25 replies to this topic

[Renegade]

I Haven't seen anyone with much of a DoubleShot Write-up minus shell mods and tricksleeve's. Since no one post's Mod Write-Up's anymore, here it is.



Renegade’s Double Shot Mod



Here we have a stock DoubleShot. All of mine have been horrible stock. This is mainly because of the large “barrel.” The darts usually bounce off the sides and get stuck, or barely leave the barrel. To remedy this, we’ll be sawing off most of the barrel. And then Putting CPVC in the shells for a tighter fit. This allows for the shells to still eject even after being modded.

Step One: Use a hacksaw and saw off your barrels as short as you would like. I cut them right inline with the yellow fore grip.



Step Two: My DS Didn’t let shells eject just by flipping it down with one hand so I took out a little piece that gives it some friction and clicks when it is bent. It is the entire small spring and plastic lever. I used a screwdriver and pried it out.



Step Three: We’re pretty much done with the main gun for now. The next step involves the shells. Cut the shells just below where it dips and gets smaller. CPVC should fit right inside. I cut my CPVC to 2 inches. This kept it near the original shells, although longer lengths could be used but the shells may not eject properly. Use hot glue to seal it. Make the glue nice and close to the shell so none hangs over.



OPTIONAL: I did not see any noticeable range increase from the following step. Although it should give a slight increase.

Step Four: Use a drill to make the hole in the back of the shells a little bit larger. DO NOT make it larger than the small plastic circle protruding out of the shell. This makes the seal.



Step Five: I decided to cut the trigger guard as I felt it got in the way of my fingers. It may not be the same for you.



And now we have a modded DoubleShot. It’s more compact, can shoot farther, and can now shoot stefans. I put some e tape on the handle for comfort.



Ranges are at least 40 feet. I’ll do some more accurate range tests later.

[Jergling]

I saw some bored kids in a baskin robin's playing with one of these once, they were shooting it at the counter. It seemed to have reasonable power, but they may have just had one of those one-in-a-million guns that miraculously works well, like unskipping razorbeasts, or welt-inducing mavericks.

Regardless, 40' is obviously way better than this gun could have acheived unmodded. Are the barrels seriously larger than the dart, that would just be stupid manufacturing/design.


--------------Slightly off topic, just thinking: wouldn't it be better though?-------------

Makes me wonder why they don't hire actual nerfers to design their guns. Even some of the forum noobs could make a better Nerf weapon-given the opportunity to use the company machinery. (Maybe they don't let us design nerf because we would end up with weapons of mass-foam-destruction)

[LastManAlive]

Nice job. I killed my DS (damn those car tires and their crushing strength). I think I might get a new one and try to modify it with better springs and adding your mod to it as well. I might even try puting some kind of rubber o-ring or spacer on the shells to try and get an even better seal.

By the by, do the shells still fly out of the gun when you reload? It looks that where you put the PVC in, it wouldn't touch the spring to launch the empty shell back out.

[Rambo]

I saw some bored kids in a baskin robin's playing with one of these once, they were shooting it at the counter. It seemed to have reasonable power, but they may have just had one of those one-in-a-million guns that miraculously works well, like unskipping razorbeasts, or welt-inducing mavericks.

Regardless, 40' is obviously way better than this gun could have acheived unmodded. Are the barrels seriously larger than the dart, that would just be stupid manufacturing/design.


--------------Slightly off topic, just thinking: wouldn't it be better though?-------------

Makes me wonder why they don't hire actual nerfers to design their guns. Even some of the forum noobs could make a better Nerf weapon-given the opportunity to use the company machinery. (Maybe they don't let us design nerf because we would end up with weapons of mass-foam-destruction)

Who is they? This gun is some off-brand(Buzz-Bee?). Hasbro has engineers that design their guns. A few select members also get to visit the Hasbro headquarters once a year or so. When they are there, they see prototypes and they give their input. I'd say that's better than nothing,

[Forsaken angel24]

Might be a strange question but why do I keep seeing the Nerf logo on the Max shot?
Does everyone like taking nerf stickers and putting them on their max shot or did Nerf own Lanard at one point? or what?

[SHADOW HUNTER ALPHA]

Nice. It looks like a sawn-off shotgun (which it in fact is).

Regardless, 40' is obviously way better than this gun could have acheived unmodded. Are the barrels seriously larger than the dart, that would just be stupid manufacturing/design.

Even the Longshot barrels don't touch the darts. That's why the barrel extention reduces range: there is more time for pressure to escape arouund the dart. This mod, however, reduces that time, and therefore increases range.

[Renegade]

LastManAlive: The shells still eject, but not as far as normall. Due to the extra weight, and that lip being farther down.

Forsaken_angel24: I just stuck some extra Nerf Crossbow stickers on it because cx did. And for some originality. As it looked like most other maxshots.

