Jump to content


Photo

noobs strayven overhaul no imrs or lipos


5 replies to this topic

#1 xXD3V1LXx

xXD3V1LXx

    Member

  • Members
  • 258 posts

Posted 20 March 2016 - 05:12 PM

Hi as an intro I should say this is great for younger audiences it is super easy and fun to do.

Here is how to make a strayven or any integration the easy way. Note this is just the first part I am not done I will be showing how to do the bondo this Friday.

So I had a gutted ray even and a stryfe both not performing at peak so I decided to make a strayven. But this strayven doesn't take imrs it takes 7 aas and a wire soldered at each end to act as a dummy battery. So noobs can get an overhaul without having to invent money in expensive lipos and chargers.

So first Your going to gut your blasters.
image.jpeg


Next line your blasters up. This is so you know where to cut.
image.jpeg


Now draw lines that are visible for cutting
image.jpeg


Now go ahead chop that baby up!
image.jpeg
image.jpeg

Now line up the shells and hot glue them together temporarily. BUT MAKE SURE TO DO EACH HALF SEPARATE OR CUT THE MIDDLE AFTERWARDS OTHERWISE IT WONT WORK!
image.jpeg

Now install internals but make sure to wire up the battery trays in series( bring negative wire from Raven shell and attach that to motor than attach the positive from the Raven to the negative on the stryfe, than from the positive on the stryf to the rev switch than to the motor housing.
image.jpeg

Now put the two halves back together and you are done with part one.

 

post-122764-0-34716600-1459459975_thumb.jpeg

Get that bondo out

post-122764-0-12806300-1459460021_thumb.jpeg
That little dot is all the hardener you need.

 

post-122764-0-56530400-1459460139_thumb.jpeg
Now apply the bondo. Go as heavy as you please just know you have to sand it down afterwords.

Sand it down paint it and you are all ready to go. I'll post mine once I am done painting it.


Edited by Snoop Doggy doge, 01 April 2016 - 09:18 AM.
Please keep all of your writeup together,

  • 0
A quote from Ice Nine
"Use the golden rule: Don't be a dick."

NERF On
-Devil

#2 Snoop Doggy doge

Snoop Doggy doge

    Fig you, Van

  • Members
  • 501 posts

Posted 20 March 2016 - 05:33 PM

FPS?


  • 0

#3 xXD3V1LXx

xXD3V1LXx

    Member

  • Members
  • 258 posts

Posted 20 March 2016 - 05:43 PM

Not done yet but hitting the wall pretty hard ild say maybe 90-110

Edited by xXD3V1LXx, 20 March 2016 - 05:44 PM.

  • 0
A quote from Ice Nine
"Use the golden rule: Don't be a dick."

NERF On
-Devil

#4 Remzak

Remzak

    Member

  • Members
  • 94 posts

Posted 22 March 2016 - 05:17 AM

That is not hitting 90-110 fps.Maybe 90-100 fps. 110 fps is close to the bleeding edge for stock flywheels.
  • 0
Unnoficial "Drone" Expert

#5 xXD3V1LXx

xXD3V1LXx

    Member

  • Members
  • 258 posts

Posted 22 March 2016 - 06:03 AM

Typo didnt see that
  • 0
A quote from Ice Nine
"Use the golden rule: Don't be a dick."

NERF On
-Devil

#6 xXD3V1LXx

xXD3V1LXx

    Member

  • Members
  • 258 posts

Posted 31 March 2016 - 04:36 PM

image.jpeg

Get that bondo out

image.jpeg

That little dot is all the hardener you need.

Now apply the bondo. Go as heavy as you please just know you have to sand it down afterwords.
image.jpeg

Sand it down paint it and you are all ready to go. I'll post mine once I am done painting it.

I put this in the main thread, please edit it next time and add onto the original post.


Edited by Snoop Doggy doge, 01 April 2016 - 09:21 AM.

  • 0
A quote from Ice Nine
"Use the golden rule: Don't be a dick."

NERF On
-Devil


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users