Jump to content


Photo

Clear Shot/Stormfire: Seal Improvement & Spring Swap


3 replies to this topic

#1 NetherMax1

NetherMax1

    Member

  • Members
  • 12 posts

Posted 13 March 2016 - 03:47 PM

So I had a Clear Shot, and it was terrible (read: Crap Shot). Anyway, I had a spare NF spring, a screwdriver. and a bit of teflon tape. Now it's much better.

 

Supplies

  • Cup to hold your screws
  • Nite Finder spring or the equivalent
  • Teflon tape
  • Philips Head Screwdriver
  • Table
  • Stormfire/Clear Shot

Step One

The Subject Before Surgery:

IMG_0297.JPG

 

Lay the blaster on the table and start unscrewing the screws. (Note:They are of varying size, so be careful.)

There's a screw here:

IMG_0298.JPG

and some hidden ones in the priming slide:

IMG_0299.JPG

Once you have them all out, remove the one half of the shell.

 

Step Two

Internals shot:

IMG_0302.JPG

 

Remove the plunger rod assembly (the gray part with the spring on it):

IMG_0303.JPG

 

Now, unscrew the plunger head from the plunger rod and take it apart. It should look like this:

IMG_0306.JPG

 

Ignore that for a second.

Take your new spring out. Then, pull off the old spring and put the new one on in its place.

 

Go back to your plunger head. Take the bottom piece and wrap a bit of teflon tape around it, then replace the o-ring where it was:

IMG_0307.JPG

 

Put everything back together and enjoy!

 

 

Ranges

N/A (I'll add ranges when the weather here is a bit nicer).


Edited by NetherMax1, 13 March 2016 - 03:51 PM.

  • 0

Talio:"Negative points for no pirate monkey."

 

Who needs silence when you have full-auto?


#2 Sketch Art Online

Sketch Art Online

    Member

  • Members
  • 25 posts
  • Country:United States

Posted 15 March 2016 - 04:10 PM

great write-up.  Something i would like to try is cutting off the front part in front of the dart holder to kind of even out the proportions.  Thanks for the write-up. PS how are you in members if you have only 4 posts?


  • 0

Do not aim at eyes or face


#3 Kilomona

Kilomona

    Member

  • Members
  • 108 posts

Posted 15 March 2016 - 04:30 PM

great write-up.  Something i would like to try is cutting off the front part in front of the dart holder to kind of even out the proportions.  Thanks for the write-up. PS how are you in members if you have only 4 posts?

I don't exactly know how the member system works, but it did the same for me. I think a good post like this qualifies you as a member in my eyes. But yeah, I do thing the front bit could be cut off.
  • 0

#4 NetherMax1

NetherMax1

    Member

  • Members
  • 12 posts

Posted 16 March 2016 - 05:09 PM

great write-up.  Something i would like to try is cutting off the front part in front of the dart holder to kind of even out the proportions.  Thanks for the write-up. PS how are you in members if you have only 4 posts?

It auto-members you at some point.

 

 I think a good post like this qualifies you as a member in my eyes.

Thanks.

 

 

 

Hope you enjoy wrecking face with that!


  • 0

Talio:"Negative points for no pirate monkey."

 

Who needs silence when you have full-auto?



0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users