Jump to content


Photo

Homemades Picture Thread

Photos of Homemade Nerf Guns

1306 replies to this topic

#626 flash gordon

flash gordon

    Member

  • Members
  • 5 posts

Posted 06 March 2011 - 11:47 PM

My snaps:

Posted Image

The yellow/black dates from sometime last October. It's basically a Snap Mk. 5, though I wasn't paying attention and picked up thinwall pvc for the plunger tube instead of regular, thick wall. It still has a perfect seal, which I attribute to the fact that the washer that makes the seal is slightly swollen. Hits ~100. This was my first snap, and the pump action grip obviously needed a bit of work, as it isn't the most ergonomic. Still a great blaster though, and it's super lightweight cause of the thinwall pvc.

The blue/white snap has some new stuff in addition to all the basics. Basically an updated Mk. 5, except with a modified superlative head that uses a U-cup seal -- very low friction, 100% seal. It's awesome, hits around 110 with slugs. This blaster is rock solid. The pump action follows Rork's design, using a tee as the grip, which I find significantly better.

Where I deviate from normal design, however, is the 1&1/4 piping the grip rides on. Inside is a homemade air tank filled from the brass nipple you can see there. I don't have internal pictures, but it borrows heavily from Lt. Stefan PVAT, with the crucial difference that: 1) The air flow is better, and 2) It has a constant OD and as such can be combined with pump action for a kick-ass blaster. It's permamently shotgunned to three barrels, which I usually load with a total of 9 darts -- it hits around 90ft. The best of both worlds: pump action and an under-slung shotgun.





PM me with any questions.
  • 0
Wars Attended: WiNCNO 2

#627 Wes7143

Wes7143

    Member

  • Members
  • 758 posts

Posted 13 March 2011 - 12:10 AM

Here's another WIP photo of the bolt action. The blockyness still seen on a lot of the stock will go away as I slowly use primitive tools to grind it down.

Posted Image

A blaster is never really yours until you bleed on it.

Posted Image
  • 0
QUOTE(VengefulWaffle)
Get off my boyfriend


If at first you don't succeed, add more epoxy.

#628 landstricker

landstricker

    Member

  • Members
  • 209 posts

Posted 13 March 2011 - 12:42 PM

My latest SNAP:

Posted Image

It has a 17/32 BritHopp, and a lot of black hot glue to seal up some gaps.
  • 0

#629 blitz

blitz

    Member

  • Members
  • 285 posts

Posted 14 March 2011 - 05:09 PM

Posted Image
  • 0
Blitz, member of the FNBS
"sexual innuendo no intendo"

#630 lionhawk

lionhawk

    Member

  • Members
  • 218 posts

Posted 16 March 2011 - 03:50 PM

My snap, pretty ugly, I know.

Posted Image
  • 0

#631 venom213

venom213

    Member

  • Validating
  • 1,294 posts

Posted 18 March 2011 - 07:34 PM

Homemade Rapid Fire 20 Trigger: This was a long time coming. I have two RF20s that have been out of commission for a very long time, simply because the triggers broke and were lost or destroyed when I attempted to repair them. This homemade one is made out of 1/4" Polycarbonate. The hole drilled in it is 15/64". I hope to make some templates for future versions. This particular one was made by tracing what was left of the stock trigger as well as doing some sketchy measurements to reproduce the broken off part. It turned out acceptable.

Posted Image
  • 0

#632 ricochet

ricochet

    Member

  • Members
  • 108 posts

Posted 19 March 2011 - 04:28 PM

If a picture is worth 1000 words, then a video must be even better. Here is a two part video of how to make a trigger valve for a magstrike or anything like it. Enjoy.

