- NerfHaven
- → b1g13en's Content
b1g13en's Content
There have been 72 items by b1g13en (Search limited from 04-January 97)
#339879 Where to buy Hot Rod XL Beige Foam Backer Rod
Posted by b1g13en on 30 June 2014 - 04:23 PM in Darts and Barrels
After shipping you're getting it around 8-9 cents per foot depending where you live.
#334770 Better FBR
Posted by b1g13en on 13 October 2013 - 11:20 PM in Darts and Barrels
#331699 Rockwell BladeRunner for homemade?
Posted by b1g13en on 09 July 2013 - 02:18 AM in General Nerf
Thank you for replying. Do you have trouble making small external cuts for like triggers or catch plates?I have one and use it for all cuts I make pretty much. The only think I have found is that it is not going to perform small internal cuts very well.
#331689 Rockwell BladeRunner for homemade?
Posted by b1g13en on 08 July 2013 - 09:30 PM in General Nerf
Has anyone ever used a Rockwell RK7321 BladeRunner for homemade nerf applications. I would like to use it for making straight cuts and
barrel spacers. Any input is appreciated
#325441 BANO #4: Kicking off the season
Posted by b1g13en on 18 January 2013 - 12:48 PM in Nerf Wars
On a side note I'll be bringing panthers and longshots for trade. I am looking for a pumpsnaps, berserkers, and settlers of catan.
#322065 [Northern CA] Planning a Nerf War!
#321831 BANO #2: Bay Area Nerf Out! (California)
Posted by b1g13en on 21 September 2012 - 12:53 AM in Nerf Wars
Yes I am using white foam with green and black felt.I start school on the 22nd, so depending on how my first week goes, I may or may not show up. If i do show up, this will be my first war!
Also, if anybody lives relatively near Palo Alto and can give me a ride, please PM me.
EDIT: Does anyone use slugs with white foam and green felt? I need to know if I should mark mine.
#315131 Calibrating Oversized Dart Diameter to Barrel ID
Posted by b1g13en on 03 May 2012 - 01:02 AM in Darts and Barrels
Have you tried putting the cpvc with blanks in them and heating it in the dryer?I tried heating some cpvc barrel material with a common coffee warmer instead of metal on a cooktop. I had some (19!) barrels cut to 2 1/2" for an absolver. There's a rubber band holding them together. The warmer is not a particularly powerful one. I tried mine on high and it deformed a few barrels so I would stick to low at first. In usage I found it best to load it with darts (to about 1/4" of the bottom) and then place it on the warmer for 15 - 20 minutes (longer for stock darts). It's hard to gauge but my darts melted a bit at the bottom when they were done. A little less gets a tighter dart but over 25 minutes started to deform the surface of the foam.
#305042 Dartsmithing Tips Archive
Posted by b1g13en on 26 September 2011 - 07:43 PM in Darts and Barrels
#302264 10 shot turret attachment
Posted by b1g13en on 25 July 2011 - 09:16 PM in Modifications
#302144 How to make better Slug darts
Posted by b1g13en on 24 July 2011 - 01:25 AM in Darts and Barrels
#302133 Territories
Posted by b1g13en on 23 July 2011 - 11:40 PM in General Nerf
#300132 The Two (or Three) Hour Homemade
Posted by b1g13en on 19 June 2011 - 12:31 AM in Homemades
#297488 LED stefans?
Posted by b1g13en on 23 April 2011 - 10:33 PM in Darts and Barrels
#297475 LED stefans?
Posted by b1g13en on 23 April 2011 - 05:47 PM in Darts and Barrels
The firefly darts uses a sticker that wraps around the dartI realize that it would be way to much weight for a dart. With that being said it confuses me how Nerf used their glowing dart for the firefly.
#295564 Modification and Paintjob Pictures
Posted by b1g13en on 08 March 2011 - 12:27 PM in Modifications
new pump just for fun.
#288657 Modification and Paintjob Pictures
Posted by b1g13en on 20 November 2010 - 02:07 PM in Modifications
top loading 3k
- NerfHaven
- → b1g13en's Content
- Terms of Service and Privacy Policy
- Code of Conduct ·