Jump to content


Photo

Need A Little Help


8 replies to this topic

#1 rokor

rokor

    Member

  • Members
  • 792 posts
  • Location:Mississauga, Ontario
  • State:Ontario
  • Country:Canada

Posted 22 February 2009 - 11:56 AM

Well, I was hoping to be able to get this done all by myslef, but I'm stuck. I neen a way to connect the Magstrike trigger, to the AT3K valve pin. Here are some pictures...

Posted Image

Posted Image

Any help is appreciated.
  • 0
"Sorry rokor...my cousin is gay too...it's okay...we're tolerant"
Talio in Shoutbox.

#2 slowguitarman

slowguitarman

    Member

  • Members
  • 1,113 posts
  • Location:Denver, WV

Posted 22 February 2009 - 12:41 PM

Look up my NF2K. You might be able to connect it similarly to how I did it on that gun.
  • 0
QUOTE
Your dreams were tight like a baby

SGM's Shred Shop -Mod Service

NerfHaven's resident drama queen.

#3 rokor

rokor

    Member

  • Members
  • 792 posts
  • Location:Mississauga, Ontario
  • State:Ontario
  • Country:Canada

Posted 22 February 2009 - 12:49 PM

Look up my NF2K. You might be able to connect it similarly to how I did it on that gun.



I had orginally tried that, but because of when I cut out the slot out of the trigger, there was to much flex. I am looking for a way to use a lot of the trigger to support the connection.
  • 0
"Sorry rokor...my cousin is gay too...it's okay...we're tolerant"
Talio in Shoutbox.

#4 NerfCrazy

NerfCrazy

    Member

  • Members
  • 497 posts
  • Location:Minnesota, 55422

Posted 22 February 2009 - 01:09 PM

First I would say reinforce the trigger because it looks like with a lot of resistance from the air tank it would snap at the top L part. As for connecting them I'm not sure.
  • 0

#5 Split

Split

    Member

  • Members
  • 1,771 posts
  • Location:Hammonton
  • State:New Jersey
  • Country:United States

Posted 22 February 2009 - 01:34 PM

Tried a strip of metal yet? As in, do SGM's solution, but with a 1/8+" thick strip of aluminum or something, with the "grain" running vertically. Shouldn't be much flex at all. I'd attach it to the trigger with two small bolts.. #4-40 should work. I used those in my Crossbow writeup thing.
  • 0
Teehee.

#6 Split

Split

    Member

  • Members
  • 1,771 posts
  • Location:Hammonton
  • State:New Jersey
  • Country:United States

Posted 22 February 2009 - 01:39 PM

Tried a strip of metal yet? As in, do SGM's solution, but with a 1/8+" thick strip of aluminum or something, with the "grain" running vertically. Shouldn't be much flex at all. I'd attach it to the trigger with two small bolts.. #4-40 should work. I used those in my Crossbow writeup thing.
  • 0
Teehee.

#7 rokor

rokor

    Member

  • Members
  • 792 posts
  • Location:Mississauga, Ontario
  • State:Ontario
  • Country:Canada

Posted 22 February 2009 - 01:42 PM

I'll give that a go, thanks.
  • 0
"Sorry rokor...my cousin is gay too...it's okay...we're tolerant"
Talio in Shoutbox.

#8 rokor

rokor

    Member

  • Members
  • 792 posts
  • Location:Mississauga, Ontario
  • State:Ontario
  • Country:Canada

Posted 22 February 2009 - 02:15 PM

My dad's a lawyer, so I can get a couple, but since I found a way to connect it quite simply, I won't be needing them. I use a randon peice of tubing I found under my sink, like a 1/8' thick peice of PVC or something. As soon as I glue it, I'll test ranges.
  • 0
"Sorry rokor...my cousin is gay too...it's okay...we're tolerant"
Talio in Shoutbox.

#9 rokor

rokor

    Member

  • Members
  • 792 posts
  • Location:Mississauga, Ontario
  • State:Ontario
  • Country:Canada

Posted 22 February 2009 - 02:21 PM

double post.

Edited by rokor, 22 February 2009 - 02:22 PM.

  • 0
"Sorry rokor...my cousin is gay too...it's okay...we're tolerant"
Talio in Shoutbox.


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users