Jump to content


Photo

3rd Spy Gear Signal Launcher Mod

My best yet.

6 replies to this topic

#1 g-force

g-force

    Member

  • Members
  • 345 posts

Posted 19 April 2008 - 03:54 PM

The point of this mod was to fix my first mods biggest problem, low rate of fire. To do this I used:
16/32 brass
1/2 aluminum
sealent (hotglue, plumbers goop, etc.)
Spy gear signal launcher
Step 1: Cut your stock barrel here
Posted Image
Step 2: cut yourself four 8 inch segments of aluminum and one 3-4 inch lenght of 16/32 brass.
Posted Image
Step 3: Cut your 2k turret 2 inches shorter.
Step 4: Drill holes just big enough to fit a dart into behind each barrel in the turret.
Step 5: put circles of hot glue or plumbers goop around the alluminum tubing and jam it into the turret
Posted Image
Step 6: Take your 16/32 brass and slide it over the circle on the back of the the turret behind where the barrel being fired would be.
Posted Image
Step 7: Put several hot glue or plumbers goop circles around the brass and slide it into the stock barrel.
The finished product will look like this:
Posted Image
Ranges are still the same, 120 feet but it is no longer silent.
  • 0
QUOTE(Carbon @ Jul 28 2008, 03:25 AM) View Post

My god, you actually built it. To that, all I can say is, "bravo".

Chubbs

#2 Quilan Fett

Quilan Fett

    Member

  • Members
  • 678 posts

Posted 19 April 2008 - 04:15 PM

16/32" brass = 1/2" brass.
  • 0
SNAP Shotgun


This guy can see the future!

QUOTE(pokemaster @ Mar 3 2009, 04:18 PM) View Post

hasbro in a nerf war!!!!! dude the will cancel it and confinscate are guns

#3 g-force

g-force

    Member

  • Members
  • 345 posts

Posted 19 April 2008 - 04:34 PM

16/32" brass = 1/2" brass.

Well, ok.

I just changed the aluminum barrels to PETG, Posted Image
To do so just chop the alluminum down to 2 inches and hammer the petg on it is so tight there is no need to seal it that is already done. just put some duct tape on to straighten the barrels and make it look cooler.

Edited by g-force, 20 April 2008 - 02:15 PM.

  • 0
QUOTE(Carbon @ Jul 28 2008, 03:25 AM) View Post

My god, you actually built it. To that, all I can say is, "bravo".

Chubbs

#4 CaptainSlug

CaptainSlug

    Resident Mad Scientist

  • Administrators
  • 4,763 posts

Posted 19 April 2008 - 07:35 PM

Don't you mean 17/32" brass? I've never seen any darts that fit in 1/2" aluminum tube. The aluminum tube I use for barrels has an ID of .527" and an OD of 5/8".

Also your cuts look terrible. You should use a pipe cutter or consider buying some form of power tool or mitre box.

Edited by CaptainSlug, 19 April 2008 - 07:37 PM.

  • 0
The little critters of nature, they don't know that they're ugly. That's very funny, a fly marrying a bumble bee. I told you I'd shoot, but you didn't believe me. Why didn't you believe me?

#5 g-force

g-force

    Member

  • Members
  • 345 posts

Posted 19 April 2008 - 08:21 PM

Thanks for the tip I used a hack saw. If you didn't see my new pic that was exactly why i changed the barrel to PETG and i now get even better results.

Edited by g-force, 19 April 2008 - 08:21 PM.

  • 0
QUOTE(Carbon @ Jul 28 2008, 03:25 AM) View Post

My god, you actually built it. To that, all I can say is, "bravo".

Chubbs

#6 Cannonball

Cannonball

    Member

  • Members
  • 357 posts

Posted 21 April 2008 - 12:43 AM

Nice job with the turret g-force. I like the idea though. If I may suggest though, It'd look better if you cut the existing red barrel shorter and attached the turret closer to blast chamber. It'd look alot nicer and I imagine it'd be easier to use. It all comes down to person preference though so if that works for you...
  • 0

#7 g-force

g-force

    Member

  • Members
  • 345 posts

Posted 21 April 2008 - 04:10 PM

Thank you. i will try that soon although I am waiting to see how your idea for this gun will turn out.
  • 0
QUOTE(Carbon @ Jul 28 2008, 03:25 AM) View Post

My god, you actually built it. To that, all I can say is, "bravo".

Chubbs


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users