Jump to content


Photo

Spiderman Dtg Petg Barrels

I think it's quite clean

7 replies to this topic

#1 QuannyG

QuannyG

    Member

  • Members
  • 41 posts
  • Location:Melbourne, Australia

Posted 24 June 2008 - 06:49 PM

Here is my SMDTG with PETG Barrels. Curiously, no glue was used in replacing the barrels.

Posted Image

The gun was opened up, stock barrels taken out, and the usual was done (op valve glued over, AR removal etc. etc.)

E - Tape was wrapped twice around the PETG like so:

Posted Image

and the barrels are carefully inserted into where the stock barrels go. Then the stock barrels are cut off and is placed over the barrels as seen in the first picture. Sanding of the holes where the original barrels were may have to take place. Looking at my orange "collar", it is a little jagged around the edges, as I don't own a dremel.

Ranges (in order of firing sequence):

Barrel 1 (Centre barrel): 16 m
Barrel 2 (Left Barrel): 21 m
Barrel 3 (Right Barrel): 21 m

Enjoy!

QuannyG

Edited by QuannyG, 24 June 2008 - 07:16 PM.

  • 0
QuannyG: School Captain

#2 CrazyIvan VI

CrazyIvan VI

    Member

  • Members
  • 295 posts
  • Location:Kent, OH

Posted 24 June 2008 - 10:33 PM

16m = 52ft

21m = 69ft

Because I know people will ask.

Anyways, I like the mod, looks really clean because you kept the stock 'collars.' I can't get enough of these guns, they're great for integrating into primaries.
  • 0
I get all giddy when I see VACC browsing a stupid topic. I just know someone is going to get banned.

#3 Dayko

Dayko

    Member

  • Members
  • 1,037 posts
  • Location:Washington
  • State:Washington
  • Country:United States

Posted 25 June 2008 - 01:46 PM

Thats pretty good. Nice job.
  • 0

< One foot in death...The other in life. >
 


#4 OfAllTheNerf

OfAllTheNerf

    Member

  • Members
  • 714 posts

Posted 25 June 2008 - 03:32 PM

Pretty cool. I agree these things are great, and I've got about 10 of them and haven't done anything with them yet (I won't sell them, so don't ask).

Anyways, Looks very clean, althought I'm slightly concerned about the seal without any adhesive whatsoever. It might be tight, but may not be completely airtight. Then again, it might.

-OfAll'
  • 0
[color=#FF6600][Finesse]-[BitchX]

#5 Bomberman

Bomberman

    Member

  • Members
  • 730 posts
  • Location:Olympia, WA Zip: 98506

Posted 25 June 2008 - 03:52 PM

Anyways, Looks very clean, althought I'm slightly concerned about the seal without any adhesive whatsoever. It might be tight, but may not be completely airtight. Then again, it might.

-OfAll'

Acually, in most of my mods with pump guns, I have found that I get a better seal with wrapping the barrel tightly with e-tape, and it makes it slightly removable also. I don't own any SMDTG's, but how is the detonator like that? Is it hard to fire at all? And can you aim it really? I imagine it would be an amazing sidearm because you never need to holster it, and you can work your primary with it on, right?
  • 0
QUOTE(silentsnipe) View Post

It's not like that. I put lube on it and its the same. Its just stuck. And when I cock it back it goes farther back then usual. Also I push as hard as I can and it wont go back in. I've tried the methods and they wont work. Also pics are up.

#6 QuannyG

QuannyG

    Member

  • Members
  • 41 posts
  • Location:Melbourne, Australia

Posted 25 June 2008 - 04:11 PM

OfAll, surprisingly, without adhesive, the barrels are pretty much in that little hole, and it seems as though they're in for the long haul! Bomberman did say that this methods makes the barrels slightly removable, however, when I messed up during the process, I had to use a pair of pliers and a considerable amount of elbow grease. This in turn ruined the barrels.
  • 0
QuannyG: School Captain

#7 CrazyIvan VI

CrazyIvan VI

    Member

  • Members
  • 295 posts
  • Location:Kent, OH

Posted 25 June 2008 - 04:52 PM


Anyways, Looks very clean, althought I'm slightly concerned about the seal without any adhesive whatsoever. It might be tight, but may not be completely airtight. Then again, it might.

-OfAll'

Acually, in most of my mods with pump guns, I have found that I get a better seal with wrapping the barrel tightly with e-tape, and it makes it slightly removable also. I don't own any SMDTG's, but how is the detonator like that? Is it hard to fire at all? And can you aim it really? I imagine it would be an amazing sidearm because you never need to holster it, and you can work your primary with it on, right?



My friend bought a pair of these just for fun, I came over and opened one up, and we Crayola modded it right there at his house due to lack of better supplies.

Needless to say, after I got it out of the casing, and found how compact and neat the trigger assembly and pump were, and basically how compact the whole blaster was, I went home and immediately ordered two sets. I wouldn't say they should be used as a Secondary, but as an integration onto your Primary.

I myself am integrating one into my Titan, one onto my Longshot, and now that I've bought a Big Bad Bow, that front handle is just screaming for me to do something to it, which will most likely end up being a SMDTG.
  • 0
I get all giddy when I see VACC browsing a stupid topic. I just know someone is going to get banned.

#8 Renegademilitia15

Renegademilitia15

    Member

  • Members
  • 516 posts
  • Location:Manchester, WA

Posted 25 June 2008 - 07:11 PM

Good job. Ive been thinking about getting one of these to integrate into my MS and I think you just convinced me to. :huh:

Edited by Renegademilitia15, 25 June 2008 - 07:12 PM.

  • 0
Singled RFS
FA_24's response to Ice's back pain thread:
QUOTE

I used to have that problem until I got circumcised. 15 pounds later I was able to stand up straight.


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users