17 replies to this topic

[Chewbacca]

Alright. So since I am leaving the U.S. in a few days for the whole summer, I thought I would contribute at least one thing to the Haven before I left. Anyway, here ya go:

Here is what ye shall be constructing:


Supplies needed:
Dremel
Hacksaw (or PVC pipe cutters)
E-Tape
1/2" CPVC pipe
3/4" PVC pipe
1 3/4" PVC coupler
Big Bad Bow
1/2"FBR
Hotglue and gun.

Ok, so step number one: You have to dremel out one side of the 3/4" PVC coupler until two pieces of CPVC can fit inside of it. DO NOT DREMEL OUT THE OTHER SIDE!!!!!!



Oops! I forgot to say, you have to cut two barrels out of CPVC, mine were about 3.5" long. Then, hotglue the two barrels together, and make sure they are about the same length.


Take your newly glued barrels and get them into the coupler (use a hammer if you need to), and take out some of that FBR, and cut out two pieces bout an inch long.


Take these pieces of FBR and stuff them in the holes next to the barrels.


End of part 1

Edited by Chewbacca, 18 June 2007 - 06:40 PM.

[Chewbacca]

Part 2

Now pull out the trusty ol' hotglue gun and warm her up. MAKE SURE THE BARRELS ARE STRAIGHT!!! It is a pain when they aren't. When the hotglue is heated, cover, and I mean COVER the FBR, and the holes around it, pretty much anywhere air could escape with hotglue. Make sure there are very little or no airholes. (I used about 1.5 hotglue sticks on this step)



Wait for the glue to dry.
Ok, now, to to make it even more airtight, bust out your e-tape. cover the base of the coupler, and all of the barrels.


To make the barrel fit on the BBB's original barrel, you have to cut a small length of 3/4" PVC pipe and stick it in the non-dremeled out side of the coupler.To make a tighter fit, add a few layers of e-tape on the original barrel:


Now the 3/4" PVC should have a nice fit, and shouldn't fall off very easily. So now all you have to do is put the barrel on! Here is the finished product.




TA-DA! Now you should have a fully operational BBB with removable "shotgun" barrel

Ranges:
A bit of tail-wind. Ranges were averaged between a few shots. I fired the darts at about a 10 degree angle.
I only used the shotgun barrel while testing ranges.
Stock Darts:
53'

My Crappy Stefans:
~60'


NOTE: I hack-sawed off the tip of my BBB's original barrel, and I cleaned out all air restricting material.

Questions, comments, fears, frustrations?

-Chewie.

Edited by Chewbacca, 18 June 2007 - 06:58 PM.

[Newbie]

Really nice write up! I can't see anything else to make it better.

[Substance Abuse]

It's cool how you made it shoot two darts at once. Very Nice.

[NerfMonkey]

Dart spread at 40'? I'd put the barrels in sideways so the darts spread out a bit to the sides and give you a better chance of hitting someone. Even if they spread now they're still one on top of the other so you'll hit your target once in the face and once in the balls.

[keef]

Nice, but what if you took a plastic splitter, like a Y valve I think it's called, and integrate a at2k pump with vinyl tubing, epoxyed on, and the plunger integrated into the first hand grip or something?

Edited by keef, 18 June 2007 - 08:15 PM.

[Chewbacca]

Even if they spread now they're still one on top of the other so you'll hit your target once in the face and once in the balls.

That made me laugh. I usually have barrels sideways, but they just turned out vertical in the picture.

[Texansharpshooter]

Nice write and pictures. Makes perfect sense. I may try this with mine.

[Quilan Fett]

What's the orange piece on the side of your 3B?

Edited by Qui'lan Fett, 18 June 2007 - 09:34 PM.

[Retiate]

Nice, I also would like to know the dart spread at 40'.
I think you should keep the barrels fairly straight, otherwise the spread might be too much and you wouldn't be able to aim well at all.

What's the orange piece on the side of your 3B?

Looks like a shell for an ammo holder.

[Forsaken angel24]

I put this in the Modification Directory under:

-------------------------------------------------------------------------
>>>>>> Miscellaneous/Not Relevant to Specific Gun Mods
-------------------------------------------------------------------------

Only because this can be done to pretty much any gun.

Thanks for contributing.

[Chewbacca]

EDIT: I tested for spread. At 40', the spread is around 2 feet.

Qui'lan fett: Yes, those are replacement shells for the Double Shot. I just taped them on as ammo holders.

Forsaken_Angel: You're very welcome.

Edited by Chewbacca, 19 June 2007 - 06:36 PM.

[keef]

Nice, but what if you took a plastic splitter, like a Y valve I think it's called, and integrate a at2k pump with vinyl tubing, epoxyed on, and the plunger integrated into the first hand grip or something?

What the Fuck?

Its in another post, "how to salvage two broken air guns and a bbb". You can get double the power with double the bullets.

[Chewbacca]

Its in another post, "how to salvage two broken air guns and a bbb". You can get double the power with double the bullets.

Can I get a link to that? Been searching for a good twenty minutes without any luck. I sawed off the front handle already but it looks like crap. So I have to do something about it.

[keef]

Its right here

http://nerfhaven.com...?showtopic=8798

Its not a bad idea, (sirtofu's mod) but keefs post still makes no fucking sense.

Try reading it, and I mean a T valve, (connects both vinyl tubes to at2k plunger), not a Y valve