Part 1

Part 2
  • 0

#633 Darth Freyr

Darth Freyr

    Member

  • Members
  • 102 posts

Posted 19 March 2011 - 09:40 PM

Some words first, then pictures. I've been working on a blaster design for a while now. My goals were to have it be comfortable, simple, fairly cheap, and pump action. My first attempt looked like this (1). After quite a bit of thinking, I was able to simplify a lot of the pieces. As it is now, no internal cuts are necessary. The plunger rod is constructed around 10-32 steel threaded rod, with locknuts at both ends and aluminium spacers acting as the catch, similar to that in a 2-11. The catch plate has no slots, and just slides between 4 screws (2). I also got rid of the extra support inside the plunger tube. Adding pump action was just a matter of a 2" PVC grip, a few minor changes, and a sliding plate (3), which I've widened since that one. From there, I went crazy.
*1Posted Image *2Posted Image *3Posted Image
Posted Image
Posted Image
Posted Image
The last one is two plungers connected on the same handle. The top plunger has a 20-tube turreted chopper. The bottom plunger is pump action. The front plate has holes to put darts into.
Posted Image
I'm planning on shotgunning the bottom plunger.
I hope to have a write-up for the basic version in the near future. There are a lot more pictures here, though some are still pretty big. If you have questions, find me on the IRC.

Also, I've heard that some people think Zero valves wouldn't work.

Edited by Darth Freyr, 20 March 2011 - 11:27 PM.

  • 0
Please email me rather than sending a PM. I am DarthFreyr at gmail dot com

#634 diamondbacknf1626

diamondbacknf1626

    Member

  • Members
  • 835 posts

Posted 20 March 2011 - 04:03 PM

EDIT: Thanks to taerKitty, I'ma go ahead and call this the minusBow.

So, my newest toy is sort of a mod to a homemade...I received a PACbow from Ryan McNumbers awhile back, and as expected, it was super awesome. However, recently I decided that the bow arms were annoying, even though I've never, yet, warred with the bow arms equipped. Maybe I just got stuck in too many doorways for my liking...Regardless, a solution was in order. Thus, I present to you my PACbow minus the bow:
Posted Image

Sweet, huh? Here's a little before pic from Ryan's sales thread:
Posted Image

Fun stuff. Basically, where the string used to go through the plunger rod, I added a machine screw, coupled with a nut on either side of the plunger rod, and some vinyl tubing over the screw to keep it nice and smooth-like:
Posted Image
^What you're seeing there is a bit of 1/2" PVC superglued to a flat-washer, with the PVC secured into the end of the [k25] spring. This is meant to keep the [k25] centered properly, and keep it from threading around the machine screw and creating lots of headaches.

[k25], you ask? Yes, [k25]. It allowed me to use a longer spring, keeping some precompression on that spring, makes it mad easy to prime, and it still gets plenty of power, but we'll talk about that later...

Instead of that big ol' dead-space-machine 'T' on the front, a simple, airtight bushing took its place:
Posted Image

Also added a string stop to the back of the plunger rod to dampen the blow a bit. Although not necessary, this keeps the noise down to a minimum, because rather than striking the front of the plunger, the plunger rod is stopped by the string:
Posted Image

I was looking through some threads earlier today, and the above blaster looks eerily similar to Beaver's proposed pump action rainbow variant...with a +bow catch of course as opposed to a rainbow catch.
Posted Image

Ranges:
With a 10 dart hopper (not-pictured), in less than ideal weather conditions, this thing shoots around 130-140'. How cool is that?

Another Edit: Cuz people are cryin...I'd just like to clarify that this can be undone at any point and can be returned to its former bow arm functionality. Easy as pie.

Edited by diamondbacknf1626, 20 March 2011 - 09:18 PM.

  • 0
QUOTE(TxNerfer @ Nov 13 2010, 12:42 PM) View Post

Hey...I got a crazy idea: how about you stop all that sigging stuff? It's not even my thread and it annoys me.

#635 Darth Freyr

Darth Freyr

    Member

  • Members
  • 102 posts

Posted 22 March 2011 - 12:10 PM

Well, I also finished up another blaster recently. It was designed before that other monster, but completed after. It originally had a pinky/ring finger trigger.
Posted Image
I updated it for the middle finger trigger, and finished up the plungers.
Posted Image
Posted Image
  • 0
Please email me rather than sending a PM. I am DarthFreyr at gmail dot com

#636 KaneTheMediocre

KaneTheMediocre

    Belligerent Asshole

  • Members
  • 613 posts

Posted 22 March 2011 - 05:41 PM

This is the apparatus I use to stretch the foam to a more conventional fit. Unstretched, the foam comes fairly tight, comparable to the thick beige foam. It's useable in powerful skirted blasters, or blasters with loose barrels, but we don't want it to jam up anyone's CPVC'd blasters with meh seals, so we stretch it. The resulting foam is a hair tighter than ace foam, but not as tight as the white loghouse foam that I've encountered via Demonlord.

