Jump to content


Photo

Breech Help.


7 replies to this topic

#1 l337n3rf3r

l337n3rf3r

    Member

  • Members
  • 154 posts
  • Location:Westchester, New York

Posted 04 October 2006 - 03:53 PM

I made Unknown's basic breech yesterdy. i Used 1" PVC and 1/2'" PVC. I decided to modify it further and made it clip/magazine compatable. would i need to make a seal for slide back over the covering before firing?

Edited by l337n3rf3r, 04 October 2006 - 04:54 PM.

  • 0
Wii would like to play with you.

#2 Carbon

Carbon

    Contriberator

  • Moderators
  • 1,893 posts
  • Location:Milwaukee, WI
  • State:Wisconsin
  • Country:United States

Posted 04 October 2006 - 06:03 PM

would i need to make a seal for slide back over the covering before firing?


I'm not exactly sure what you mean. But generally, a mag is just a box that's sitting over your breech cutout. Since you made your seal when you made the breech, there's shouldn't be any additional seal needed.
  • 0
Hello. I am Indigo of the Rainbow Clan. You Nerfed my father. Prepare to die.

#3 l337n3rf3r

l337n3rf3r

    Member

  • Members
  • 154 posts
  • Location:Westchester, New York

Posted 04 October 2006 - 06:14 PM

I'm not sure what you mean. I'm not sliding the 1/2"PVC forward. Im leaving it where it is.
  • 0
Wii would like to play with you.

#4 Stormleader

Stormleader

    Member

  • Members
  • 12 posts

Posted 06 October 2006 - 07:15 AM

This is going to sound stupid, But I have searched and found nothing so I am wondering could someone gave me a link the Unknown's breach?Thanks. And on topic I think you have to slide the PVC over it.







Storm
  • 0

#5 Carbon

Carbon

    Contriberator

  • Moderators
  • 1,893 posts
  • Location:Milwaukee, WI
  • State:Wisconsin
  • Country:United States

Posted 06 October 2006 - 10:17 AM

I'm not sure what you mean. I'm not sliding the 1/2"PVC forward. Im leaving it where it is.

In that case, you need to describe what you're doing a bit more, or post pictures. The typical Unknwon breech setup has the barrel (.5" PVC) sliding forward, and the 1" stays put.


This is going to sound stupid, But I have searched and found nothing so I am wondering could someone gave me a link the Unknown's breach?Thanks.


http://nerfhaven.com...zero_ballvalve/

The illustration of Unknown's breech is at the bottom.
  • 0
Hello. I am Indigo of the Rainbow Clan. You Nerfed my father. Prepare to die.

#6 Stormleader

Stormleader

    Member

  • Members
  • 12 posts

Posted 06 October 2006 - 03:17 PM

Thanks Carbon!
  • 0

#7 Nerfnewbie

Nerfnewbie

    Member

  • Members
  • 130 posts

Posted 07 October 2006 - 08:52 AM

Not to get off topic but I didnt want to start a new one. Does anyone know if there's a different way to cut the "hole" for the dart to go in for a breech other than using a dremmal? Sorry about the spelling errors...tired.
  • 0
(\_/)
(O.o)
(> < )

Behold. Helping Bunny on his way, one signiture at a time.

#8 mav3r1c

mav3r1c

    Member

  • Members
  • 18 posts
  • Location:Massachusetts, USA

Posted 07 October 2006 - 10:28 AM

You could use one of the hole cutting bits for a drill.
  • 0


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users