maseman 46
Member Since 11 Jul 2008Offline Last Active Dec 30 2016 01:03 AM
Find content
Topics I've Started
Centurion plunger assembly
17 January 2014 - 09:56 PM
Well, I havent seen anything on the plunger assmbly for this gun. Seeing as how I got mine for 10 bucks at fred meyers, ill give it a shot.
This is the first thing I noticed...
Smack this part where it meets the plunger with a hammer. Do it all the way aroud to braek the glue, and remove the one screw
The ya have it. The plunger is also tapered, so only the last like 2 inches actually gets any compression with this seal. Same with the Magnus. Any questions? Just be aware, that if it doesn't break the glue just right, you will have to repair the plunger tube where it separates. If that makes sense
This is the first thing I noticed...
Smack this part where it meets the plunger with a hammer. Do it all the way aroud to braek the glue, and remove the one screw
The ya have it. The plunger is also tapered, so only the last like 2 inches actually gets any compression with this seal. Same with the Magnus. Any questions? Just be aware, that if it doesn't break the glue just right, you will have to repair the plunger tube where it separates. If that makes sense
Rough Cut relief holes
26 December 2013 - 01:54 PM
Its been a long time since I've posted anything. So here goes. I got a roughcut from my cousin. Ive been messing with it. Removed he posts. And I noticed several holes in the barrel assembly.
I know these are to even out the darts power throughout the barrels, but oh well.
The last ones I found are right here
That last image is kinda bad, but you can still see it. The other side has one as well.
Then, of course you got to tape up the seals and throw in some lube
Then I added some hot glue in and around this part, to insure a good seal
As far as range difference? I have no idea. Never tested the gun before hand. Defiantly shoots harder though. Ill get the ranges later. It shoot really good out of the top 4, but the bottom four suck. Please dont kill me if I screwed up
I know these are to even out the darts power throughout the barrels, but oh well.
The last ones I found are right here
That last image is kinda bad, but you can still see it. The other side has one as well.
Then, of course you got to tape up the seals and throw in some lube
Then I added some hot glue in and around this part, to insure a good seal
As far as range difference? I have no idea. Never tested the gun before hand. Defiantly shoots harder though. Ill get the ranges later. It shoot really good out of the top 4, but the bottom four suck. Please dont kill me if I screwed up
I Need Your Opinion
25 February 2009 - 08:47 PM
Ok I need your peoples help. (in a way) I cant figure out what kind of a handle and trigger to use for this gun. I have tried using a scout and crossfire, but those didnt work. I have a stock but i cant find it right now so ill get it later. Here are a couple of pictures for you.
Go U.S Air Force!!!
I would reallt appricate the help. I can answer any questions you need.
Go U.S Air Force!!!
I would reallt appricate the help. I can answer any questions you need.
Ok I Really Need Some Help Here
24 February 2009 - 09:19 PM
Ok so the other day I opened up my BBB and did a simple barrle replacement (well not quite simple but)
And I put it back together and the barrel was completly airtight and the dart shot about three feet. I used about 1 foot of Sch. 80 PVC pipe with stock taggers and even added a recon spring. Here are soome pictures.
Here is the entire assembly.
The springs nested together
The seal and the other peice
The barrel and the glue with the dart stopper
And lastly where the glue and barrel end.
If you can help i would greatly appricate It.
And I put it back together and the barrel was completly airtight and the dart shot about three feet. I used about 1 foot of Sch. 80 PVC pipe with stock taggers and even added a recon spring. Here are soome pictures.
Here is the entire assembly.
The springs nested together
The seal and the other peice
The barrel and the glue with the dart stopper
And lastly where the glue and barrel end.
If you can help i would greatly appricate It.