Posted Image

Still working on the whole "lets revolutionize homemade darts to make them safer" business. We've come up with lots of significantly safer designs that fly poorly or don't feed through hoppers. As far as I'm concerned, there is only one good reason not to use stock ammo, and that's hoppers.
  • 0
RAINBOW CLAN FTW
I'm Purple

My Half-Baked MHA Site

#637 pjotrkuh

pjotrkuh

    Member

  • Members
  • 259 posts

Posted 27 March 2011 - 06:02 AM

Made myself a test FPPVAT (Fixed Pump Pull Valve Air Tank):

Posted Image

(So if you can't buy a mega missile, build one!)
  • 0
When the shit hits the fan, you'd better wear a rain coat.....

#638 Y-Brik

Y-Brik

    Member

  • Members
  • 199 posts

Posted 27 March 2011 - 09:25 PM

Made one of these things. I like Hippo's name of RingCatch Pump (RCP)
Posted Image
Uses [k26] over a nylon plunger rod, a skirt seal, Sch80 for the catch ring, and Ace#2 for the primary catch spring. It's held together with #6 wood screws, countersunk of course.
Posted Image
(Holes are drilled for a string stop; I have to get around to installing it)
I got my magic thinwall PVC at Do It Best- 10' for $4, you can order online and have it shipped to your local store free!

Edited by Y-Brik, 27 March 2011 - 09:26 PM.

  • 0

As I said I have not not alot of testes yet but I will be once I finish the mod.

Why I am boycotting Hasbro

#639 Eik

Eik

    Member

  • Members
  • 120 posts

Posted 27 March 2011 - 09:52 PM

Did a bit more work on my VSS-SNAP
Stained the stock
Ghetto'd up a hopper clip– 10 dart capacity
Posted Image
Posted Image

Toooo dark
Posted Image

Edited by Eik, 19 October 2011 - 05:28 AM.

  • 0

#640 Merzlin

Merzlin

    Member

  • Members
  • 589 posts

Posted 28 March 2011 - 05:18 PM

Finished up the pump-action plusbow this morning. McMaster-Carr was packed today
[sorry about the mediocre photos, HTC Incredible's lens does not capture good photos indoors]

Posted Image
Posted Image
Posted Image
Posted Image
Posted Image




And a matching pair:
Posted Image

Edited by Merzlin, 28 March 2011 - 07:00 PM.

  • 0

#641 Ryan201821

Ryan201821

    Prince Edward

  • Contributors
  • 1,892 posts

Posted 29 March 2011 - 04:08 PM

RainbowPACs

Posted Image

Posted Image

Posted Image

Posted Image

Available for sale here.
  • 0

#642 Ozymandias

Ozymandias

    Member

  • Members
  • 201 posts

Posted 30 March 2011 - 12:57 AM

Posted Image
Posted Image
Posted Image
Posted Image

Works similar to my first breech, just with clips.

That is acryllic with an ID of CPVC's OD (5/8),

The epoxy putty is so the 'bridge' doesn't crack.
  • 0
If you wish to post anything HvZ related, here ya go.

"...if you've ever suffered the effects of a fucking faggot retard overpopulation, you'll understand what devistaiting effects it can have on one's psyche." - Talio

#643 Lucian

Lucian

    Member

  • Members
  • 446 posts

Posted 30 March 2011 - 07:59 PM

Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image

Woot.
  • 0

Contact me for design consultation relating to 3D Printing, CNC Machining, and Laser Cutting. I am always happy to collaborate on viable Open Source projects and/or business ventures. 


#644 diamondbacknf1626

diamondbacknf1626

    Member

  • Members
  • 835 posts

Posted 30 March 2011 - 09:46 PM

For you, Mr. McNumbers...I hope you're happy :P
Posted Image
Yayayayay cell-phone camera quality!
  • 0
QUOTE(TxNerfer @ Nov 13 2010, 12:42 PM) View Post

Hey...I got a crazy idea: how about you stop all that sigging stuff? It's not even my thread and it annoys me.

