Jump to content


Photo

Nerf Hyperfire Complete Internal Teardown, Review, and Chronograph Dat

Hyperfire internals

5 replies to this topic

#1 Duke Wintermaul

Duke Wintermaul

    Member

  • Members
  • 516 posts

Posted 30 April 2016 - 03:16 AM

This post was intended to serve as an in-house troubleshooter and Internal Guide for the Internal Directory of the new Nerf N-Strike Elite Hyperfire, far different than the current Hyperfire.
For more information on the New Hyperfire see my upcoming modification guide. 

NwTfirL.jpg

The Hyperfire has 20 screws in it's main body, the four in the conveyor belt do not need to be removed before disassembly.

GNfxeLy.jpg
 
The main board is right behind the battery tray in the stock, it houses the thermally sensitive resistor and various other components.

HSO96cE.jpg
 
The main body of the blaster houses many triggers and electrical switches.

5nD999R.jpg
 
Without all of that nasty orange plastic in the way we can get a clear view of how the electrical system is layed out.
 
yTgxcZo.jpg
 
The flywheel housing and the conveyor belt in their proper location.

Ju95nDr.jpg
 
The conveyor belt internals. There is no reason to disassemble the "Jam Belt". I was originally mistaken, there are two prongs on the belt which means the conveyor is rotating 2.5 times a second.

tjP1ixf.jpg

And this is the lock that breaks the circuit if the switch on the Jam Belt is not engaged.

soFcNiX.jpg
 
The inside of the pusher box that powers the belt.

m1Ok7Ua.jpg

The integrated board on the canted flywheels.

ywLT97k.jpg
 
The canted wheels inside the cage.

v6hWi5M.jpg
 
A fully disassembled flywheel cage. 
 
yQ6z83E.jpg
 
The Electrical system of the blaster, in it's proper location.

kTzRzVe.jpg
 
The Electrical system of the blaster... completely removed.

5vz8Pll.jpg
 
The blaster with all internals removed.

0lna0GG.jpg
 
And now were going to completely disassemble the shell. First thing to do is remove all the loose components from the blaster.

asWEf81.jpg
 
There are five screws inside the blaster, all located on the grey main plate. Remove all ten and the blaster will easily come apart into different sections. Below is the grey main plate.

y0F7uRd.jpg
 
And here is the blue and orange plates, which both connect to the grey main plate. The blue plate must be removed first, meaning that the orange plate must be place back into the grey plate first.

eSiMpsr.jpg

And that's pretty much the blaster. I trust people will be able to solve their misplaced piece syndrome with the above catalog, and the full disassembly will help users to properly paint their blasters.

Below is a set of Chronograph Muzzle velocities from the Stock Hyperfire using the Stock Fresh Y-code Elite Darts that were included with the blaster. The numbers are, hopefully obviously, feetpersecond muzzle velocities. Each shot was taken at a full spinup of the flywheels, using full auto will drastically reduce these numbers.

lohfiRQ.png

I guess I promised you a review in the title? I hope this embedding works...
 


Edited by Duke Wintermaul, 30 April 2016 - 11:39 PM.

  • 0

#2 shandsgator8

shandsgator8

    Member

  • Members
  • 603 posts

Posted 30 April 2016 - 11:19 AM

I had heard about canted flwyheels, but didn't know what that meant until your pics; thanks for that. But what's the advantage of using canted flywheels?


  • 0

#3 The2ndBluesBro

The2ndBluesBro

    Member

  • Members
  • 576 posts

Posted 30 April 2016 - 11:27 AM

I had heard about canted flwyheels, but didn't know what that meant until your pics; thanks for that. But what's the advantage of using canted flywheels?

More accurate, but I don't know if anyone has tested it extensively. Gives the dart some spin, like rifling.
  • 0

Nerf, Gaming, knives: https://www.youtube....FjcObRZTl2KReDQ

 


#4 Kilomona

Kilomona

    Member

  • Members
  • 108 posts

Posted 30 April 2016 - 03:43 PM

Does the conveyor belt run on seperate motors? If so, people could speed up or slow down the rate of fire as desired by adding new motors.

Edited by Kilomona, 01 May 2016 - 08:49 AM.

  • 0

#5 Zombona

Zombona

    Member

  • Members
  • 56 posts

Posted 01 May 2016 - 06:18 AM

Does the comveyor belt run on seperate motors? If so, people could speed up or slow down theor rate of fire as desired by adding new motors.

 

The feeding mech motor is not 130 sized so there isn't a drop in solution discovered right now.


  • 0

#6 CaliforniaPants

CaliforniaPants

    Futtbrustrated

  • Moderators
  • 459 posts

Posted 01 May 2016 - 03:07 PM

I wouldnt have expected all the blue bits to come off, I'm guessing it all still works without that stuff on. also a sort of weird question, but is it comfortable for not child size hands?


  • 0

trans as shit because fuck you




Also tagged with one or more of these keywords: Hyperfire, internals

1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users