19 replies to this topic

[nerfer909]

How did I do, it gets around 87.11 ft. Here are two of them.









I like the minimized one best, by the way, I am a new member, so if I am in the wrong, please tell me.

[n-strike]

I like it. And you are in the right place. Nice job.

[nerfer909]

I like it. And you are in the right place. Nice job.

Thanks, but I dont like the big hole in the minimized one, but I am right now about to fiz it.
I t is my 2nd modded gun, and my best.

[TheCheatIsNotDead]

What mods? What barrel material?

Nice job though. Wish the picture was bigger though.

~TCIND

[nerfer909]

Marker barrel, extra small. and air restrictor removal, and minimization.

[nerfer909]

This is my newest one, I did it about 10 minutes ago.

[nerfboi]

You are technically in the right catagory, but wrong thread. Heres the right place to put it: Mod/ Paintjobs Thread
But back on topic. I loocks really clean. Nice job on it. what are the ranges on thes things?

[Rambo]

The range is posted in the first post. You don't have to put your stuff in the Mod thread. You can if you want...

[nerfboi]

Oooh. Ok then. My bad. i didn't know that. And Sorry I didn't catch those ranges.

[TheCheatIsNotDead]

I am hard pressed to believe that you get almost 90' on a gun where you did nothing but air restrictor removal and barrel replacement (With... is that TWO markers glued together?).

You must have had some crazy wind behind you or something to get a shot like that. And that HAD to have been an arc'ed shot.

~TCIND

[CAP Blue Beret]

That last one, the PPK, looks like the barrel is pointed down a little bit. When my PPK had this, I had to put three rubber bands around the barrel to keep it strait.

[nerfer909]

No its straight, it is just how I took it.

Edited by nerfer909, 29 April 2007 - 01:50 PM.

[nerfer909]

I just bought some 1\2 inch pvc, and upgraded my barrel.

[butleriscool123]

Nice! PVC is waaaaaaaaaaaaaayyyyyyyyyyyy better that marker barrels, good job! I think that was the best NF paint job, its better than the blue and yellow.

Edited by butleriscool123, 12 May 2007 - 11:15 AM.

[nerfer909]

I bought some 12 inch long pvc from home depot for 120, I couldnt find any FBR, where would it be?

[Retiate]

Weather Stripping.
Though be careful, when I got FBR, they had the Frost King brand, and it seems like they have several different factories, all producing foam that have different diameters. So if your going to get some foam, I suggest you buy a lot of it at once, because when they restock, it might be a different size, even though it says 1/2".
Or you could order it off something.

[Dayko]

Nice mods.

Edited by Dayko, 12 May 2007 - 12:35 PM.

[nerfer909]

Thanks, I have already got the fbr, it is it said 1\2 inch, but it is 3\8 of an inch.

I also got the frost king stuff.

Edited by nerfer909, 12 May 2007 - 09:53 PM.

[Newbie]

Most harware stores have it. Make sure to look near caulk saver. If your hardware store does not have it, look Here.

Good luck!

[nerfer909]

I just modded another one, it has a pvc scope, and a pvc handle, pretty handy.



It is verry accurate with stefans, but i pretty much have to use stefans with screws in the end, they shoot the best in this gun.

Edited by nerfer909, 13 May 2007 - 10:24 PM.