#1
Posted 18 December 2005 - 04:49 AM
The actualy operation of the guns is all well and good, but I think it's my darts that's the problem.
To weight my darts, I use either ~>10 12GA Buckshot pellets or one 5.2mm (or rouglhy 1/5") Splitshot. In Australia, these are labeled as Size 00 Splitshot sinkers. For my heavy, "armour-piercing darts" (usually pointed, but never shot at people when tips are pointed) I use 1x Size 1 Splitshot sinker, measuring at 6.8mm or roughly 1/4".
I would use 1/4" steelshot ammo if I could get them.
In YOUR opinion, and in your case, what would be the best weight to use all around. The weapons primarily used here are AT3k's, SF's, PC's, and homemades and a Crossbow.
I'd rather make darts that work well in high power guns and use them in the lower power guns too than lack performance in the high powered guns and get it all out of low powered guns.
-Tidge.
Also active on NerfHQ as Tidge.
#2
Posted 18 December 2005 - 08:40 AM
N3
#3
Posted 18 December 2005 - 10:21 AM
#4
Posted 18 December 2005 - 10:29 AM
For all-purpose I use 1/4" balls or 3/0 sinkers, it's what I use for everything. I don't use the 3/0s though because of the wings on them that make it difficult to center them, but if you can get them without wings, do that.
EDIT: I should also mention that I use megas, but when I used 1/4" balls or 3/0 sinker weighted micros out of my NF, 2k and even Mav and RF20 they all got the best performance.
Edited by NerfMonkey, 18 December 2005 - 10:30 AM.
#6
Posted 18 December 2005 - 11:58 AM
I do, usually just one for my low power guns like the PC and WF, and two or 3 for my high powerd guns.Does anyone use BBs anymore?
Don't forget to eat your meat based vegetable substitute children.
#7
Posted 18 December 2005 - 08:29 PM
If you could point out measurements and stuff, that'd be great.
Also, I use Micros in almost all of my guns. I do use Megas, but not too much.
Are my Size 1 weights the same as a 3/0 weight?
-Tidge.
Also active on NerfHQ as Tidge.
#8
Posted 18 December 2005 - 11:24 PM
#9
Posted 19 December 2005 - 10:39 PM
#10
Posted 27 December 2005 - 09:35 PM
#11
Posted 27 December 2005 - 09:58 PM
Here you go.I should also make note that I don't know how big a 3/0 or 7/0 weight is.
If you could point out measurements and stuff, that'd be great.
Also, I use Micros in almost all of my guns. I do use Megas, but not too much.
Are my Size 1 weights the same as a 3/0 weight?
-Tidge.
From left to right: 1. 1/4" steel slingshot ball, 2. size 3/0 fishing weight, 3. BB size fishing weight, 4. BB.
The slingshot ball is 1/4" in diameter of course, which is 6.35 mm.
The 3/0 is about the same size without the wings, maybe 6.2 to 6.25 mm, it's just a tad smaller. With the wings it's barely over 1/4", maybe about 6.4, 6.45 mm.
The BB size fishing weight is about 3/5 the diameter of the 3/0 without wings; with them it's about 2/3.
The BB is the same size as the BB fishing weight without the wings, about 1/8" or 3.18 mm across.
I waaaay prefer the slingshot balls over everything else I've used, which includes BBs, BB fishing weights, 3/0s and the slingshot ammo. For megas out of a singled 2k, they're ideal and when it was modded for micros the 1/4"ers got about 95' out of it. Sunchip uses 7/0s for his megas out of his singled 2k and gets better range than me, so just try out some stuff and see what works.
Sorry for the bad quality picture, it's hard to take them from a foot away. I don't have any 7/0s, so sorry I can't help you with that.
Edited by NerfMonkey, 27 December 2005 - 10:32 PM.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users