13 replies to this topic

[mayhem]

Here's my double barreled secret shot, I liked the look of two barrels better than 3, plus I botched up my last triple barrel mod, I didn't want to mess with it.


A front view: the 2 barrels with darts in them.

Edited by mayhem, 24 April 2005 - 02:32 PM.

[duce]

Nice job there, very clean looking. Hows about some rizzanges?

[1313]

Looks very good, do the two darts spread? And if so how far? What about ranges? And did you join two pieces of cpvc together for the barrel? That looks cool but I would worry about air escaping between the darts.

[Spaztic 75]

It's good to see someone using a SSI for a change, they never seem to get enough credit.

[MattPaintballer]

That's a nice mod, and it's very clean. Well done. Does it shoot both darts at the same time, or can you switch between the two barrels? That would be schweet.

I remember my friend got a set of those at a garage sale for three bucks, we would play with them for hours... I don't know whatever happened to those, I should ask him. That was like, the best gimmicky gun ever. We would spend hours acting like James Bond with the pistols touching our heads, sneaking along the walls, then shooting out of the handle instead of the main barrel. Good times .

[Airsoft999]

That's a nice mod, and it's very clean. Well done. Does it shoot both darts at the same time, or can you switch between the two barrels? That would be schweet.

Well the ammo-holder is clicked either up or sideways, allowing that certain barrel to shoot (as you probably know) but I think you can have it half-and-half, but it would be weak.

[mayhem]

Oh yeah, I guess it does look confusing.

It still uses the gimmick, I just added a barrel to the original primary barrel.
And then I cut of the tube of the secondary one, but left about 1,5 inches and attached a barrel to that too. By leaving the clear tubing on, I could point the bottem barrel whereever I wanted and then tape it to the top one to keep it in the place.

So the barrel assembly is:
-Two Micro-pvc barrels against eachother.
-Then 2 Mega-pvc tubes cut in half and put on either side and then taped together. This hides the suctioncaps and makes the barrelassembly look better.

Ranges are about 50 ft without rubberbands.

[LordoftheRing434]

That is really schweet. I've got a SS1 I used forever. But then my NF came into play, and it hasn't had much attention since. Maybe if I did a nice mod like this, I would bring it out again.

[kickass jb]

I am a huge fan of my SSI. I single barreled pvc modded it (took out the separater thing and glued the barrel directly to the plunger tube). I took the idea from this site's EaB mod and put the size tubes around the barrel for ammo holders. Good ROF and gets about 30-40 ft. GREAT for indoor wars, I even use it ahead of my Sharpshooter 2. I will add some pics of it as soon as I figure out how to post them.

Edited by kickass_jb, 28 April 2005 - 02:36 PM.

[kickass jb]

SS1 open

SS1 barrel

Here are two pics of my modded SS1 I mentioned above. For the plunger tube, I plugged up the hole with hot glue that's at the top and made a hole about the same size dead center in the tube. I clamped the pvc to the plunger tube for stability then hotglued it up lightly and then a thin layer of duct tape.

[Jakethesnake]

30-40 ft? I just single barreled mine (cpvc) and it gets 60 ft flat, it's amazing, I like it better than nite finders.

[kickass jb]

Jake, are you using megas or micros?

[Jakethesnake]

Micros, they fit super tight in the barrel if that has anything to do with it. (I think it does)

[kickass jb]

That's probably it because I'm using megas (buying micro stuff tonight). So hopefully when I switch over to micros, I'll see better results.