Jump to content


Photo

Rapid Red Writeup: Shell Integration, LEDs & Modification

rapid red shell integration erictzh eric tzh led nerf mod rebelle meishel 2.0 modification

No replies to this topic

#1 EricTzH

EricTzH

    Member

  • Members
  • 19 posts

Posted 31 August 2017 - 02:26 PM

Before reading this,
I highly suggest to Watch The Timelapse Video first:
 
 
2shatSC-TU6SNGrJKrItlQ.png
 
lHXmLYQQT8CBaq3xPUHY5g.png
 
QM_QoqtSQCW1ri28LUrrpQ.png
 
Project Overview:
This writeup is about my rapid red modification and shell integration. I will be using this blaster mainly for CQB and HvZ games. I choose Rapid Red is because they are the most affordable option to try new stuffs, compared to many other flywheel blaster after the discontinued of Stryfe. 
 
Aims
- For HvZ and CQB Games
- Operatable by a single hand (as another hand will be holding a foam sword) 
-Lights up my way at night (while eye friendly) 
- Medieval Classical Feel (Because I love it!) 
- LED design that looks cool
- Solve small handle problem 
 
Things I've Done
- DIY Stock made by lightweight material 
-  Shell Integration : Adding new Handle from Distruptor's (the "New Strongarm" ), Distruptor's Priming Slide for Stabilizing Stock. 
- Internal Modification : Meishel 2.0 Motor
- Paintjob 
- Others: Quick Mag Releases, LED wiring 
 
General Mod Material
-Epoxy Putty: Wood and WaterWeld
-Epoxy Gel
-DAP contact cement 
-Semi Transparent Plastic Folder
-LEDs Diode and Resistor 
- UPC pipe
 
Wiring Materials:
-Meishel 2.0 Motor
-Submianiture microswitch
-18 Gauge Silicon Wire
-950mAH Li Po (Not recommended for Stryfe, for Stryfe use this for higher amperage : 1300 mAH Li Po) 
 
-Dremel Rotary Tool and Attachments: Grinder, Sanding, Enforced Cutting Wheel
-Hack Saw
-Soldering Iron and Solder
-Wire Striper and Wire Cutter
-Hot glue gun and Hot glue sticks 
 
Paintjob Material
-V&F Black Automotive Base Coat
-Aged Copper Spray Paint
-Cheap Acrylic Paint from Walmart: Black White Red Blue Yellow 
-Antique Gold Acrylic Paint 
-Wheel Clear Coat
 
Step 1: Disassembly 
All parts from Rapid Red are disassembled. 
AG33uuAATsWQhkQjRC8ung.png
 
Remove some internal parts in Distruptor that is close to the Handle, Take out the Priming Slide. 
 
 
 
Step 2: Shell Cut
Cut off the Rapid Red Handle, then throw it away. 
6Qt8gknMR2i-7KStVZhg3w.png
 
Cut off Distruptor Handle
jOOlDyLMSBC4bUHRxU8nLA.png
Some trimming will be needed to allign the new handle to the rapid red. 
MNWlVcxpRDa53lptjZUUjA.png
 
Cut off the "back half" of the Priming Slide, This will be used to hold the DIY stock. 
FNjPM6xwSHqVlKuj_MD8Uw.png
 
Step 3: Combining Shell
Drill a hole at the back part of the blaster. 
 
I use contact cement to temporarily hold the handle before apply epoxy putty.
8JDUk5hDSgao1TkncGeEtQ.png
 
Applying Epoxy Putty on Handle and the Priming Slide to Rapid Red Body
VaPsjoU9Rji75RKbdDnSkA.png
 
Using Epoxy Gel as internal reinforcement (But then I realised SmoothCast is a way more cheaper option)
x1YnX9SFQl6utS38Xnvd5w.png
 
Step 4: DIY Stock 
Cut out your choice of pipe(I use UPC not PVC here), apply epoxy putty to stick them to the blaster.
6Feh24buTAqsW0sybAiWkg.png
 
I choose a  rubber flat vacuum wand I thrifted from Goodwill, because it is lighter than plastic and wood.
_AsycfmhRsWOkxcySc9QZA.png
 
Rubber vacuum wand flex a lot, so applying epoxy putty directly wouldn't works. I nailed a small piece of wood on it ( I get this wood for free, you can get some small wood in Walmart DIY Crafting area )
MA4aqFVlRryvW9zSTk1bmg.png
 
Step 5: LED Holes
Use a sharpie to mark out places that I want to cut a hole
eh9yMlMCRsedt_AJVR9Gqg.png
 
Use Dremel drilling attachment to drill the holes
jLmCVYEmQCGlagJL9xcNGA.png
 
Sand the cutted holes so it looks smooth
SWqu0-twTpiCCApv6pA3SA.png
 
We need something to dilute the LED lights. Cut off some semi-transparent plastic sheet(I use semi-transparent plastic folder), hot glue them to those holes.
do-mSs53SLefs8uUSYLk0Q.png
 
Step 6: Paint Job 
Sand the body of Rapid Red
a8IvVgmeR9OIJ2-YcZUWzg.png
 
Base coat using Automotive Vinyl and Fabric Black
wlROh2VJRKO1_giAizgrDg.png
 
Glue Gun Drawing, set the temperature to High, and draw the pattern.
CRd1rbaESt6Y0c5to_v5fw.png
 
Base coat again on Hot Glue patterns, using Automotive Vinyl and Fabric Black as well
JM-c7eGjSkiBaVb_-brIDA.png
 
Aged Copper Spray Paint
VZJR6AjtSI_lcxcbY_PEtQ.png
 
Adding black Acrylic Paint(mixed with around 1-1 water)for blackish shadow effect
Uc6gHrgfT2ioY4YWwNVQvQ.png
 
Use a Dry brush/ Sponge, rub some dry gold paint on it.
l0oFS5ZrSPSo5Dhjzv-7ug.png
 
Paint a layer of Black Acrylic Paint at the bottom half.
saeKNBHFQOibRnMenuW86Q.png
 
After the black paint dries, mix red paint with a little bit of water, brush on the black surface, rub it with your finger/fabric. To make it bloooodyyy cool.
xVGrTLIsRP2T6Dl2IeWioQ.png
 
Step 7: Internal Wiring and Necessary Shell Cut
I use Meishel 2.0 motor, subminiature switch and 18 gauge wire.
 
Some parts are needed to be grind off (Dremel grinning atachment) in order to fit the Li Po
TFJnbrJrQQqbhFdkCNRBng.png
 
Q7WO1RjHTCiLFfOLsB9f6w.png
 
Soldering.
JwMFFBFST2C2GzB3BxW7FQ.png
 
Test motor spinning direction
ZucJZsFiQieJJf0ooxNfwg.png
 
Step 8: LEDs and Magazine Fit
Solder 
DKl2PDzVRlGfKMwPN3j7rg.png
 
Qe0oEskJQLq6L6JRpPqbkg.png
 
Before closing the shell, I tried a couple times of reopening the whole thing, readjusting and do extra shell trimming, so that it fits the magazine, rev trigger and able to be closed .

 

dpM_vensQTKbbDTHNVh0YA.png


Edited by EricTzH, 01 September 2017 - 01:31 AM.

  • 0



Also tagged with one or more of these keywords: rapid red, shell integration, erictzh, eric tzh, led, nerf, mod, rebelle, meishel 2.0, modification

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users