Jump to content


Photo

Rscb Valve Clip

timings a bitch but ooo so wonderful when it works

11 replies to this topic

#1 Mr BadWrench

Mr BadWrench

    Member

  • Members
  • 781 posts
  • Location:Bum Funk Ohio

Posted 10 June 2009 - 08:46 PM

Posted Image

here is my 4b with RSCB and experimental valve.

Posted Image
simple wood dowel with chunk cut out of it.... the tighter the fit the better, but it has to move completely freely.
Posted Image
drop wood dowel into RSCB tee

Posted Image

Posted Image

When blaster fires valve is pushed upwards trapping darts from shooting out.... only dart in barrel will fire.


Don
  • 0
NerfChat IRC Chatroom Click to chat!

#2 nerkum

nerkum

    Member

  • Members
  • 171 posts
  • Location:Georgia, USA
  • State:Georgia
  • Country:United States

Posted 10 June 2009 - 09:03 PM

Absolutely Brilliant. If we can find a way that it seals off the back part of the barrel then we wouldn't have all the extra dead space created by the rest of the RSCB clip. Then you would have the best of both worlds, high ROF and top notch ranges.

I will definately be trying this on my next Mod, since the dead space issue was really bugging me.
  • 0

#3 TantumBull

TantumBull

    Member

  • Moderators
  • 1,929 posts
  • Location:Seattle, WA
  • State:Washington
  • Country:United States
  • u/LukeKoboJobo on Reddit

Posted 10 June 2009 - 09:14 PM

nerkum: You realize this doesn't do anything about deadspace, right?

Badwrench: Do you get double fires often? It rarely happens to me. I understand this could be useful if you get double fires often.
  • 0

#4 nerkum

nerkum

    Member

  • Members
  • 171 posts
  • Location:Georgia, USA
  • State:Georgia
  • Country:United States

Posted 10 June 2009 - 09:23 PM

TantumBull: Yes, I know the mod in its current state does nothing about the dead space, but I see this as a huge leap for that to be accomplished.

The wood dowel pops up into the barrel to block the second dart loaded from going out the barrel as well. I don't see why we cannot take it a step further and stop air from going into the deadspace of the clip.
  • 0

#5 cheesypiza001

cheesypiza001

    Member

  • Members
  • 752 posts
  • Location:Connecticut

Posted 10 June 2009 - 09:38 PM

Does this hinder the airflow at all?
  • 0

#6 Mr BadWrench

Mr BadWrench

    Member

  • Members
  • 781 posts
  • Location:Bum Funk Ohio

Posted 10 June 2009 - 09:54 PM

Does this hinder the airflow at all?

Its a 4b..... 1 more pump and all is fine.
  • 0
NerfChat IRC Chatroom Click to chat!

#7 TantumBull

TantumBull

    Member

  • Moderators
  • 1,929 posts
  • Location:Seattle, WA
  • State:Washington
  • Country:United States
  • u/LukeKoboJobo on Reddit

Posted 10 June 2009 - 10:17 PM

The wood dowel pops up into the barrel to block the second dart loaded from going out the barrel as well. I don't see why we cannot take it a step further and stop air from going into the deadspace of the clip.


Oh we definitely can, its just that air particles are a hell of a lot smaller than a stefan.
  • 0

#8 Hipponater

Hipponater

    Member

  • Members
  • 297 posts
  • Location:Madison, WI
  • State:Wisconsin
  • Country:United States

Posted 10 June 2009 - 10:37 PM

I'll take the hint, Badwrench, and add it to my RSCB BBBB that was shooting all the darts... (actually, I don't think my friend was using it right).

I really like the design, works well. I'll try this out on my PAS with an rscb and see if it hinders anything, but on a BBBB there's so much air it won't make a difference.

I think a fully (or mostly) deadspace blocking piece would be do-able. You could add a flare or something on the back of the dowel to block out the tube, then dremel out the T coupler to allow the flare to drop down with the dowel to allow the next dart forward.

Looks good, I'll be sure to try it out.
  • 0

#9 wohnson89

wohnson89

    Member

  • Members
  • 70 posts
  • Location:Wichita, KS
  • State:Kansas
  • Country:United States

Posted 19 September 2009 - 09:40 AM

Nice job i must say. I will be attempting this when i get a chance. By the way what kind of barrel material did you use? It looks like 1/2 in. cpvc, but for some reason the kind that i tried won't even fit my darts.(i use the stock longshot darts and stefan's of the same size.) Would brass work? Sorry im asking probably very stupid, and easy to answer questions, but im relitivly new at nerf.
Thanks.
  • 0
Make it idiot proof and someone will make a better idiot.

1992 Subaru SVX- My Baby


#10 jerm78

jerm78

    Member

  • Members
  • 243 posts

Posted 19 September 2009 - 12:23 PM

brilliant!
  • 0

#11 Mr BadWrench

Mr BadWrench

    Member

  • Members
  • 781 posts
  • Location:Bum Funk Ohio

Posted 19 September 2009 - 07:44 PM

you have to find material that fits your darts

you can do any mod with any material if you plane carefully and have some clue as to what you want the outcome to be..

i use 1/2in cpvc and I shoot streamlines out of my RSCB longshot.


take darts to the store when you buy barrel material... I get mine at lowes.... just did through all the pipe they have till you find a piece that the dart fits into both ends.

Don
  • 0
NerfChat IRC Chatroom Click to chat!

#12 wohnson89

wohnson89

    Member

  • Members
  • 70 posts
  • Location:Wichita, KS
  • State:Kansas
  • Country:United States

Posted 20 September 2009 - 01:02 AM

Thanks for the help. I looked and 9/16 brass works well for me. B)
  • 0
Make it idiot proof and someone will make a better idiot.

1992 Subaru SVX- My Baby



0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users