[TX-2000]

Renegade, I'm liking this DS mod. Makes me wish I didn't destroy my DS or try to integrate an AT2K into it. So you didn't change any of the plunger system or internals at all? When I opened my DS I noticed that one plunger sucks horribly more than the other. The reason being because when you pull the trigger it can shoot one or both of the darts. When you only fire one dart, the one still remaining in the gun sucks due to the way the spring mech works. After modding your DS, do you notice a difference in range when only firing one dart versus firing two?

[Renegade]

Well I did open up the gun once. With the small section of tubing connecting the plunger to the "barrel" I didn't think much could be done there. I did try to make the orange hole where the sir comes out a little bigger. I don't think it really affected it much, so I kept it out of this Write-Up.

I've noticed some difference in firing one dart vs two. Not sure how to fix this. I'll check into it after I finish my nitemav and that write-up.

[Jergling]

They really let members (of the forum) come in? wow.

"they" were the companies manufacturing Nerf-type guns, and I understand that they have engineers, but the engineers have more "cool-factor" (and safety) than power, in mind when designing the guns. Of course, they must be contract-bound to do this, since the idea behind Nerf sales is:

(as in all sales companies)

1. Make stuff look good to profit sales (longshot, max-force line)

2. Don't get sued (did someone say "DO NOT MODIFY' clause?)

Obviously, buzzbee puts functionality so far down on their to-do lists, and power is even lower than that, that the output is what they hope for it to be - safe for parents to let thier kids shoot themselves point blank in the head and not get hurt. Nerf is more powerful, less of a novelty/dollar-store toy, but it does seem a lot more fun to mod a cheap gun, not only does it have a lot of room to improve, but also it's disposable, cheap, and screwed up mods are easily just thrown away. I guess there is a positive side to worthlessness...



thus my currently most commonly used screenname: iSuck

[butleriscool123]

Wow, when I got my double shot, it was quite good stock, for a stock gun. Amazingly the darts havnt ever been stuck in the barrel, even stock. I did that same mod with my shells, it greatly helps the range. Anyways great mod!

[Robonerfer1]

He didn't say they got stuck, he said they bounced off the inside and lost range and accuracy.

[Dayko]

Thanks for the mod. It did wonders on my DS. The ranges are usually 35"-40", the best I got on it was 55" and all these ranges are with out the shell mod( I haven't done it yet).

[Jackman]

I heard some people say the barrel is to large. Why don't you saw off the foregrip, then the barrels. Once you're done that, put PETG where the barrels were, and hot glue the fore grip back on?

[Cmdrmack]

You could do that, and then let us know how it goes. My brother have gone through 3-4 of these things already, so I'm not going to get another one until a really good mod comes along. Give your idea a shot and report back later.

[lionhead333]

Bringing the barrel idea further.
On ebay, if you type in 'nerf gun' you will find that someone has completely removed the front section of a doubleshot. Instead of barrels, there are short cpvc stubs. So long, shells.

[six-five-two]

Yeah I see it too... reading it now. Did you see one of the auctions below it though "Modified Streamline Darts" but it doesn't say what he did to modify it!

EDIT: Finished reading the auction thing and... the flip down part is removed? That's the best part of the double shot, to flick the thing upwards so it looks all gangster...

Edited by six-five-two, 25 June 2007 - 01:15 AM.

[Oro]

Nice mod Renegade, this will be great since Doubleshots at the local Wal-mart are only 8 dollars.

[qwqw801]

what did you use to cut it.

[mystefansdontflystraight]

what did you use to cut it.

In the future, you may want to refrain from posting in topics that are more than 2 months old, let alone 2 years. This is called Necroing, and it is bad. If you want, Pm the author of the topic. If you necro repeatedly, an admin will likely suspend you, maybe even ban you.
Hope this helps.

[General Nerf]

Hey you took my mod. oh well better luck next time. And also the shell does not work properly for me if i make the hole in the back bigger do i drill through or just make it bigger. And another thing for the mod take out the little stick with something to increase range just by a smig though

[VACC]

qwqwwhatever, please read the Code of Conduct and follow it. Thsi topic is very old and your question adds little if anything. The best course of action here would have been to send a private message to the person you are asking.

General Nerf....he took you mod a year and a half ago? If I could understand what the hell you were trying to say I would tell you it's inappropriate for an old topic. Since I cannot, I'm just going to tell you that you've had more than long enough to figure out how that whole punctuation thing works. Add that to the whinny PM, and I've about had my fill of you. It's not gonna take much more to convince me that you're more trouble than you're worth.

[bobman]

How exactly did you get the little yellow lever and spring out.

Thanks.

[nerfer63]

How exactly did you get the little yellow lever and spring out.

Thanks.

Bob look at the post above yours.