Renegade

This mod will ad substantial weight to your gun and also eliminate any echoes or creaking sounds your guns make. The following write-up is for a crossbow, but it can be applied to any gun.

First and foremost, fuck putting foam in your gun. I fell for it when I first saw it in a write-up too, don't be discouraged. Even when you step up your game and use expanding foam and make it all nice and neat there are almost no benefits.

Step One: Get that foam out of your gun.







Step Two: Acquire some NON HARDENING modeling clay.



Step Three: Put the clay into every non essential nook and cranny of your gun. It is best to smush it down as much as you can with your thumbs in order to ensure no air pockets and that you have a solid rifle.



I find it easiest to work with when you cut the clay into sections and work a single piece into the gun at a time.




This is what my rifle looked like when finished.





I left space at the last two holes so that zip ties could be placed there due to the lack of screws near the top of a modded crossbow.

Step Four: Repeat to other shell.



And there you have it. This mod added over 2 and a half pounds of weight to my crossbow( 2 and 1/2 packages of clay). The gun feels amazing. Just a rock solid feel.

Alright, It's time to start planning for FARMageddon.

What? Farmageddon

Where? Davenport or Bettendorf, Iowa

When? June/First week of July?

Why? To have fun nerfing


As for what to bring and what not to bring, I'm gona have to quote cx.

Bring:

* Nerf guns!
* Lots of darts
* Water
* Sunscreen
* Eye protection
* Good attitude
* Friends

Don't Bring:

* Homemades
* Dangerous darts
* Incindiary devices
* Cheaters


I've got one location in mind already. It's a park inside of the city. Has playground, lots of trees, restrooms, and tables. I'll also be able to "reserve" the location so we don't have to worry about other people being there. I'll keep looking for other locations too and post pictures.

If anyone has any further questions, regarding hotels, or the like in the area feel free to pm/aim me. There's a Menards, Home Depot, Lowes, Toys R us, and other stores if you need to make last minute preperations for the war.

As for rules/war games I'm not sure. Haven't nerfed in way too long and have never attended large scale events. I'm thinkng Team Deathmatch with a set number of lives, maybe a few pistol rounds, and some capture the flag. Post any other ideas too.

So post which dates are good, whether you can come, and the like.

At my local Toys R Us today and spotted the coolest nerf gun EVAR.

Behold.



A motherfutchin purple hornet.

Hand me a cigarette.



Edit/ $19.95 yo /Edit

Renegade’s Advanced Disk Shot Mod

Here it is, the Nerf Disk Shot.



The goal of this mod is to achieve more range using stefans by removing the air restrictors and replacing the stock barrel with one made of PETG.

Parts Needed

PETG a little over 4 ¼ inches

Hot glue w/glue gun

E-Tape

Dremel or hobby knife

Let me start off by saying use whatever barrel material fits your darts. But for this specific mod, you would need either PETG or Brass.



Step 1 Remove all of the screws and take apart the gun. The bottom of the handle is glued on, so take a hobby knife and pry it off after taking out all of the screws.



The internals are very similar to that of a Nitefinder.

Step 2 Unscrew the two screws securing the plunger assembly. Take out that piece. Next disassemble the barrel as shown.



Step 3 Discard the small spring and three pronged orange piece. Take the orange piece with the long plastic stick and drill/cut it out.



The main restrictor is glued onto the plunger tube, unlike in a Nitefinder where it can come out. Cut the three orange plastic pieces holding it in place and sand it clean afterwards.


Step 4 Take the two pieces pictured below and sand the inside of them until the PETG will fit inside it.



Step 5 Put the end of the PETG where it is in the picture below. Superglue, then hot glue it to make it stay and be airtight.



Next superglue the front orange barrel piece in place.



Step 6 The last thing I did was superglue and hot glue the entire barrel assembly onto the plunger tube. Then I wrapped it in some E-tape for added support. Screw it all back into the gun.



Finally, screw the whole gun back together.




Rough Ranges


Stefans: 60ish feet (lightly banded)