Jump to content


Photo

Ls Dart Tooth

Should I keep it?

10 replies to this topic

#1 Rec0n Industries

Rec0n Industries

    Member

  • Members
  • 23 posts

Posted 10 June 2009 - 07:43 PM

I use The bbb+silver Ls spring combo. I'm planning on doing a Pvc barrel replacement. I've searched 5 times, and found nothing. Should I keep the dart tooth?
  • 0
WIP: Flak Z-35 Heavy assault rifle

#2 nerfer63

nerfer63

    Member

  • Members
  • 386 posts
  • Location:fair oaks, CA

Posted 10 June 2009 - 08:13 PM

I use The bbb+silver Ls spring combo. I'm planning on doing a Pvc barrel replacement. I've searched 5 times, and found nothing. Should I keep the dart tooth?



Are you singling it? If not then no dart tooth I think.
  • 0

#3 Rec0n Industries

Rec0n Industries

    Member

  • Members
  • 23 posts

Posted 10 June 2009 - 08:14 PM

I am keeping the clip.
  • 0
WIP: Flak Z-35 Heavy assault rifle

#4 X RUSHED X

X RUSHED X

    Member

  • Members
  • 32 posts

Posted 10 June 2009 - 08:21 PM

Are you singling it? If not then no dart tooth I think.

If you single it, you can't keep the dart tooth. You replace the bolt and barrel/dart tooth with a CPVC coupler or T-coupler.

Rec0n Industries, if you are keeping the clip, keep the dart tooth. The absence of one causes a small amount of air to escape the hole where it used to lock into place. If any of my facts were wrong, please correct me.

Edited by X RUSHED X, 10 June 2009 - 08:22 PM.

  • 0
QUOTE(Hipponater @ Oct 7 2009, 05:34 PM) View Post

If it feels hard to pump, stop.


#5 Russ T Bullet

Russ T Bullet

    Member

  • Members
  • 23 posts
  • Location:Hernando, MS

Posted 10 June 2009 - 08:27 PM

Actually, I believe the dart tooth pushes the dart into the barrel. Without it, the dart won't go into the barrel all the way, causing less of an air tight seal.

So yes, if "cliped" keep the dart tooth.
  • 0
I'll take my guns and money; you keep your "change".

#6 happybiscuit

happybiscuit

    Member

  • Members
  • 15 posts

Posted 10 June 2009 - 08:28 PM

Are you singling it? If not then no dart tooth I think.

If you single it, you can't keep the dart tooth. You replace the bolt and barrel/dart tooth with a CPVC coupler or T-coupler.

Rec0n Industries, if you are keeping the clip, keep the dart tooth. The absence of one causes a small amount of air to escape the hole where it used to lock into place. If any of my facts were wrong, please correct me.

The dart tooth is used to push the dart into the real barrel(the one that moves). There is no seal with the fake barrel even with the dart tooth.

Edit: Dang it, you beat me to it.

Edited by happybiscuit, 10 June 2009 - 08:30 PM.

  • 0
[size=4][font=Times New Roman] I'm only the appetizer.

#7 X RUSHED X

X RUSHED X

    Member

  • Members
  • 32 posts

Posted 10 June 2009 - 08:41 PM

Edit: Sorry guys. Misunderstood his post.

Edited by X RUSHED X, 10 June 2009 - 08:42 PM.

  • 0
QUOTE(Hipponater @ Oct 7 2009, 05:34 PM) View Post

If it feels hard to pump, stop.


#8 Rec0n Industries

Rec0n Industries

    Member

  • Members
  • 23 posts

Posted 10 June 2009 - 09:34 PM

Thank you. I'll keep it then.
  • 0
WIP: Flak Z-35 Heavy assault rifle

#9 wingd man

wingd man

    Member

  • Members
  • 514 posts
  • Location:Austin,TX 78751

Posted 10 June 2009 - 11:25 PM

I'm planning on doing a Pvc barrel replacement.


What do you mean PVC barrel replacement? If you mean CPVC then you must be singling it, but you're not so... specify?
  • 0

#10 Rec0n Industries

Rec0n Industries

    Member

  • Members
  • 23 posts

Posted 10 June 2009 - 11:54 PM

I'm going to try to make a barrel replacement out of Pvc, to give my streamlines more accuracy. Basicly, I'm trying out a barrel matieriel that I haven't seen used before in a Ls. I'm also going to put a piece of Pvc in the part of the bolt that holds the dart, so the dart can stay centered and i can rip out the piece that the peg is connected to, to give full air flow.

Does this make sense?
  • 0
WIP: Flak Z-35 Heavy assault rifle

#11 SchizophrenicMC

SchizophrenicMC

    Member

  • Members
  • 390 posts
  • Location:Arlington, Texas

Posted 11 June 2009 - 12:24 AM

I'm going to try to make a barrel replacement out of Pvc, to give my streamlines more accuracy. Basicly, I'm trying out a barrel matieriel that I haven't seen used before in a Ls. I'm also going to put a piece of Pvc in the part of the bolt that holds the dart, so the dart can stay centered and i can rip out the piece that the peg is connected to, to give full air flow.

Does this make sense?

PVC's too wide for darts. I mean, it fits snug on my 5/8 stefans, but...

If you're using CPVC, then maybe, but it won't accept clips. Unless I'm misunderstanding, and you're using the stock breech with a new barrel, in which case, good luck aligning them.
  • 0
QUOTE(NerfUK @ May 8 2009, 11:54 AM) View Post

(I forgot to take a picture of my own poppers)

QUOTE(analogkid @ May 20 2009, 10:04 PM) View Post

Every size rod you could ever want.


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users