All right, so you all know the story with this gun, lets get down to moding it. Here’s the gun stock:
Tools needed:
6in. of ½ inch cpvc
Phillips screwdriver
Hot glue gun
Hammer
Something to pry/smash the orange caps off
1. Surprisingly, the hardest step. Do what ever you can to get the orange caps off (dremel, file, smash, pry, melt, just whatever you can). Then remove all the screws.
2. Take the pump out, and plug it with your hot glue gun. It should look like this (sorry the pic is low quality):
3. Cut the your cpvc with a hack saw, then file the ends.
4. Take the cpvc and pound it down in the valve, and place a ring of hot glue around the cpvc, and it should look something like this:
5. Place all the internals back in the case.
6. Screw the case back together. Now you have a foamy weapon of doom!
- NerfHaven
- → Viewing Profile: Topics: man with many guns
man with many guns
Member Since 11 Oct 2005Offline Last Active Mar 01 2006 11:10 AM
Community Stats
- Group Members
- Active Posts 167
- Profile Views 5,831
- Member Title Member
- Age Age Unknown
- Birthday Birthday Unknown
User Tools
Latest Visitors
Topics I've Started
Supermaxx 750 Mod
05 December 2005 - 07:22 PM
At2k Quad Mod
02 December 2005 - 08:03 PM
AT2K Quaded
The at2k, a great gun once modded, before, not so much. Some of the time the darts don’t even leave the barrel. So lets mod this bad boy. Here’s a pic of it un-modded :
Supplies needed
4x6-8 in. of Cpvc
Screwdriver
Hacksaw
File
Hot glue gun
A hand
A working brain ( I know some of you don’t have this )
1.Remove all screws. It should look like this:
2. Remove the pump from the pump tube and plug it with your hot glue gun. Once your done, place it back in.
3.Remove the turret from the case.
Make sure you keep this piece right here right here, the o-ring:
4. Cut off the end of the barrels with your hacksaw about ¼ or1/8 in. from base type thing. You should see springs and junk, keep on going, and in the middle you should hit a medal post, you want to swerve around that, because it would be a lot more work that is necessary to but through it. This is what it should look like:
5.Cut 4 6-8 inch segments, but make them all the same length, as if you don’t make them the same length you will get varied ranges.
6.Take your turret, and hot glue your cpvc barrels. The best way to do this is to do it 1 at a time, and glue the turret and the barrels, then stick it on, and then glue around it.
7. Place the o-ring back in the turret back, and place the turret on the valve. It should fit back together perfect.
8. Screw it altogether.
9. ~Enjoy
The at2k, a great gun once modded, before, not so much. Some of the time the darts don’t even leave the barrel. So lets mod this bad boy. Here’s a pic of it un-modded :
Supplies needed
4x6-8 in. of Cpvc
Screwdriver
Hacksaw
File
Hot glue gun
A hand
A working brain ( I know some of you don’t have this )
1.Remove all screws. It should look like this:
2. Remove the pump from the pump tube and plug it with your hot glue gun. Once your done, place it back in.
3.Remove the turret from the case.
Make sure you keep this piece right here right here, the o-ring:
4. Cut off the end of the barrels with your hacksaw about ¼ or1/8 in. from base type thing. You should see springs and junk, keep on going, and in the middle you should hit a medal post, you want to swerve around that, because it would be a lot more work that is necessary to but through it. This is what it should look like:
5.Cut 4 6-8 inch segments, but make them all the same length, as if you don’t make them the same length you will get varied ranges.
6.Take your turret, and hot glue your cpvc barrels. The best way to do this is to do it 1 at a time, and glue the turret and the barrels, then stick it on, and then glue around it.
7. Place the o-ring back in the turret back, and place the turret on the valve. It should fit back together perfect.
8. Screw it altogether.
9. ~Enjoy
Knives/swords Collections
26 November 2005 - 04:03 PM
There was a gun topic, so I thought what the heck, why not. Post pictures of your knives/swords here. I'll post my collection:
Feel free to post 1 at a time or all at one.
Feel free to post 1 at a time or all at one.
Nf Mod
13 November 2005 - 12:09 AM
A not so good gun stock e-x3, and doesn’t use it’s full potential. That’s about to change
1.Remove all screws. There should be 14. Open the gun carfully.
Optional step: 2. remove led light
3. Un-screw the plunger, and throw away the pieces but these:
4. Take the air restrictors, and punch them out, by any means. They should look like this:
5.Place now non-restricting air restrictors on plunger tube.
6. Cut 3” inch length of cpvc
7. Hot glue cpvc on plunger tube.
8. Trim case to fit the cpvc.
9.Place all internals in case
1.Remove all screws. There should be 14. Open the gun carfully.
Optional step: 2. remove led light
3. Un-screw the plunger, and throw away the pieces but these:
4. Take the air restrictors, and punch them out, by any means. They should look like this:
5.Place now non-restricting air restrictors on plunger tube.
6. Cut 3” inch length of cpvc
7. Hot glue cpvc on plunger tube.
8. Trim case to fit the cpvc.
9.Place all internals in case
Double Shot Mod
11 November 2005 - 10:31 PM
An alright gun stock.
Our main mod is going to be on the shell not the gun
Tools needed
Hacksaw
Needle nose pliers
Cpvc
1. Take your pliers and remove the middle posts
2. Cut off the end of shell
3. File off end
4. Cut a 2" piece of cpvc
5. Place cpvc in shell, with some e-tap on the end or for a more permient effect put hot glue on the seem
6. Enjoy!
Ranges: About 5- 10 more feet than stock
Our main mod is going to be on the shell not the gun
Tools needed
Hacksaw
Needle nose pliers
Cpvc
1. Take your pliers and remove the middle posts
2. Cut off the end of shell
3. File off end
4. Cut a 2" piece of cpvc
5. Place cpvc in shell, with some e-tap on the end or for a more permient effect put hot glue on the seem
6. Enjoy!
Ranges: About 5- 10 more feet than stock
- NerfHaven
- → Viewing Profile: Topics: man with many guns
- Terms of Service and Privacy Policy
- Code of Conduct ·