Jump to content


Photo

ZombieStrike Stormfire Plunger Replacement


5 replies to this topic

#1 The lord of fish

The lord of fish

    Member

  • Members
  • 76 posts

Posted 24 August 2014 - 05:27 PM

Preface: I stopped building guitars as I found the atmosphere to be pretty negative. My earlier posts reflected such negativity and as much as I'd like to apologize for the asshattery, its a few years too late. Now I'm back to just doing cad for hire.

I never saw/used the original dart tag stormfire. Its a night finder with much improved ergonomics and no gimmicky light. It's also a good deal bigger.

Materials needed:
Epoxy/Super glue/ solvent weld
1x Everbilt spring (or a spring of your choice IE cutdown [k26])
1x 1" drain plug
1x 1" small screw
1x 3/4" to 1/2" PVC reducer/bushing
1x 1 1/4" drain extension.
A fine tooth saw, or your favorite cutting tool.
a screw driver.

Optional:
some grub screws
thread locker
and a drill bit that corresponds with whatever grub screws you bought.

It comes with a gimmicky acog looking hollow tube of a scope. I threw that away. Stock I was hitting about 40 feet barely.
Posted Image

First start by unscrewing the orange muzzle cap
Posted Image

Then unscrew the slide.
Posted Image

Now unscrew the gun, the catch spring might fly out, so be careful.
Posted Image

Remove the internals, and sand the muzzle end of the shell until there are no more ridges
Posted Image

Now unscrew, and take apart the plunger head.
Posted Image

take your drain plug and cut the keyring tab off with a razor or sharp knife. I punched a hole in the center with my screw driver.
Posted Image

slip the bottom section of the stock plunger head into the drain plug.
Posted Image

Slide your everbilt spring and then screw the new plunger head on using a small screw, I used a 1" wood screw.
Posted Image

Cut the shell along these lines, right before the top rail thickens for nstrike attachments, and along the gray horizontal.
Posted Image

Cut the drain tube to 4"
Posted Image

Apply silicone grease/ your lube of choice and slide it over the plunger rod. Then glue the plunger tube directly to one side of the shell.
Posted Image
You can close it all up now. I like the slide over the standard pull handle of a NF, so I kept it on, otherwise you could leave the slide off and attach a key ring if you fancy.
Posted Image
With a 5" cpvc barrel I was hitting between 85 and 93 feet out of 4 shots.

I'd recommend screwing the plunger tube to the shell as well, but I didn't have the materials. My old NF rifles from 2011 have held up being solvent welded to one side of the shell, but mechanical attachment is definitely more convenient and allows for easier maintenance

Edited by The lord of fish, 24 August 2014 - 05:37 PM.

  • 0
Do you think she'll sleep with a panic switch?

#2 TheNerfingFlamingo

TheNerfingFlamingo

    Member

  • DO NOT TRADE
  • 91 posts

Posted 24 August 2014 - 05:41 PM

Edit: I found what i was looking for, sorry.

Edited by TheNerfingFlamingo, 24 August 2014 - 05:43 PM.

  • 0
I killed a man with my titan.

#3 The lord of fish

The lord of fish

    Member

  • Members
  • 76 posts

Posted 24 August 2014 - 05:43 PM

Slide your everbilt spring and then screw the new plunger head on using a small screw, I used a 1" wood screw.


  • 0
Do you think she'll sleep with a panic switch?

#4 Zorns Lemma

Zorns Lemma

    Sir Scrt

  • Moderators
  • 1,277 posts

Posted 24 August 2014 - 06:14 PM

Welcome back, good to see that you're back to strapping new plunger tubes to "pistols."
  • 0
"In short, the same knowledge that underlies the ability to produce correct judgement is also the knowledge that underlies the ability to recognize correct judgement. To lack the former is to be deficient in the latter."
Kruger and Dunning (1999)

#5 The lord of fish

The lord of fish

    Member

  • Members
  • 76 posts

Posted 24 August 2014 - 06:28 PM

Haha, I suppose you shouldn't expect too much, I like making pseudo home-made abomination "pistols" far too much.
  • 0
Do you think she'll sleep with a panic switch?

#6 Pineapplepies

Pineapplepies

    Member

  • Members
  • 150 posts

Posted 22 October 2015 - 12:11 PM

Looks pretty neat, although you could use a pvc tee, small piece of pvc and a end cap to make a handle if you want to make it like a rifle.

Edited by Pineapplepies, 22 October 2015 - 12:11 PM.

  • 0
<p>It's nerf or...... every other blaster brand that is better 

Darth nerf "I used to like the deploy, I ''twas but a learner, now I am the master" Obi buzz bee kenobi "only a master of nerf evil darth"


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users