#645 GeshmanWG

GeshmanWG

    Member

  • Members
  • 82 posts

Posted 30 March 2011 - 10:36 PM

QuadCB
Posted Image
Write-up here

Apperently there is no limit to how big of a hopper you use on a cobra. (I wouldn't suggest actually shooting people with a singled cobra) Also for those of you who think streamlines don't work in hoppers,
my cobra begs to differ.
Posted Image
  • 0

#646 Lucian

Lucian

    Member

  • Members
  • 446 posts

Posted 01 April 2011 - 04:55 AM

Doesn't look very homemade ^

Posted Image
Posted Image
  • 0

Contact me for design consultation relating to 3D Printing, CNC Machining, and Laser Cutting. I am always happy to collaborate on viable Open Source projects and/or business ventures. 


#647 Eik

Eik

    Member

  • Members
  • 120 posts

Posted 01 April 2011 - 05:37 PM

New aesthetics
Posted Image
Posted Image
Posted Image
Accessory rail w/ trigger guard
Iron sights
Slick new paint w/ logos
Got some laquer on the stock, with "E" burnt in

I promise this is the last time I'll bring this SNAP up for a while...
  • 0

#648 venom213

venom213

    Member

  • Validating
  • 1,294 posts

Posted 16 April 2011 - 09:48 AM

Plusbow: This blaster has been through a lot. It was originally made my Hereticorp (aka herpescorp) over two years ago. Koree purchased it from him and used it for several months. Beaver was then given hold of the +bow with an objective to sell it. I bought it in an extremely degraded state. I tried fixing up what I could, but it was still nothing spectacular. Here's some random picture I have of it with a SGSL attached.

Posted Image

When I stayed at louiec3's house for ILFF 3 in July, I brought along my +bow for him to repair. He did a marvelous job; stabilized everything, new side plate, new plunger rod, etc. Since then, I replaced the plunger tube with a 1.5" Stainless Steel Sink Extension. It has more volume than the original, looks awesome, and is easier to clean. The seal for the stainless steel tube is two 1.5" OD Rubber Washers. Here's Louie marveling about it the night before:

Posted Image



Posted Image


With my usual massive hopper clip.

Posted Image

Edited by venom213, 20 April 2011 - 03:55 PM.

  • 0

#649 diamondbacknf1626

diamondbacknf1626

    Member

  • Members
  • 835 posts

Posted 16 April 2011 - 11:19 AM

So, a little bit of gun porn...this is the entirety of my collection...the homemade branch, anyway.  Starting to build it up again.  I know I've probably posted about a couple of these blasters already, but in case you happened to miss them:
Posted Image
^My PAC, which I had at one point converted to spring power, and it was awesome, but then, after getting the blaster pictured below, I decided to convert it back.  It's super cool, and I think I'm going to paint the bow arms entirely red...cuz the red just looks super cool.

Posted Image
My RBP along with it's little bro, an LpL-sized pistol but with a Rainbow catch, which, IMO, is much sleeker and super cool in comparison.

Posted Image
And in the realm of opaque PVC...my fav SNAPbow, which rapes unbelievable amounts of face, as well as it's little bro, which I made today.  This little one shoots about as far as its polycarb cousin above it.

A better pic of the little guy, seeing as I haven't posted a pic of it yet:
Posted Image

Posted Image
One big happy family :D

My two other SNAPbows, that are equally as awesome as the first:
Posted Image
The top one I made at the house I was renting while my house was being rebuilt with like, zero modding supplies.  The bottom one, I actually prefer w/o a stock...I just run a hopper on it and shoot from the hip.

Also, I guess this is a homemade...
Posted Image
Louiec3 made it...it shoots really far.
  • 0
QUOTE(TxNerfer @ Nov 13 2010, 12:42 PM) View Post

Hey...I got a crazy idea: how about you stop all that sigging stuff? It's not even my thread and it annoys me.

#650 KaneTheMediocre

KaneTheMediocre

    Belligerent Asshole

  • Members
  • 613 posts

Posted 16 April 2011 - 07:50 PM

I finished a bullpup, rodless pump action blaster yesterday. Has numerous flaws which necessitate a rebuild, but it's a working blaster, and it's about as compact as pump-action blasters get. Has 5.25" of draw, and shoots about 90-100'. Not quite +bow powerful, but closer than I expected to get.

Posted Image


Here's a size comparison with a rainbowpump:

Posted Image
  • 0
RAINBOW CLAN FTW
I'm Purple

My Half-Baked MHA Site


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users