Videos I can not make. With a quad shot it is easy to get 30 feet of distance...with about as much spread as a standard width door.

The spread is going to be pretty dependent on how you make your shells. Where you point the barrels determines where they go. I made all mine as straight as possible.

EDIT: I am also bumping as I have added a list of all the mods I've done to this baby.

how far does the single go and did you do anything to the launcher piston

I've got no idea how far the single goes. The quad shells are much more useful.

And I only lubed up the launcher piston. Nothing else.

i saw a mod where they teflon wrapped the piston 4 times and put a thicker o ring in his demo and got his missiles to go 45 ft his he also showed all of the compression was in the last inch of the launcher.

like he said ^ MANDATE eye ware at my last event i did not bring my eye wear and got hit in my eye with a stock retaliator it hurt like hell even though it was stock.

I would place certified stock or under 110 fps with stock darts only as my rules 80-110 fps will still shoot over 100ft

Been meaning to find the time to post my tray

https://www.dropbox....032247.jpg?dl=0
https://www.dropbox....032304.jpg?dl=0

I am going to eventually open my RS and when i do I may add another method of transferring power from tray to gun im thinking of mounting a xt60 connector to the occupied side of the gun so i could open it without cutting the negative terminal again... If i ever do make this modification ill make my own thread on how i did it.

Is that possible yet to grind your own plastic up and extrude filament for a 3D printer? If so the idea of getting a 3D printer might be moving up on my list.

LGN

not all 3d printers use abs

making filament is not too difficult you just need to heat the material evenly and precisely until it gets to a uniform consistency then it gets pushed through a die

i donno i think i would have gone the high road and put zombie instead of ebola. Ebola is something very real right now and yes it is hard to actually catch it you need to have contact with infected feces or blood.

Also, If i use a microswitch rated for .5 amps, will some nimH cells or a 2 amp lipo burn it out when i get some crazy stall motors?
and i dont get why lighter flywheels can be dangerous

Normal NiMH can only push at best 1500mA Normal AA can only do .5A or 500mA. If you use a microswitch rated to .5A only .5A can pass through it without generating heat over that can go through it but it will heat and can fail. Example of what can happen you have a stryfe you have blades in it low resistance wire and use a 25-50c battery pack then you use the switch that came with the stryfe the motors will attempt to draw up to 10A when a jam or dart hits the flywheels the only thing your gun has that cant handle that type of load is the switch. When the motors start pulling the amperage the switch passes it as best it can as it exceeds the switch it gets hotter and hotter until thermal failure occurs something burns or melts.

Stock motors with better wires and cleaned up circuits will have little issue with the stock switches and amperage under 3A if you upgrade the brushes/motor and raise the voltage a better switch might be in order.

This is why i feel unless your going for the full rebuild you dont need a lipo pack if your doing wires, motors and a lipo pack why keep the old switches might as well change them too.

What is better? Mabuchi FK180SH 3240's or these? http://www.ebay.ca/i...=item234020055e

The axle are a bit long you will need to cut them probably.

The only thing i can think of is your going to have to trial and error with a universal tv remote there will be 2 codes one to move the launch angle one to launch a disc. It is somewhat complicated but i would try a tv remote see if any buttons or combo of buttons triggers anything.

Other options involve much more complicated methods involving making a new control board with an arduino. It would not be overly complicated to control a 3 position servo a variable speed motor and the launch solenoid. It is beyond my skill but it would be possible.

A easier method might be to buy a second one with a remote they are 65-130 on ebay or find someone with the remote willing to let you record the pulses from it you could then program a select few remotes perhaps even a tv be gone diy type unit you would just need to use the 2 codes from the actual remote instead of the on/off db they flash on the diy chips.


http://www.instructa...e-with-Arduino/

Ebay is a bad source a lot of fake batteries

Stock motors run fine on IMR cells but these are expensive
Nitecore i2 charger
Nitecore d2 charger with car adaptor and battery storage box
Nitecore i4 4 slot charger
d4 4 slot (i have this)

these should fit in a rapidstrike tray in place of the c-cells with the center divider gone
18650 30A discharge
10A imr efest 18650

14500 10A efest


for lipo hobby king has excellent prices and sells through amazon...
charger

1. If I run a 2s 25c LiPo, will it be weaker than Ultrafires or not? (High Discharge but low voltage)
A. It will be equal to running 2 ultrafires
2. If I run a 3s 20c LiPo, is it necessary to change my rev switch into a high current micro switch?
A. Maybe the original switches are rated much lower they will eventually burn out and don't pass as much current but stock motors on 3s you can skip the switch upgrade for now you should think hard about doing it eventually.
3. If I run a 500mAh pack and I'm playing for 5 hours, do I need to bring 2 packs? (don't want to cut shell)
A. depends on motors and play style how heavy handed you are on the rev switch. From what i have found 800-1000 is the biggest that fits in a stryfe with a little bit of modding as in removing dividers and support ribs on the battery door
4. Can anybody give me a link for tutorials on how to charge LiPos using a smart charger? (maybe an IMAX B6 Balance Charger?)
A. Google youtube then "how to use imax b6. first result
5. My LiPo has a JST discharge plug and a JST-XH balance plug, if I want to plug both into my Stryfe or my balance charger, what terminals should I use for the Stryfe and the charger? (Male/Female)
A. The stryfe wont have anything you will need to install something to plug into the balance port and the discharge the jst is what you will plug into the stryfe you will need something like this
6.Do stock motors spin fast on a 2s LiPo? (Related to Question 1)
A. I find they do fine on 2 IMR which would be like a 2s 700mAH 10c
7. How do I solder a Female JST plug to my wire to plug LiPos in? (if you have a link, it's fine)
http://www.amazon.co... plug connector
https://www.youtube.com/watch?v=oqV2xU1fee8
it should be pretty self explanatory you run the two wires into the guts of the stryfe and where the 2 wires connect to the battery tray you connect the jst

google and search will both give you numerous how to on modding the stryfe most commonly a rewire mod first result on google search https://www.youtube.com/watch?v=o4AR9fvwlYw ONLY thing i have to say about the video is those "resistors" are not resistors they are Transistors they drop voltage and increase amperage but are not needed.

