Posted 23 February 2006 - 06:55 PM
Note: I have ALREADY tried using the SEARCH feature.
Posted 23 February 2006 - 07:24 PM
That's it. I'm done. I'm sorry there are breasts on the Internet.
Posted 23 February 2006 - 07:30 PM
- No-iD -
(> <) Helping bunny on his way to World Domination!
Posted 23 February 2006 - 08:20 PM
Posted 23 February 2006 - 10:04 PM
Edited by Raj Man, 23 February 2006 - 10:04 PM.
Posted 23 February 2006 - 11:16 PM
Edited by sam, 23 February 2006 - 11:16 PM.
Posted 23 February 2006 - 11:17 PM
Are you talking about attaching a huge air tank to a tiny SPPB? That seems a little excessive don't you think? I suggest you go with the vinyl tubing tank expansion. 60-70' is more than enough for something that small
Thanks! I'll use one of those ways to remove the restrictor, however, I still have one question. If I directly connected an at2k or 3k tank to the existing tank (a tank expansion), would I still need to seal the release valve? Technically, the level the pressure would need to get to in order to force the release valve to kick in would be much higher after a tank expansion than before it, so is it still necessary to plug the valve? Also, if I were to do a tank expansion, WHERE would I attach the external tank?
Edited by opiumpanda, 23 February 2006 - 11:17 PM.
Hell you're lucky if you don't get fucked with a spiked bat
Posted 24 February 2006 - 08:16 AM
In my experience with the Derringers of Nerf, I've found them to be finicky bastards when it comes to sealing those pistons. Even the slightest bit of plastic dust/shaving/fleck will cause the piston to fail to seal; if this happens, it works best for me to take a paper clip, bend it a bit, and scrape the piston clear of obstruction.
The point of all this, is that when replacing the barrel, be sure to have the barrel pointing down to minimize gunk getting in the piston. Also, the pressure release can be plugged, but it's really not necessary: these things are powerful enough as it is. Also, as far as an air tank expansion goes: yeah, it works, but only to an extent. The valve is only so large, so it would be very easy to create an "air bottleneck" with a larger tank. Honestly, just put a CPVC barrel on there and call it a day.
I tried utilizing simply the valve by adding a larger pump and airtank, but the valve just isn't made to handle much higher pressures (my gun didn't blow, but it was nearly impossible to get it to seal, and when it did, the volumes just weren't there for effective nerfing).
I think the SSPB could be my favorite gun... Makes me feel like a male version of Derringer Meryl, minus the cloak.
Good luck pal, and rock that shitakke at all times.
EDIT: Oh yeah, and Lefty's mod works wonders. The air tank is the cylindrical area between the barrel (piston) and the pump. Basically, the top "L" of the gun is the airtank (not counting the barrel). So, if you were to saw off the pump and the barrel, you'd have an airtank. Which would be worthless. Almost.
Edited by KirbySaysHi, 24 February 2006 - 08:21 AM.
Posted 26 February 2006 - 02:18 PM
So the air tank is NOT here? (The vertical part between trigger and pump)
But instead, the air tank is the section where the vinyl is connected to?
Edited by Jikman, 02 March 2006 - 09:50 PM.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users