Jump to content


Photo

Blast Bazooka Mod

fairly easy

14 replies to this topic

#1 Arcanum

Arcanum

    Member

  • Members
  • 94 posts

Posted 18 May 2005 - 04:53 PM

The mod found here at nerfhaven is pretty good, but its rather diffucult to keep the barrel steady. If you have the materials, this should be very easy.

I started out by cutting out the unneeded part of the casing, which allows for easier loading.
Posted Image

Now grab about 5-6" of schd. 40 pvc (1/2")
Posted Image

And about 4" of class 200 1/2" pvc
Posted Image

Connect them with a 1/2" pvc coupler
Posted Image

Now add some masking tape to the bottom of the barrel to keep the removable barrel tight
Posted Image

Load your micro stock or stefan
Posted Image

Slap on your barrel, the Class 200 1/2" pvc will slip over the stock barrel. The dart will travel directly into the schd. 40 from the stock barrel if you did this correctly. You can remove this barrel to shoot the x-stream rockets.
Posted Image

The range average is about 95' but it can break 100'. This was impressive, but thats not the reason why I love this gun. It's the accuracy. The extended barrel provides quite the pin-point shot and this thing is my new primary.

Edited by Arcanum, 20 May 2005 - 09:51 PM.

  • 0
Universtiy of Illinois Fighting Illini

#2 MattPaintballer

MattPaintballer

    Member

  • Members
  • 369 posts
  • Location:Where the slots are plentiful, and the yards are small

Posted 18 May 2005 - 05:07 PM

Nice mod. I like how you can still shoot the X-Stream rockets - one reason I usually don't mod my guns that shoot larger ammo.

What do you mean by regular 1/2" PVC?
  • 0
"I think politicians are much more irritating than hippies."
"the56ace,
Your member account at NerfHaven has been temporarily suspended because I don't like you."
-cxwq
If ignorance is bliss, our president must be ecstatic.

#3 Arcanum

Arcanum

    Member

  • Members
  • 94 posts

Posted 18 May 2005 - 05:10 PM

well for some reason, my menards carries pvc with pink lettering. It is 1/2" diameter measuring from the outside edges, but the inside diameter is larger than schd. 40 pvc would normally be. If you can't find any in your area, you can always purchase some from me.
  • 0
Universtiy of Illinois Fighting Illini

#4 flashflint

flashflint

    Member

  • Members
  • 606 posts
  • Location:Michigan, 49240

Posted 18 May 2005 - 06:25 PM

Nice mod but with mine I just opened it up and cut the front about 2/3 of an inch off the barrol it gets about 100 feet with 1/2 inch stefans. And can still shoot the big rocket. :P
  • 0

#5 MattPaintballer

MattPaintballer

    Member

  • Members
  • 369 posts
  • Location:Where the slots are plentiful, and the yards are small

Posted 18 May 2005 - 06:33 PM

His shoots mega Stefans (made of 5/8" foam) though. I personally like megas better.
  • 0
"I think politicians are much more irritating than hippies."
"the56ace,
Your member account at NerfHaven has been temporarily suspended because I don't like you."
-cxwq
If ignorance is bliss, our president must be ecstatic.

#6 cxwq

cxwq

    Member

  • Founders
  • 3,634 posts

Posted 18 May 2005 - 06:48 PM

It is 1/2" diameter measuring from the outside edges, but the inside diameter is larger than schd. 40 pvc would normally be.

If the ID is larger than 1/2" SCH40 would be (5/8") then the OD must be greater than 1/2".
  • 0
<meta name="cxwq" content="mostly water">

#7 WEASEL

WEASEL

    Member

  • Members
  • 145 posts
  • Location:California

Posted 18 May 2005 - 06:52 PM

And about 4" of REGULAR 1/2" pvc
Posted Image

Can anyone say Class 200?
  • 0

#8 SneakUP

SneakUP

    Member

  • Banned
  • 79 posts

Posted 18 May 2005 - 07:19 PM

Nice mod, it reminds me of the titan reduce mod and also did you plug pump for it to reach 95' ,and was it angled?
GOT FOAM?!

#9 Uncle Hammer

Uncle Hammer

    Member

  • Members
  • 750 posts
  • Location:Austin,TX 78758

Posted 18 May 2005 - 07:19 PM

Nice mod fairly simple and easy, and great ranges. I bet a micro could get a good 110'.
  • 0
Don't mess with Texas cuz its bigger than France, bitch..
QUOTE (Talio)
Catagory 5 hurricanes are the mighty dick of God.  You don't mess with that!  You don't mess with Gods dick!

#10 Arcanum

Arcanum

    Member

  • Members
  • 94 posts

Posted 19 May 2005 - 10:51 AM

No I did not plug the pump, and yes that was a level shot.

I'm sorry I don't have any more info but the side simply reads 1/2" pvc in pink lettering, while my other one reads, schd. 40 1/2" pvc in blue lettering

Edited by Arcanum, 19 May 2005 - 10:53 AM.

  • 0
Universtiy of Illinois Fighting Illini

#11 duce

duce

    Member

  • Members
  • 342 posts
  • Location:Ann Arbor MI (southeast MI)

Posted 19 May 2005 - 04:30 PM

Nice clean mod. I've been meaning to pick one of these bad boys up, and for just ten bucks it seems like a great deal. The only thing I don't like is having the pump in the back like the Titan.
  • 0
"Thats so good it makes me want to kick my mom in the face." -Halfling

#12 Arcanum

Arcanum

    Member

  • Members
  • 94 posts

Posted 19 May 2005 - 06:35 PM

It is 1/2" diameter measuring from the outside edges, but the inside diameter is larger than schd. 40 pvc would normally be.

If the ID is larger than 1/2" SCH40 would be (5/8") then the OD must be greater than 1/2".

I see what you're saying, but it fits in the coupler...I'm baffled.
  • 0
Universtiy of Illinois Fighting Illini

#13 cxwq

cxwq

    Member

  • Founders
  • 3,634 posts

Posted 19 May 2005 - 07:00 PM

No worries, as already mentioned by WEASEL it's cl200 PVC which is lower pressure rating so it's got a larger ID but the same OD. Not particularly useful as a barrel, but it might be good for structural support (like this) in other mod situations. I'll have to keep it in mind.
  • 0
<meta name="cxwq" content="mostly water">

#14 NinjZ

NinjZ

    Member

  • Members
  • 1,005 posts
  • Location:jersey

Posted 19 May 2005 - 07:18 PM

I agree with Cx, very good idea for nesting and structural support.

Nice mod too.
  • 0

#15 Shaggyman15

Shaggyman15

    Member

  • Members
  • 9 posts

Posted 19 May 2005 - 08:35 PM

Hey arcanum. Could you possibly help me out on this mod this weekend. I ran into a problem. I kinda cut too close to the trigger so i might need your help. And i need the PVC and all that stuff. Maybe after the ht. Thanks
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users