10 replies to this topic

[zxnam]

This is a 2 part mod, First a double barrel to fit Gengar003's Clean Coupler Mod, and then a an extra mounted shot in the laser beam area.

For the Double barrel you will need:
Two 3" cpvc lengths 1/2" and one 3/4" section(approximate for both)
Two 1.5" lengths of 3/8" vinyl tubing
Electrical Tape
Glue

1. Cut both vinyl tubing like so, so the tubing will fit.


2. Fit both pieces into the 3/4" length of 1/2" cpvc and glue it down good.

3. Wrap E-tape around the the end of the vinyl tubing so it fits snugly.

4. Slip the 2 sections of cpvc over the vinyl tubing.

5. Glue it down good. Connect the 2 with glue also.



END OF PART I

For Part II you will need:
10" of 3/8" vinyl tubing
Drill
Electrical Tape
Glue
1" stub of 1/2" cpvc
3" section 1/2" cpvc


1. Cut a 1/2" hole in the shell just forward of the trigger.


2. Wrap E-tape around the end of the vinyl tubing so it fits snugly on the cpvc.

3. Slip the cpvc over the vinyl tubing on one end and glue it in.



4. Cut laser like so, opening it up helps.



5. Slide Vinyl tubing through hole and glue the other end in.

6. Position the barrel so you can connect the other end to the coupler, glue it place.



And your done!

[monkey with a nf]

So the barrel in the laser connects to the coupler? I've seen SSPB's in that position, but never another barrel.

[zxnam]

So the barrel in the laser connects to the coupler? I've seen SSPB's in that position, but never another barrel.

Correct, Its more for fun than anything but in an indoor war it can save your life especially when you have another shot totally ready to shoot in 2 seconds.

[JurassicPark]

What's the the range difference from a normal barrel and the lower barrel? That is cool none the less. Nice job.

[zxnam]

About 40 feet , my main gets 80' and the secondary get 40'. I will repost ranges when I get a better spring, I have the stock ex-3 in.

[hard rockr]

About 40 feet , my main gets 80' and the secondary get 40'. I will repost ranges when I get a better spring, I have the stock ex-3 in.

Dude there is no wayyy you get 80' out of a nitefinder. Unless you angle it of course...

[zxnam]

I get 77' average distance flat. My darts have a magical fit in cpvc.

[rebsol]

About 40 feet , my main gets 80' and the secondary get 40'. I will repost ranges when I get a better spring, I have the stock ex-3 in.

Dude there is no wayyy you get 80' out of a nitefinder. Unless you angle it of course...

Says who? My nf gets 70-85 feet.Flat. I have this magical cpvc that fits my darts so well it feels like its almost airtight. I reinforced the plunger, added another o ring, lubricated it, added a #49 spring along with the stock, and took care of all possible leaks.

[blister]

Yea, but he was using the stock spring so its kinda hard to believe. Also, rebsol, you said you added a stronger spring along with the stock spring, too? ....

Edited by blister, 21 June 2007 - 02:03 PM.

[rebsol]

Yea, but he was using the stock spring so its kinda hard to believe. Also, rebsol, you said you added a stronger spring along with the stock spring, too? ....

I wasn't talking about the mod, I was talking about Hard Rockr saying a nf couldn't get 80 feet. I did add another spring, a 49 at ace, but I stretchted the stock one a long time ago and its about as strong as a ls front gun spring. Thats not much at all. Imagine if you put it in the nf you'd get like 15 feet.

[zxnam]

Ok guys, thats enough bickering for one day. Does anyone have any questions about what I did?