odd how all of your questions are not yes or no...

another useful bit of knowledge is here is a listing of max acceptable amperage for a given wire size we would be looking at both chassis is more short bursts and what we would use primarily but for longer use the transmission is important too as at a given amperage the wire will heat up and eventually melt

AWG max Amp chassis  max Amp power transmission
10	55	      15
11	47	      12	
12	41	       9.3	
13	35	       7.4	
14	32	       5.9	
15	28	       4.7	
16	22	       3.7	
17	19	       2.9	
18	16	       2.3	
19	14	       1.8	
20	11	       1.5

So would those motors work with IMRs or trust fires?

yes but not as well as a lipo pack the 180s tend to pull a bit more stall amps than IMR provide the stock motors are not so bad with 2 IMR i tossed 2 IMR 18650 in my battery tray the gun is a whole new beast and the balance it toward the center rather than forward. Mind you mine is stock.

There are a lot of threads on motors it uses the same motors as the stryfe ANY 130 size will fit in the stock spot the pusher motor can be replaced with out modding the shell with a 180 you need to mod the pusher tray. Honestly i want to put a brushless set in mine Mainly due to liking the start up sound some make just think you are getting ready and it is time to start so you flip the master on deet deet doo deet then those motor sounds...

The protection PCB should keep them safe. That's kind of the entire reason it's there.

That said, ultrafires are very unfit for this purpose. A brief google search fails to find their official safe discharge rate. Similar li-ion cells are rated to about 1-2C, which means these can really only deliver about 1A continuous. Those motors ask for 2.8-3.8A at 2.4-3.0V. You're feeding them 11.1V, so they're actually probably drawing somewhere in the ballpark of 10A or more at times. This is for one motor, you're driving two, so double that. 20A is something that even unprotected ultrafire 14500s will never, ever be able to do unless you run something like 10 or 15 of them in parallel.

Ultrafires and their cousin trustfires have their place, but driving motors is not it. Feeding 11.1V to motors rated for 3 is not a good place to be either. Sure, the Tamiyas might be able to handle it, but I'd be very careful. What you really should do is get a 1S (lithium) or 3cell (nickel) battery pack that can deliver enough current.

So back to the beginning question. Are your batteries safe? I'd say probably, but you're abusing the hell out of them, and I'm really not sure how the protection PCB will react.

When higher than normal current is drawn the protection shuts down the cell that cell that is not taking a charge either got discharged below or tripped the circuit. If you must go up to at least imr batteries they will be better off than the ultrafires which i would dispose of at this point or store them in a fire proof box. It sounds like the op over discharged them.

The best option would be a lipo 1s with the highest amperage he could find. Next a single purple efest 18650 30A. after that efest v2 14500 if possible 2 in parallel i have been toying with the idea of reworking my stryfe's battery box to have 2p2s efest 14500 v2 also i would recommend a voltage monitor addition to prevent over discharge in the future.

alright thanks for that.

Well there are two locks involved one in-front of the trigger next to the mag lock and one on the bolt sled itself i removed both from mine and i have no issues you can tell if you are primed by the feel of the trigger too it will feel heavier than non primed with no locks...

the plunger tube may be in upside down that is really the only way the lock on the bolt sled can malfunction

I have recently modified some of my blasters, the mods include AR and lock removal and I was wondering if it is a good idea to put felt pads on the plunger head in order to make the blaster a bit quieter and safer to dry fire. if any one has any info on this topic what so ever please reply. thank you.

yes it is somewhat common Self sticking craft foam is typical it does help plunger life and makes it a bit quieter... If you filled the plunger head with hot glue first some dead space would be removed too.

my brother had put away his rapid strike for a couple of weeks, and now the clip lock button is stuck in the release position making it impossible to keep a clip in it. if anyone has had this problem or knows how I may be able to fix it that would be a lot of help.

try actuating it a few times or take it apart.

try spinning the motor it might be stuck... or burnt out another thing would be make sure all the locks are actuated...

Also kill leader... dont you need a custom Rapidstrike or stryfe/rayven for that these days...

I have recently bought IMR Batteries and have only put about 30 rounds through my Stryfe before the Thermistor shut down my blaster. I will rewire my Stryfe over the weekend, but I was wondering: Is it safe to run a Stryfe on four IMRs for long term usage? I'm using the stock motors. Thanks!

I would not there is a rather steep curve upward on noise from these motors. I would run on 2 or 3 but personally i run 2 and keep 2 charged for when the first 2 are exhausted.

If you need a battery blank i made my own using a sheet of paper and a solid core wire down the center with a coil on either end. I simply rolled a piece of paper around a wire until it was as thick as a AA then put glue on either end then stripped the wire ends and coiled them to form terminals... i have 2 one that is 2 AA end to end long one that is a single AA long removes and sits just as a battery would.