slide over your newly added plumbers goop. Once the PVC fits, hot glue it to the plunger so it will stay in place.

The next step is to dremel the back ring on the plunger tube. Dremel it to look like this.
IPB Image

Now you are ready to glue your plunger tube into place. This will help increase ranges because now the plunger head can do it's full range of motion in the plunger tube. You are going to want to hot glue it into this spot.
IPB Image

Next you are going to want to increase the seal on the plunger head. To do this put a few layers of e-tape under the o-ring. Make sure you wash the plunger head before doing this or the e-tape won't stick.

Now you are going to want to replace the spring. I used a RF20 spring with a stretched out NF spring over it. If you do the same spring configuration you are gong to want to stretch the NF spring to be this long so it wont rattle in the gun so much.
IPB Image
Top: RF20 spring
Bottom: NF spring

It won't rattle now because when they are on the plunger rod the RF20 spring is stopped by the plunger heads teeth and the NF spring overlaps the teeth.
IPB Image

Now your done just lube up the plunger tube and put everything together.

The ranges I got with this gun are about 75ft.

Thank you.


--------------------
QUOTE(Retiate @ Aug 13 2007, 08:43 PM) *

I guess you have some heavy duty industrial strength toilet paper holders. Do they advise you to wear eye protection when changing rolls?

My TTG mod.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
CyberPunkGunner
post May 9 2008, 07:14 AM
Post #2


Member


Group: Members
Posts: 78
Joined: 23-September 07
From: New York City
Member No.: 9893
Nice mod, clean write up and easy to follow.
I am not 100% on the strength of the RF20 spring, but from what I have heard it is beefy. I would suggest craft foam on the plunger head to increase life span on such a nicely put together gun.
Personal opinion only: Why did you waste perfectly good PETG on ammo holders that already exist? I am sure you have a reason, just can't figure it out other than "Now they won't possibly fall out".
Again, great write up.


--------------------
You were born a winner
You were the fastest sperm.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Kanashimi
post May 9 2008, 09:13 AM
Post #3


Member


Group: Members
Posts: 73
Joined: 14-December 07
From: Brooklyn Park, Minnesota
Member No.: 11781
I also say it is very clean and fairly easy to follow.
To CPG, if he is able to stuff petg into the ammo holders, then it's obvious that the holders are way to wide for his stefans. I'm guessing his darts are thin, or his TTG is the megas shooting version.

-Kanashimi


--------------------
"There's a giant mirror in front of me. How can I not act like an idiot?"
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
slowguitarman
post May 9 2008, 09:53 AM
Post #4


Member


Group: Members
Posts: 1109
Joined: 10-December 07
From: Denver, WV
Member No.: 11702
QUOTE(Kanashimi @ May 9 2008, 01:13 PM) *

I also say it is very clean and fairly easy to follow.
To CPG, if he is able to stuff petg into the ammo holders, then it's obvious that the holders are way to wide for his stefans. I'm guessing his darts are thin, or his TTG is the megas shooting version.

-Kanashimi


Yeah, the green colored one is the original mega version, so he would need the petg to keep his ammo in.

Nice job, by the way.


--------------------
QUOTE
Your dreams were tight like a baby

SGM's Shred Shop -Mod Service

NerfHaven's resident drama queen.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
oodalumps
post May 9 2008, 11:38 AM
Post #5


Member


Group: Members
Posts: 215
Joined: 29-September 06
From: Oakland County, Michigan
Member No.: 2964
Did you get the idea to relocate the tube from my writeup or independently? Anyways, pretty good mod. I'd suggest a longer barrel though.

PS: What's the plunger tube's diameter and how far can you pull the plunger rod back?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
hierarchy
post May 9 2008, 05:52 PM
Post #6


Member


Group: Members
Posts: 354
Joined: 28-April 07
From: Port Orchard, WA
Member No.: 6537
First of all thank you every one.

QUOTE(oodalumps @ May 9 2008, 12:38 PM) *

Did you get the idea to relocate the tube from my writeup or independently? Anyways, pretty good mod. I'd suggest a longer barrel though.

PS: What's the plunger tube's diameter and how far can you pull the plunger rod back?


Ya. I always was trying to find something to do with all of the dead space in the gun. And then I saw your writeup and decided to do it to me TTG.

The plunger tube's exterior diameter is about 25mm. And the interior diameter is about 23mm.

You can pull back the plunger rod 66mm.


--------------------
QUOTE(Retiate @ Aug 13 2007, 08:43 PM) *

I guess you have some heavy duty industrial strength toilet paper holders. Do they advise you to wear eye protection when changing rolls?

My TTG mod.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
OfAllTheNerf
post May 9 2008, 06:48 PM
Post #7


Member


Group: Members
Posts: 725
Joined: 6-March 07
Member No.: 5518
Nice, clean write-up. I need to get around to using my TTG as a sidearm.

