Jump to content


Photo

Magstrike Hair Trigger


8 replies to this topic

#1 NerfMonkey

NerfMonkey

    Member

  • Members
  • 1,821 posts

Posted 26 December 2006 - 07:37 PM

I just got a Magstrike yesterday and immediately became pissed off at that annoying little wheel mech that keeps you from depressing the trigger unless a clip is loaded. I opened the gun up to band the bladder, plug up the little hole on the rubber seal sitting on the piston head and see what I could do about removing the wheel mech. I also had another idea while poking around the innards and noticing that the trigger is about 1/4" away from the pin. This was a little irritating to me so I decided to see what could be done about it. This is what I did:

Materials

Magstrike
Phillipshead screwdriver
Hot glue
Balsa

Procedure

First, I had to decide on what materials could be used for the hair trigger mod. I decided on balsa because it's thin, easy to work with and adheres well to just about anything with hot glue. I proceeded to cut two pieces, each about 3/4" long and 1/4" wide, with an exacto:

Posted Image

I glued them together, sandwiching the hot glue in between, and then putting a bit around the outside to keep them together tightly.

Posted Image

Now, unscrew the trigger to make it easier to work with, and glue that slab of balsa on the part of the trigger that pushes the pin down. Get it nice and tight, but be sure not to get any glue on any of the internals.

Posted Image

Stick the trigger back in place and it should look like this:

Posted Image

Now that that's done, here's the little wheel mech we're removing:

Posted Image

And here's the part of it that is connected to the wheel that interferes with the movement of the trigger (notice the square structure behind the piece of plastic jutting out the side of the trigger, which blocks it):

Posted Image

This video shows how it actually works.

Posted Image

Unscrew that whole housing that covers up the guts of the wheel mech and you're left with this:

Posted Image

And the freed up trigger:

Posted Image

And here's how easy it is to depress the trigger with and without a cilp after these mods are done.

Posted Image

So far I haven't run into any problems with the gun from doing these two things, so I highly recommend them. Post away with any questions, comments or criticisms you have.

I hope you've enjoyed another (rare) mod by me.
  • 0
SexD Warves

#2 Pineapple

Pineapple

    Old-school Admin

  • Contributors
  • 1,377 posts

Posted 26 December 2006 - 09:50 PM

NerfMonkey,

That mod is funky.


It's irritating to have to drop a clip everytime you want to fire the thing, and also, I usually use my finger to depress the wheel at the end of play, to eliminate all pressure in the bladder before storing the blaster.

Your mod addresses both issues. Please update if there's any detrimental effects, long term.


I'll probably use plastic stock to do the mod, but good show, chap. Thanks for the video clairification, too.



-Piney-
  • 0
-Piney- of White Dog Hobbies Armory


<!--quoteo(post=209846:date=Feb 5 2009, 06:27 PM:name=boom)--><div class='quotetop'>QUOTE(boom @ Feb 5 2009, 06:27 PM) View Post</div><div class='quotemain'><!--quotec-->
It's to bad you live in hawaii I bet there are not many wars there.Wait what am I saying<b> you live in hawaii you lucky bastard.</b>
<!--QuoteEnd--></div><!--QuoteEEnd-->

#3 Forsaken angel24

Forsaken angel24

    Member

  • Contributors
  • 2,472 posts

Posted 26 December 2006 - 10:07 PM

I dealt with both these issues in my thread.
Here is a link to the whole hair trigger and then some idea.
Follow me.
Even though it was done I was glad to see that it was a good write up.

Edited by Forsaken_angel24, 26 December 2006 - 10:09 PM.

  • 0
I don't get my kicks out of you,
I don't feel the way I used to do.
I know its bad,
After what we had,
But I’m just not the angel you knew.

#4 NerfMonkey

NerfMonkey

    Member

  • Members
  • 1,821 posts

Posted 26 December 2006 - 10:12 PM

My mistake. I never saw that page and thought the only mod writeup you posted for the MS was the bladder expansion. I tend not to check the rest of the thread after the first part of a writeup has been posted unless I know there's another part coming.

I also like the brass mod.

Edited by NerfMonkey, 26 December 2006 - 10:18 PM.

  • 0
SexD Warves

#5 Shadow 92

Shadow 92

    Member

  • Members
  • 193 posts

Posted 26 December 2006 - 10:39 PM

Nice mod and write up, but instead of using balsa I used the spare plastic from the plate part of the wheel mech.
  • 0

#6 SHADOW HUNTER ALPHA

SHADOW HUNTER ALPHA

    Member

  • Members
  • 1,116 posts

Posted 26 December 2006 - 11:17 PM

I decided on balsa because it's thin, easy to work with and adheres well to just about anything with hot glue.

It's irritating to have to drop a clip everytime you want to fire the thing, and also, I usually use my finger to depress the wheel at the end of play, to eliminate all pressure in the bladder before storing the blaster.

-Piney-

Nice mod and write up, but instead of using balsa I used the spare plastic from the plate part of the wheel mech.


Many methods, all effective. Nice work, NerfMonkey. The same for you, Forsaken_angel24.

Edited by SHADOW HUNTER ALPHA, 26 December 2006 - 11:18 PM.

  • 0
The only commonly shared fate among us all is death. I turn to the shadows so that I may not be unfamiliar with hell's corridors when I arrive. - SHADOW HUNTER ALPHA

Founder of the Shadow Militia.
Founder of Nightshade Laboratories and The Nightshade Armament Corporation.

#7 Retiate

Retiate

    Member

  • Members
  • 778 posts

Posted 27 December 2006 - 12:25 AM

Did You see an improvement on ranges when the valve mod was done? Once I fix my leak I'll probably do that, if the ranges go up.
  • 0

#8 NerfMonkey

NerfMonkey

    Member

  • Members
  • 1,821 posts

Posted 27 December 2006 - 12:36 AM

If you mean the "hair trigger" part I'm not sure. I did all these at once because I didn't feel like opening the gun a second time. All I can tell you is that I'm very pleased with it and it's now getting about 50-55' flat, but if you don't mind the long trigger pull don't bother doing the hair trigger because I doubt it would have made a difference in the range.
  • 0
SexD Warves

#9 Forsaken angel24

Forsaken angel24

    Member

  • Contributors
  • 2,472 posts

Posted 27 December 2006 - 02:24 AM

I tend not to check the rest of the thread after the first part of a writeup has been posted unless I know there's another part coming.


I always add more write up to my mods if it affects range or function. The magstrike had three phases.
My ABBB had two phases and the second phase was a huge improvement and only one person commented at the time so I can only assume that alot of members only check the first post on a write up for the actual write up. So Its not like your the only one.
  • 0
I don't get my kicks out of you,
I don't feel the way I used to do.
I know its bad,
After what we had,
But I’m just not the angel you knew.


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users