Jump to content


Photo

110FPS BOOMco Plasma Pistol Post-Modification Writeup


8 replies to this topic

#1 Duke Wintermaul

Duke Wintermaul

    Member

  • Members
  • 516 posts

Posted 01 April 2016 - 02:44 PM

Having a little trouble with one of my Plasma Pistol's triggers, so since I have to take it apart I figured I'd do a quick write up on how I disassembled this blaster (which seems to be a trouble point with most users) and the modifications I performed. 

Fmkn5rY.jpg

Tool's required:
T15 or T10 hex bit
Size 1 screwdriver. The screws are Phillips, but I used a Standard.
Hammer
Replacement spring or a duplicate stock spring.
Wire Cutters (optional)
Hotglue or similar adhesive

Step #1: Removing the main rivet.
 

Place your hex bit firmly on the threaded side of the rivet (the side without screw holes) and give it a solid whack with your hammer. One nice big whack is all you'll need.
 

OHCrxqm.jpg

 

The rivet will protrude from the other side and can easily be grasped with your fingers and removed.

 

tIppFIJ.jpg

 

Step 2: Removing the secondary rivet.

This is why I'm using a Standard driver. Take your driver and position it as shown, use steady and gentle pressure to pop one side of the rivet out of it's housing.

p7JHZmi.jpg
 

At this point you need to remove the two screws in the top of the slide. Once done, the slide can be removed. There is a third rivet at the very base of the slide, but it is not necessary to remove in order to get the slide off. If you wish to remove it take your wire cutters and either snip the rivet in half or use gentle pressure to pop it off. Remove said slide. 

Step 3: Disassembly

There are twelve screws that need to be removed. Do so.

 

ZPIbc31.jpg

 

Step 4: Internal modification.

This is what you're finished internals will look like.

 

PzWcck1.jpg

 

There are three pieces of plastic that need to be removed, they make up the dart lock that prevents you from pulling the trigger if a dart is not loaded. They consist of the cap, black lock, and actuator arm. Remove all three of these. Below photo of the stock internals to show the locks, photo credit Zombona (Thanks, Google)

zAwoqV0.jpg
 

Now were going to plug the hole in the barrel that was used for this lock. Simple to do, just fill it up with hotglue or an adhesive of your choice. Be sure the barrel is filled with either a dart or tube of similar diameter.

X9sxsDT.jpg

Swap out the spring and put it back together.

Enjoy your new pistol.

9O59Qb8.jpg?1zR2D4si.jpguQUqSUV.jpg


Edited by Duke Wintermaul, 11 April 2017 - 07:05 PM.

  • 0

#2 Ice Nine

Ice Nine

    Prince Dangus

  • Administrators
  • 1,460 posts

Posted 01 April 2016 - 04:56 PM

Neat mod. How hard is it to replace the priming bar once you've popped it out? Does removing it noticeably stress the plastic that's supposed to grip the ridged metal?


  • 0

Unholy Three: DUPLUM SCRTA, DUPLUM PROBLEMA (2009)

But Zeke guns tend to be like proofs by contradiction

Theoretically solid but actually non-constructive

Rnbw Cln


#3 Buffdaddy

Buffdaddy

    Do not buy from this member

  • DO NOT TRADE
  • 824 posts

Posted 01 April 2016 - 06:44 PM

Neat mod. How hard is it to replace the priming bar once you've popped it out? Does removing it noticeably stress the plastic that's supposed to grip the ridged metal?

 

As another person with experience modding these, as long as you're careful in removing and replacing the priming bar, there's no noticeable stress in the plastic in that area.


  • 0

#4 Duke Wintermaul

Duke Wintermaul

    Member

  • Members
  • 516 posts

Posted 01 April 2016 - 08:56 PM

The blaster shown has been disassembled at least four times. If you follow my above method there is no stress to the plastic and the rivet can be removed and replaced as many times as you wish. 


  • 0

#5 Duke Wintermaul

Duke Wintermaul

    Member

  • Members
  • 516 posts

Posted 23 April 2017 - 08:34 PM


  • 0

#6 Dutch

Dutch

    Member

  • Members
  • 13 posts

Posted 24 April 2017 - 04:00 PM

what spring did you use??


  • 0

#7 Duke Wintermaul

Duke Wintermaul

    Member

  • Members
  • 516 posts

Posted 24 April 2017 - 08:13 PM

I order bulk custom made springs from Hillmann. They work in over half a dozen BOOMco blaster with high velocity results.

Farshots/M6/Plasma Pistols achieve 120feetpersecond with them.

They are $5 per, PM me if you would like to buy one.


  • 0

#8 Speedr117

Speedr117

    Member

  • Members
  • 57 posts

Posted 25 April 2017 - 07:33 AM

Are these hillmen springs the same as the ace hardware #54/#49 spring thought it was something like hillman.
  • 0

#9 Dutch

Dutch

    Member

  • Members
  • 13 posts

Posted 25 April 2017 - 03:24 PM

apparently the stock catch spring can take a [k26]. if thats too much go for a [k25]
  • 0


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users