-OfAll'


--------------------
[color=#FF6600][Finesse]-[BitchX]
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
chefdave
post May 9 2008, 07:13 PM
Post #8


Member


Group: Members
Posts: 346
Joined: 5-March 07
From: Camarillo, 93012
Member No.: 5495
Nice, I've done the same thing. Accept I only use the rf20 spring and it gets about 70.

Good to know some one else took my advice


--------------------
QUOTE(VACC @ Jul 21 2009, 08:13 PM) *
QUOTE(crispy) *

Talio likes to eat his own shit.
It's a distinct possibility. But seriously, that's all you could come up with? You are a terrible Troll.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Forsaken_angel24
post May 9 2008, 07:21 PM
Post #9


Member


Group: Contributors
Posts: 2360
Joined: 9-July 05
From: Mississauga, Ontario
Member No.: 1551
Nice write up.
I have to admit though, using the RF20 spring in a TTG scares the hell out of me. Be sure to let us know if this gun holds up.
Nice clean pictures too!
Consider it added.


--------------------
Who wants to take on my most entertaining brute!?!?
Go for it!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
venom213
post May 11 2008, 12:56 PM
Post #10


Member


Group: Members
Posts: 995
Joined: 11-July 07
From: Apple Valley, Minnesota
Member No.: 8004
How convienent, I just found a old style TTG at a thrift store today. I had one already, but the shell got kind of messed up. Anyway, nice mod, I plan to do something similar to mine.


--------------------
Venom's Videos

QUOTE(meatballica @ Jul 18 2010, 02:46 PM) *

Reminds me of when Ryan showed me his penis.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Silencer
post May 11 2008, 01:42 PM
Post #11


Member


Group: Members
Posts: 434
Joined: 14-February 08
From: Ridgewood, New Jersey
Member No.: 12914
Great mod and write-up, great ranges too. Good job.


--------------------
TMC
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
hierarchy
post May 11 2008, 02:32 PM
Post #12


Member


Group: Members
Posts: 354
Joined: 28-April 07
From: Port Orchard, WA
Member No.: 6537
QUOTE(Forsaken_angel24 @ May 9 2008, 08:21 PM) *

Nice write up.
I have to admit though, using the RF20 spring in a TTG scares the hell out of me. Be sure to let us know if this gun holds up.
Nice clean pictures too!
Consider it added.


Ya the teeth of the plunger head are starting to get stress marks on them. I'm going to put goop all around the teeth and see how well that holds up. I will post results later on that.


--------------------
QUOTE(Retiate @ Aug 13 2007, 08:43 PM) *

I guess you have some heavy duty industrial strength toilet paper holders. Do they advise you to wear eye protection when changing rolls?

My TTG mod.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
nerfer192
post Oct 4 2008, 05:48 PM
Post #13


Member


Group: Members
Posts: 84
Joined: 5-January 08
Member No.: 12150
QUOTE(CyberPunkGunner @ May 9 2008, 07:14 AM) *

Nice mod, clean write up and easy to follow.
I am not 100% on the strength of the RF20 spring, but from what I have heard it is beefy. I would suggest craft foam on the plunger head to increase life span on such a nicely put together gun.
Personal opinion only: Why did you waste perfectly good PETG on ammo holders that already exist? I am sure you have a reason, just can't figure it out other than "Now they won't possibly fall out".
Again, great write up.


Probably because this is the old version of the ttg, and it fires megas.


--------------------
The first time I made stefans I made them without weights.

92% of teens have moved on to the N-Strike line.
If you are part of the 8% who still use real old guns,
copy and paste this into your signature

woot I use at3k.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Blue
post Oct 4 2008, 05:57 PM
Post #14


Member


Group: Members
Posts: 1504
Joined: 7-May 08
Member No.: 14852
QUOTE(nerfer192 @ Oct 4 2008, 06:48 PM) *

QUOTE(CyberPunkGunner @ May 9 2008, 07:14 AM) *

Nice mod, clean write up and easy to follow.
I am not 100% on the strength of the RF20 spring, but from what I have heard it is beefy. I would suggest craft foam on the plunger head to increase life span on such a nicely put together gun.
Personal opinion only: Why did you waste perfectly good PETG on ammo holders that already exist? I am sure you have a reason, just can't figure it out other than "Now they won't possibly fall out".
Again, great write up.


Probably because this is the old version of the ttg, and it fires megas.


Necro.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
TheNerfLoki
post Oct 5 2008, 07:15 AM
Post #15


Member


Group: Members
Posts: 316
Joined: 15-April 08
From: NY
Member No.: 14301
QUOTE(Blue @ Oct 4 2008, 09:57 PM) *

Necro.

This is like his sixth necro in a day. Where is OMC when you need him?


--------------------
Am I the only one who uses the sig function for a sig?
TNL,
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

- Lo-Fi Version Time is now: 6th September 2010 - 03:41 PM
BoHeGeHa Dark Blue v2.2.0 by FCB-Mo
Original theme created by Tom
Invision Power Board v2.1.6 © 2010  IPS, Inc.